scholarly journals Thermoelasticity Coupling Transient Response of Composite-Material Direction Pipe

2018 ◽  
Vol 2018 ◽  
pp. 1-10
Author(s):  
Jian-lin Zhong ◽  
Jie Ren ◽  
Da-wei Ma
Keyword(s):  
Composite Material ◽  
Temperature Field ◽  
Transient Response ◽  
Thermal Load ◽  
Dynamic Pressure ◽  
Element Model ◽  
Jet Flow ◽  
Unsteady Temperature ◽  
Positive Scheme ◽  
Main Factor

Based on the positive scheme method, the thermal load of the jet flow in an inner composite-material direction pipe is obtained, and the thermoelasticity coupling transient response is investigated. The positive scheme method with second-order accuracy is extended for solving the axisymmetric Euler equations, and the supersonic axisymmetric jet flow over a missile afterbody containing jet exhaust is simulated. The correctness of the development for the positive scheme method is verified. With the developed positive scheme method used to simulate the jet flow in the inner direction pipe, the thermal load is obtained. The thermoelasticity coupling finite element model of the composite-material direction pipe is established, and the stress response under dynamic pressure, unsteady temperature, and coupling state is obtained. Results show that, at the beginning of engine ignition, the effect of dynamic pressure and temperature field on the coupling stress is basically the same, and after that, the contribution of the temperature field to the coupling stress increases, and the thermal stress is the main factor affecting the strength of the composite-material direction pipe.

Study on Unsteady Temperature Field of Diesel Engine Piston

2013 ◽  
Vol 779-780 ◽  
pp. 965-970
Author(s):  
You Liu ◽  
Jing Jing Liu ◽  
Xiao Chen
Keyword(s):  
Temperature Field ◽  
Temperature Fluctuation ◽  
Extreme Temperature ◽  
Temperature Fluctuations ◽  
Cold Start ◽  
Element Model ◽  
Unsteady Temperature ◽  
Unsteady Temperature Field ◽  
Calculate Temperature Field ◽  
Transient Thermal

The paper took the piston of 620 single-cylinder engine as an example,a finite element model of piston was built with the help of ANSYS software. Than to calculate temperature field and and quick cold start conditions respectively[1]. Through the periodic transient thermal analysis, temperature fluctuations on the surface of the piston were derived, which indicated that the surface contacted with gas was the main temperature fluctuation area. The max temperature fluctuation can be up to 20 ° C and the wild fluctuation occurred in a distance of 2 mm from the surface of the piston. Temperatures of the piston went up according to exponential rule during the course of quick cold start, Extreme temperature fluctuations will generate huge quasi-static thermal stress.

ANSYS Analysis of Heat Model for the Electromagnetic Drying Cylinder

2012 ◽  
Vol 268-270 ◽  
pp. 916-920
Author(s):  
Zheng Shun Wang ◽  
Wen Jia Han
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Thermal Load ◽  
Geometric Model ◽  
Element Model ◽  
Actual Situation ◽  
Ansys Software ◽  
Software Applications ◽  
Ansys Analysis ◽  
Drying Cylinder

In this thesis, the process of electromagnetic drying cylinder was analyzed creating by the dryer finite element model using ANSYS. The conduction thermal analysis, the applied load and solved showed the results of three major components. Which create a finite element model of the process, mainly the preprocessor using ANSYS software to create or import geometric models from other software applications, and then add the material properties. The last of the geometric model meshing and solving process need to enter solvers according to the actual situation. The setting is applied to the thermal load and conditions. Then it is proceed to the finite element solution operator. It final usually the Post 1, or Post2 view results, and based on our experience to judge correctly

scholarly journals Unsteady temperature field calculation in the exothermic reaction

2021 ◽  
Vol 1791 (1) ◽  
pp. 012072
Author(s):  
S V Fedorov ◽  
A S Tolstukha ◽  
I V Fedorov ◽  
V V Zhukovskyy
Keyword(s):  
Temperature Field ◽  
Exothermic Reaction ◽  
Field Calculation ◽  
Unsteady Temperature ◽  
Unsteady Temperature Field

Free Vibration Analysis for Tapered Cross-Section Steel-Concrete Composite Material Beam

2017 ◽  
Vol 893 ◽  
pp. 380-383
Author(s):  
Jun Xia ◽  
Z. Shen ◽  
Kun Liu
Keyword(s):  
Finite Element ◽  
Composite Material ