scholarly journals Improvement of Physicomechanical Properties of Pineapple Leaf Fiber Reinforced Composite

2018 ◽  
Vol 2018 ◽  
pp. 1-7 ◽  
Author(s):  
K. Z. M. Abdul Motaleb ◽  
Md Shariful Islam ◽  
Mohammad B. Hoque
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Water Uptake ◽  
Bending Strength ◽  
Alkali Treatment ◽  
Fiber Surface ◽  
Fiber Content ◽  
Pineapple Leaf Fiber ◽  
Bending Modulus ◽  
Leaf Fiber

Pineapple leaf fiber (PALF) reinforced polypropylene (PP) composites were prepared by compression molding. The fiber content varied from 25% to 45% by weight. Water uptake percentages of the composites containing various wt% of fiber were measured. All the composites demonstrated lower water uptake percentages and maximum of 1.93% for 45 wt% PALF/PP composite treated with 7(w/v)% NaOH. Tensile Strength (TS), Tensile Modulus (TM), Elongation at Break (Eb %), Bending Strength (BS), Bending Modulus (BM), and Impact Strength (IS) were evaluated for various fiber content. The 45 wt% PALF/PP composite exhibited an increase of 210% TS, 412% TM, 155% BS, 265% BM, and 140% IS compared to PP matrix. Moreover, with the increasing of fiber content, all the mechanical properties increase significantly; for example, 45 wt% fiber loading exhibited the best mechanical property. Fibers were also treated with different concentration of NaOH and the effects of alkali concentrations were observed. The composite treated with 7 (w/v)% NaOH exhibited an increase of 25.35% TS, 43.45% TM, 15.78% BS, and 52% BM but 23.11% decrease of IS compared to untreated composite. Alkali treatment improved the adhesive characteristics of fiber surface by removing natural impurities, hence improving the mechanical properties. However, over 7% NaOH concentration of the tensile strength of the composite reduced slightly due to overexposure of fibers to NaOH.

Influence of Alkali Treatment and Fiber Content on Mechanical Properties of Pineapple Leaf Fiber (PALF)-Reinforced Cement-Based Composites via Full Factorial Design

2020 ◽  
Vol 1005 ◽  
pp. 65-75
Author(s):  
Charmane Dawn H. Esper ◽  
Hana Astrid R. Canseco
Keyword(s):  
Tensile Strength ◽  
Flexural Strength ◽  
Alkali Treatment ◽  
The Philippines ◽  
Fiber Content ◽  
P Value ◽  
Tropical Regions ◽  
Pineapple Leaf Fiber ◽  
Full Factorial ◽  
Leaf Fiber

In tropical regions such as the Philippines, pineapple leaf fiber (PALF) is abundantly available as a low-cost and renewable source for industrial purposes. In this research, PALF was used as a reinforcing material for cement-based composites to open up further possibilities in waste management. Since natural fibers are not fully compatible with the matrix due to their hydrophilic nature, surface treatment is necessary to enhance the fiber-matrix bonding. Fibers were treated using sodium hydroxide (NaOH) with varying concentrations (4%, 8% and 12%) for 6-hr immersion time at room temperature. PALF was then added at varying content (1%, 4% and 7% w/w cement) to the concrete mixture with a design mix ratio of 2:1 (sand: cement) and a constant water-cement ratio of 0.55. The samples were mechanically characterized after 28 curing days following ASTM C209 and ASTM C473. Full factorial experimental design (FFED) was used to investigate the effects of alkali treatment and the fiber content on the mechanical strengths of the composite. Experimental methods, analysis of variance (ANOVA) and normality test were carried out to evaluate, analyze and validate the results. The best results for tensile strength parallel to the surface and flexural strength at 2.028 MPa and 1.495 kN, respectively, were observed at composites with 1% PALF with 4% NaOH. Meanwhile, composites with 1% PALF with 12% NaOH showed the best result for tensile strength perpendicular to the surface at 1.681 MPa. According to ANOVA results, only the model for the tensile strength perpendicular to the surface showed a curvilinear behavior (p-value=0.012). Results revealed that the factor with the most significant effect was the interaction of the fiber content and alkali treatment on the tensile strength parallel to the surface (p-value=0.000), tensile strength perpendicular to the surface (p-value=0.001) and flexural strength (p-value=0.001).

scholarly journals Effect of Gamma Radiation on the Mechanical Properties of Natural Fabric Reinforced Polyester Composites

2019 ◽  
Vol 27 (4(136)) ◽  
pp. 88-93
Author(s):  
K.Z.M. Abdul Motaleb ◽  
Md Shariful Islam ◽  
Rimvydas Milašius
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Gamma Radiation ◽  
Bending Strength ◽  
Polyester Resin ◽  
Radiation Doses ◽  
Elongation At Break ◽  
Bending Modulus ◽  
Polyester Composites

Two types of composites:(1) pineapple fabric reinforced polyester resin (Pineapple/PR) and (2) jute fabric reinforced polyester resin (Jute/PR) were prepared and the mechanical properties investigated for various gamma radiation doses ranging from 100-500 krad. Properties like tensile strength, Young’s modulus, elongation-at-break, bending strength, bending modulus and impact strength were increased significantly by 19%, 32%, 45%, 32%, 47% and 20%, respectively, at a dose of 300 krad for Pineapple/PR, and by 47%, 49%, 42%, 45%, 52% and 65%, respectively, at a dose of 200 krad for the Jute/PR composite in comparison to the non-irradiated composite. Gamma radiation improved the mechanical properties, but overdoses of radiation even caused a reduction in them.

Study on Degumming Technology and Properties of Pineapple Leaf Fiber

2014 ◽  
Vol 484-485 ◽  
pp. 70-74
Author(s):  
Yu Ling Zhao ◽  
Zhuo Zhang
Keyword(s):  
Mechanical Properties ◽  
Good Condition ◽  
Fiber Surface ◽  
Relative Strength ◽  
Good Effect ◽  
Gravimetric Analysis ◽  
Scanning Calorimetry ◽  
Advantages And Disadvantages ◽  
Pineapple Leaf Fiber ◽  
Leaf Fiber

This paper analyzes several existing pineapple leaf fiber degumming methods and their advantages and disadvantages and describes its relationship with the degumming from the structure characteristics and chemical properties of pineapple leaf fiber. The author puts forward the pineapple leaf fiber degumming technology should be to "high-quality, efficient, low consumption, low pollution" direction of development, and put forward a new method of degumming. By means of scanning electron microscope, infrared spectroscopy, mechanical properties, thermal gravimetric analysis, differential scanning calorimetry and other means, to study the structure, mechanical properties and thermal properties of pineapple leaf fiber biochemical degumming treatment. The results show that: biochemical degumming can take off the original fiber, fiber surface glue residue, single fiber are glial exist, but the fiber separation in good condition, the fiber surface is smooth; hemicellulose degradation in biochemical degumming process, but did not completely removed; no effect on biochemical degumming of pineapple leaf fiber structure has good effect, degumming the treated fiber; degumming relative strength; fiber still has relatively high heat resistance.

scholarly journals Application of Natural Plant Fibers in Cement-Based Composites and the Influence on Mechanical Properties and Mass Transport

Materials ◽  
2019 ◽  
Vol 12 (21) ◽  
pp. 3498 ◽  
Author(s):  
Kaiyue Zhao ◽  
Shanbin Xue ◽  
Peng Zhang ◽  
Yupeng Tian ◽  
Peibing Li
Keyword(s):  
Mechanical Properties ◽  
Elasticity Modulus ◽  
Fiber Content ◽  
Modulus Of Rupture ◽  
Chloride Diffusion ◽  
Ramie Fiber ◽  
Plant Fibers ◽  
Natural Plant ◽  
Pineapple Leaf Fiber ◽  
Leaf Fiber

