scholarly journals The Comprehensive Comparison of Thermal and Physical-Mechanical Properties of the Recycled Rubber and Plastic Roofing Tiles versus Roofing Tiles Made with Different Traditional Materials

2018 ◽  
Vol 2018 ◽  
pp. 1-11
Author(s):  
Rosana Gaggino ◽  
Jerónimo Kreiker ◽  
Celina Filippín ◽  
María Paz Sánchez Amono ◽  
Julián González Laría ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Thermal Insulation ◽  
Lower Cost ◽  
Specific Weight ◽  
Thermal Transmittance ◽  
Comprehensive Comparison ◽  
Recycled Rubber ◽  
Recycled Plastics ◽  
Flexural Resistance

The objectives of this research were to estimate the thermal transmittance and some physical-mechanical properties of a housing cover built with roofing tiles made from recycled plastics and rubber and compare them with three other traditional solutions for housing cover: ceramic roofing tiles, concrete roofing tiles, and zinc sheets. This roofing tile has technical advantages over the others, due to its higher thermal insulation, higher resistance to freezing, higher resistance to hail, higher flexural resistance, lower specific weight, and lower water absorption, with lower cost than the traditional glazed black ceramic roofing tile. And it is also friendlier to the environment.

scholarly journals Characterization of Thermal Bio-Insulation Materials Based on Oil Palm Wood: The Effect of Hybridization and Particle Size

Polymers ◽  
2021 ◽  
Vol 13 (19) ◽  
pp. 3287
Author(s):  
Indra Mawardi ◽  
Sri Aprilia ◽  
Muhammad Faisal ◽  
Samsul Rizal
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Particle Size ◽  
Water Absorption ◽  
Thermal Insulation ◽  
Oil Palm ◽  
Bending Strength ◽  
Fine Particles ◽  
Biomass Waste ◽  
Insulation Materials

Oil palm wood is the primary biomass waste produced from plantations, comprising up to 70% of the volume of trunks. It has been used in non-structural materials, such as plywood, lumber, and particleboard. However, one aspect has not been disclosed, namely, its use in thermal insulation materials. In this study, we investigated the thermal conductivity and the mechanical and physical properties of bio-insulation materials based on oil palm wood. The effects of hybridization and particle size on the properties of the panels were also evaluated. Oil palm wood and ramie were applied as reinforcements, and tapioca starch was applied as a bio-binder. Panels were prepared using a hot press at a temperature of 150 °C and constant pressure of 9.8 MPa. Thermal conductivity, bending strength, water absorption, dimensional stability, and thermogravimetric tests were performed to evaluate the properties of the panels. The results show that hybridization and particle size significantly affected the properties of the panels. The density and thermal conductivity of the panels were in the ranges of 0.66–0.79 g/cm3 and 0.067–0.154 W/mK, respectively. The least thermal conductivity, i.e., 0.067 W/mK, was obtained for the hybrid panels with coarse particles at density 0.66 g/cm3. The lowest water absorption (54.75%) and thickness swelling (18.18%) were found in the hybrid panels with fine particles. The observed mechanical properties were a bending strength of 11.49–18.15 MPa and a modulus of elasticity of 1864–3093 MPa. Thermogravimetric analysis showed that hybrid panels had better thermal stability than pure panels. Overall, the hybrid panels manufactured with a coarse particle size exhibited better thermal resistance and mechanical properties than did other panels. Our results show that oil palm wood wastes are a promising candidate for thermal insulation materials.

Influence of the Granulometry of Organic Matter Ashes from Municipal Solid Waste on the Properties of Vitrified Ceramics

2005 ◽  
Vol 498-499 ◽  
pp. 552-557 ◽  
Author(s):  
Monica Castoldi Borlini Gadioli ◽  
B.C. Santos ◽  
R.A. Conte ◽  
Daltro Garcia Pinatti ◽  
Carlos Maurício Fontes Vieira ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
Organic Matter ◽  
Municipal Solid Waste ◽  
Water Absorption ◽  
Solid Waste ◽  
Mechanical Resistance ◽  
Potentially Toxic Metals ◽  
Flexural Resistance ◽  
High Degree

This work studies the influence of the granulometry of organic matter ashes from the municipal solid waste (MOL) on the mechanical properties of vitrified ceramics. Mixtures of clay with additions of the MOL ashes were prepared as vitrified ceramics. The degree of immobilization of the potentially toxic metals (PTM) contained in the ashes was then evaluated. Samples of a sedimentary clay with 13.5% of MOL ashes with granulometry, 35 and 200 mesh, were uniaxially pressed at 18 MPa and sintered at 1200°C. Results from 3- point flexural resistance and water absorption tests showed that the reduction in the particle size of the MOL ashes increased the mechanical resistance to 45 MPa while the water absorption reached 0.8%. These results and the high degree of immobilization of the PTM qualify the ceramic vitrification as an alternative to the final disposal of the MOL.

Experimentation and Analysis on Reinforced Basalt and Carbon Fibres Composite Laminate

2018 ◽  
Vol 1148 ◽  
pp. 12-20
Author(s):  
Vemu Vara Prasad
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Carbon Fibers ◽  
Lower Cost ◽  
Mechanical Tests ◽  
Absorption Capacity ◽  
Reinforced Composites ◽  
Basalt Fibre ◽  
Structural Applications ◽  
The Matrix

— The aim of the present work is to investigate the mechanical properties and water absorption capacity of carbon and basalt fibers mixed with epoxy. At present there is demand for natural friendly products. Basalt reinforced composites developed recently and these mineral amorphous fibres are a valid alternative to carbon fibers for their lower cost and to glass fibres for their strength. The present paper describes briefly on basalt and carbon fibers (unidirectional) which are used as reinforcement material for composites. The matrix epoxy (LY556-HY 951) is taken in to account to access to influence on the evaluated parameters. In order to use reinforced composites for structural applications, it is necessary to perform a mechanical characterization. With this aim experiments like tensile strength, flexural strength, hardness and water absorptions are performed. Later the mechanical properties obtained from experiments are compared with ANSYS software results. Keywords—Carbon fibre; Basalt fibre; Uni-directional fibres; Reinforcement, Mechanical Tests, Water Absorption Tests

Incorporation of Iraqi Rocks in the Production of Eco-Friendly Cement Mortar

2020 ◽  
Vol 38 (10A) ◽  
pp. 1522-1530
Author(s):  
Rawnaq S. Mahdi ◽  
Aseel B. AL-Zubidi ◽  
Hassan N. Hashim
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Compressive Strength ◽  
Water Absorption ◽  
Structural Properties ◽  
Mechanical Milling ◽  
Cement Mortar ◽  
Cement Mortars

This work reports on the incorporation of Flint and Kaolin rocks powders in the cement mortar in an attempt to improve its mechanical properties and produce an eco-friendly mortar. Flint and Kaolin powders are prepared by dry mechanical milling. The two powders are added separately to the mortars substituting cement partially. The two powders are found to improve the mechanical properties of the mortars. Hardness and compressive strength are found to increase with the increase of powders constituents in the cement mortars. In addition, the two powders affect water absorption and thermal conductivity of the mortar specimens which are desirable for construction applications. Kaolin is found to have a greater effect on the mechanical properties, water absorption, and thermal conductivity of the mortars than Flint. This behavior is discussed and analyzed based on the compositional and structural properties of the rocks powders.

scholarly journals Effects of Different Types of Fibers on the Physical and Mechanical Properties of MICP-Treated Calcareous Sand

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 268
Author(s):  
Jitong Zhao ◽  
Huawei Tong ◽  
Yi Shan ◽  
Jie Yuan ◽  
Qiuwang Peng ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Glass Fiber ◽  
Physical And Mechanical Properties ◽  
Polyester Fiber ◽  
Engineering Properties ◽  
Fiber Types ◽  
Calcite Precipitation ◽  
Calcareous Sand ◽  
Hemp Fiber

Microbial-induced calcite precipitation (MICP) has been a promising method to improve geotechnical engineering properties through the precipitation of calcium carbonate (CaCO3) on the contact and surface of soil particles in recent years. In the present experiment, water absorption and unconfined compressive strength (UCS) tests were carried out to investigate the effects of three different fiber types (glass fiber, polyester fiber, and hemp fiber) on the physical and mechanical properties of MICP-treated calcareous sand. The fibers used were at 0%, 0.10%, 0.15%, 0.20%, 0.25%, 0.30%, 0.35%, and 0.40% relative to the weight of the sand. The results showed that the failure strain and ductility of the samples could be improved by adding fibers. Compared to biocemented sand (BS), the water absorption of these three fiber-reinforced biocemented sands were, respectively, decreased by 11.60%, 21.18%, and 7.29%. UCS was, respectively, increased by 24.20%, 60.76%, and 6.40%. Polyester fiber produced the best effect, followed by glass fiber and hemp fiber. The optimum contents of glass fiber and polyester fiber were 0.20% and 0.25%, respectively. The optimum content of hemp fiber was within the range of 0.20–0.25%. Light-emitting diode (LED) microscope and scanning electron microscope (SEM) images lead to the conclusion that only a little calcite precipitation had occurred around the hemp fiber, leading to a poor bonding effect compared to the glass and polyester fibers. It was therefore suggested that polyester fiber should be used to improve the properties of biocemented sand.