Recently, there is ongoing interest in the use of natural plant fibers as alternatives for conventional reinforcements in cementitious composites. The use of natural plant fibers makes engineering work more sustainable, since they are renewable, biodegradable, energy-efficient, and non-toxic raw materials. In this contribution, a comprehensive experimental program was undertaken to determine the influence of pineapple leaf fiber and ramie fiber on the mechanical properties and mass transport of cement-based composites. The compressive strength, tensile strength, modulus of elasticity, modulus of rupture, fracture energy, flexural toughness, coefficient of capillary water absorption, and chloride diffusion were measured. Natural plant fiber-reinforced cement-based composites (NPFRCCs) containing pineapple leaf fiber and ramie fiber, as compared to the plain control, exhibited a slight reduction in compressive strength and a considerable improvement in tensile strength, modulus of elasticity, modulus of rupture, and flexural toughness; the enhancement was remarkable with a higher fiber content. The coefficient of capillary absorption and chloride diffusion of NPFRCCs were significantly larger than the plain control, and the difference was evident with the increase in fiber content. The present study suggests that the specimen with 2% pineapple leaf fiber content can be used in normal environments due to its superior mechanical properties. However, one should be careful when using the material in marine environments.

Mechanical and Thermal Properties of Silane Treated Pineapple Leaf Fiber Reinforced Polylactic Acid Composites

2015 ◽  
Vol 659 ◽  
pp. 446-452 ◽  
Author(s):  
Supatra Pratumshat ◽  
Phutthachat Soison ◽  
Sukunya Ross
Keyword(s):  
Tensile Strength ◽  
Thermal Properties ◽  
Impact Strength ◽  
Fiber Content ◽  
Poly Lactic Acid ◽  
Mechanical And Thermal Properties ◽  
Silane Coupling Agents ◽  
Pineapple Leaf Fiber ◽  
Treated Fiber ◽  
Leaf Fiber

In this work, the mechanical and thermal properties of pineapple leaf fiber (PALF)/poly (lactic acid) (PLA) composites were studied. Pineapple leaf fibers were pretreated with 4 %wt sodium hydroxide solution followed by various silane solutions i.e. γ-(aminopropyl) trimethoxy silane (APS), γ-methacrylate propyl trimethoxy (A174) and bis [3-(triethoxysilyl) propyl] tetrasulfide (Si69). FTIR results show a significant functional groups of C=O and C=C of methacrylic group, NH2group and Si-O which are the characteristic of these silane coupling agents. SEM micrographs of pretreated PALF showed a rough surface while untreated and silane treated PALF revealed less roughness. It was found that the tensile strength at break of PLA is 56 MPa and tensile strength of composites decreased when fiber content increased. The tensile modulus of silane treated PALF composites were higher than PLA, whereas their impact strength were similar to PLA. Si69 treated PALF showed lower impact strength compared to the others silanes treated fiber which indicates more phase separation between fiber and matrix. This is related to high percentage of crystallinity of composite from Si69 treated fiber. It was also found that the addition of PALF did not change the glass transition temperature and melting temperature of PLA while the percentage of crystallinity increases as the fiber content increased. In addition WAXS study of composite from Si69 treated fiber reveals sharp crystalline peaks of PLA while the others silane treatments show amorphous characteristic of PLA.

scholarly journals Mechanical and Structural Characterization of Pineapple Leaf Fiber

Fibers ◽  
2021 ◽  
Vol 9 (8) ◽  
pp. 51
Author(s):  
Eric Worlawoe Gaba ◽  
Bernard O. Asimeng ◽  
Elsie Effah Kaufmann ◽  
Solomon Kingsley Katu ◽  
E. Johan Foster ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Crystallite Size ◽  
Alkali Treatment ◽  
X Ray ◽  
Pineapple Leaf Fiber ◽  
Hemicellulose Removal ◽  
Crystal Properties ◽  
Intermediate Bond ◽  
Leaf Fiber