scholarly journals Effects of a Twin-Screw Extruder Equipped with a Molten Resin Reservoir on the Mechanical Properties and Microstructure of Recycled Waste Plastic Polyethylene Pellet Moldings

Polymers ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 1058
Author(s):  
Hikaru Okubo ◽  
Haruka Kaneyasu ◽  
Tetsuya Kimura ◽  
Patchiya Phanthong ◽  
Shigeru Yao
Keyword(s):  
Mechanical Properties ◽  
Mechanical Performance ◽  
Value Added ◽  
Industrial Applications ◽  
Twin Screw Extruder ◽  
Screw Extruder ◽  
Polymer Properties ◽  
Wide Range ◽  
Twin Screw ◽  
Recycled Plastics

Each year, increasing amounts of plastic waste are generated, causing environmental pollution and resource loss. Recycling is a solution, but recycled plastics often have inferior mechanical properties to virgin plastics. However, studies have shown that holding polymers in the melt state before extrusion can restore the mechanical properties; thus, we propose a twin-screw extruder with a molten resin reservoir (MSR), a cavity between the screw zone and twin-screw extruder discharge, which retains molten polymer after mixing in the twin-screw zone, thus influencing the polymer properties. Re-extruded recycled polyethylene (RPE) pellets were produced, and the tensile properties and microstructure of virgin polyethylene (PE), unextruded RPE, and re-extruded RPE moldings prepared with and without the MSR were evaluated. Crucially, the elongation at break of the MSR-extruded RPE molding was seven times higher than that of the original RPE molding, and the Young’s modulus of the MSR-extruded RPE molding was comparable to that of the virgin PE molding. Both the MSR-extruded RPE and virgin PE moldings contained similar striped lamellae. Thus, MSR re-extrusion improved the mechanical performance of recycled polymers by optimizing the microstructure. The use of MSRs will facilitate the reuse of waste plastics as value-added materials having a wide range of industrial applications.

scholarly journals Effect of Organic Modifier Types on the Physical–Mechanical Properties and Overall Migration of Post-Consumer Polypropylene/Clay Nanocomposites for Food Packaging

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1502
Author(s):  
Eliezer Velásquez ◽  
Sebastián Espinoza ◽  
Ximena Valenzuela ◽  
Luan Garrido ◽  
María José Galotto ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Food Packaging ◽  
Clay Nanocomposites ◽  
Organic Modifier ◽  
Thermal And Mechanical Properties ◽  
Chemical Safety ◽  
Elongation At Break ◽  
Fatty Food ◽  
Recycled Plastics ◽  
Thermal Stability Of

The deterioration of the physical–mechanical properties and loss of the chemical safety of plastics after consumption are topics of concern for food packaging applications. Incorporating nanoclays is an alternative to improve the performance of recycled plastics. However, properties and overall migration from polymer/clay nanocomposites to food require to be evaluated case-by-case. This work aimed to investigate the effect of organic modifier types of clays on the structural, thermal and mechanical properties and the overall migration of nanocomposites based on 50/50 virgin and recycled post-consumer polypropylene blend (VPP/RPP) and organoclays for food packaging applications. The clay with the most hydrophobic organic modifier caused higher thermal stability of the nanocomposites and greater intercalation of polypropylene between clay mineral layers but increased the overall migration to a fatty food simulant. This migration value was higher from the 50/50 VPP/RPP film than from VPP. Nonetheless, clays reduced the migration and even more when the clay had greater hydrophilicity because of lower interactions between the nanocomposite and the fatty simulant. Conversely, nanocomposites and VPP/RPP control films exhibited low migration values in the acid and non-acid food simulants. Regarding tensile parameters, elongation at break values of PP film significantly increased with RPP addition, but the incorporation of organoclays reduced its ductility to values closer to the VPP.