Evidence-based research had shown that elevated alkali treatment of pineapple leaf fiber (PALF) compromised the mechanical properties of the fiber. In this work, PALF was subjected to differential alkali concentrations: 1, 3, 6, and 9% wt/wt to study the influence on the mechanical and crystal properties of the fiber. The crystalline and mechanical properties of untreated and alkali-treated PALF samples were investigated by X-ray diffractometry (XRD), Fourier transform infrared spectroscopy (FTIR), and tensile testing analysis. The XRD results indicated that crystal properties of the fibers were modified with 6% wt/wt alkali-treated PALF recording the highest crystallinity and crystallite size of 76% and 24 nm, respectively. The FTIR spectra suggested that all alkali-treated PALF samples underwent lignin and hemicellulose removal to varying degrees. An increase in the crystalline properties improved the mechanical properties of the PALF treated with alkali at 6% wt/wt, which has the highest tensile strength (1620 MPa). Although the elevated alkali treatment resulted in decreased mechanical properties of PALF, crystallinity generally increased. The findings revealed that the mechanical properties of PALF not only improve with increasing crystallinity and crystallite size, but are also dependent on the intermediate bond between adjacent cellulose chains.

Effect of Mastication Time on the Properties of Stearic Acid Coated Pineapple Leaf Fiber Reinforced Natural Rubber

2019 ◽  
Vol 824 ◽  
pp. 100-106
Author(s):  
Thapanee Wongpreedee ◽  
Karine Mougin ◽  
Taweechai Amornsakchai
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Stearic Acid ◽  
Natural Rubber ◽  
Average Diameter ◽  
Pineapple Leaf Fiber ◽  
Roll Mill ◽  
High Level ◽  
Acid Coating ◽  
Leaf Fiber

Pineapple leaf fiber (PALF) having an average diameter and length of about 4 μm and 6 mm, respectively, was used as reinforcing element for natural rubber (NR) composites. PALF was coated with different amount of stearic acid at 10, 30 and 50 wt% of PALF. PALF-NR composites containing two levels of PALF at 5 and 10 part per hundred rubber (phr) were prepared in a two roll mill. Mastication times of 2, 4 and 8 min were used. Tensile stress-strain curves and fracture surfaces of both untreated PALF and stearic acid coated PALF (SA-PALF) reinforced NR prepared with different mastication times were compared. At low level of PALF where aggregation was not a problem, stearic coating had adverse effect on mechanical properties due to the slippery PALF-rubber interface. At high level of PALF, the coating gave composites with higher tensile strength and strain at break. Moreover, tensile strength and strain at break increased with increasing mastication time. This indicates that stearic acid coating reduces the formation of PALF aggregations and allows PALF to work effectively.

scholarly journals Improvement in Mechanical Properties of Cantala Fiber and Short Cantala/Recycled High-Density Polyethylene Composite through Chemical Treatment

2017 ◽  
Author(s):  
Wijang Wisnu Raharjo ◽  
Rudy Soenoko ◽  
Yudy Surya Irawan ◽  
Agus Suprapto
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flexural Strength ◽  
Alkali Treatment ◽  
Amorphous Material ◽  
Tensile Modulus ◽  
Fiber Surface ◽  
Degree Of Crystallinity ◽  
Polyethylene Composite ◽  
Treated Fiber

The improvement of mechanical properties of cantala fiber and its composites. Treatments including alkali, silane, and the combination of both were carried out to modify the fiber surface. The influence of chemical treatments on fiber properties such as the degree of crystallinity and tensile strength was investigated. A variety of short cantala fiber reinforced rHDPE composites were produced by hot press, and the effect of fiber treatment on the flexural strength of composites was observed. SEM observations also carried out to highlight these changes. The result shows that alkali treatment improves tensile strength and tensile modulus of alkali treated fiber (NF12) which was predicted as a result of the enhancement of the cellulose crystallinity. In contrast, the tensile strength and tensile modulus of silane (SF05) and alkali-silane treated fiber (NSF05) decreased compared to untreated fiber (UF) which is caused by the addition of amorphous material. The tensile strength of alkali-silane treated fiber (NSF05) was lower than alkali treated fiber (NF12), but the composites prepared with NSF05 showed the highest increment of flexural strength of 25.9%. This may be due the combination of alkali and silane treatment helped in the better formation of fiber-matrix interface adhesion.

Sign in / Sign up

Export Citation Format

Share Document