scholarly journals Rational Design of Ag/ZnO Hybrid Nanoparticles on Sericin/Agarose Composite Film for Enhanced Antimicrobial Applications

2020 ◽  
Vol 22 (1) ◽  
pp. 105
Author(s):  
Wanting Li ◽  
Zixuan Huang ◽  
Rui Cai ◽  
Wan Yang ◽  
Huawei He ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Antimicrobial Activity ◽  
Composite Film ◽  
Water Absorption ◽  
Rational Design ◽  
Hybrid Nanoparticles ◽  
Gram Negative Bacteria ◽  
Gram Positive ◽  
Gram Negative ◽  
X Ray

Silver-based hybrid nanomaterials are receiving increasing attention as potential alternatives for traditional antimicrobial agents. Here, we proposed a simple and eco-friendly strategy to efficiently assemble zinc oxide nanoparticles (ZnO) and silver nanoparticles (AgNPs) on sericin-agarose composite film to impart superior antimicrobial activity. Based on a layer-by-layer self-assembly strategy, AgNPs and ZnO were immobilized on sericin-agarose films using the adhesion property of polydopamine. Scanning electron microscopy, energy-dispersive X-ray spectroscopy, and X-ray powder diffraction spectroscopy were used to show the morphology of AgNPs and ZnO on the surface of the composite film and analyze the composition and structure of AgNPs and ZnO, respectively. Water contact angle, swelling ratio, and mechanical property were determined to characterize the hydrophilicity, water absorption ability, and mechanical properties of the composite films. In addition, the antibacterial activity of the composite film was evaluated against Gram-positive and Gram-negative bacteria. The results showed that the composite film not only has desirable hydrophilicity, high water absorption ability, and favorable mechanical properties but also exhibits excellent antimicrobial activity against both Gram-positive and Gram-negative bacteria. It has shown great potential as a novel antimicrobial biomaterial for wound dressing, artificial skin, and tissue engineering.

scholarly journals Effect of Water Ingress on the Mechanical and Chemical Properties of Polybutylene Terephthalate Reinforced with Glass Fibers

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1261
Author(s):  
Catarina S. P. Borges ◽  
Alireza Akhavan-Safar ◽  
Eduardo A. S. Marques ◽  
Ricardo J. C. Carbas ◽  
Christoph Ueffing ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Water Uptake ◽  
Significant Influence ◽  
Water Immersion ◽  
Water Diffusion ◽  
Polybutylene Terephthalate ◽  
Chemical Changes ◽  
Water Ingress ◽  
Effect Of Water

Short fiber reinforced polymers are widely used in the construction of electronic housings, where they are often exposed to harsh environmental conditions. The main purpose of this work is the in-depth study and characterization of the water uptake behavior of PBT-GF30 (polybutylene terephthalate with 30% of short glass fiber)as well as its consequent effect on the mechanical properties of the material. Further analysis was conducted to determine at which temperature range PBT-GF30 starts experiencing chemical changes. The influence of testing procedures and conditions on the evaluation of these effects was analyzed, also drawing comparisons with previous studies. The water absorption behavior was studied through gravimetric tests at 35, 70, and 130 °C. Fiber-free PBT was also studied at 35 °C for comparison purposes. The effect of water and temperature on the mechanical properties was analyzed through bulk tensile tests. The material was tested for the three temperatures in the as-supplied state (without drying or aging). Afterwards, PBT-GF30 was tested at room temperature following water immersion at the three temperatures. Chemical changes in the material were also analyzed through Fourier-transform infrared spectroscopy (FTIR). It was concluded that the water diffusion behavior is Fickian and that PBT absorbs more water than PBT-GF30 but at a slightly higher rate. However, temperature was found to have a more significant influence on the rate of water diffusion of PBT-GF30 than fiber content did. Temperature has a significant influence on the mechanical properties of the material. Humidity contributes to a slight drop in stiffness and strength, not showing a clear dependence on water uptake. This decrease in mechanical properties occurs due to the relaxation of the polymeric chain promoted by water ingress. Between 80 and 85 °C, after water immersion, the FTIR profile of the material changes, which suggests chemical changes in the PBT. The water absorption was simulated through heat transfer analogy with good results. From the developed numerical simulation, the minimum plate size to maintain the water ingress unidirectional was 30 mm, which was validated experimentally.

Sign in / Sign up

Export Citation Format

Share Document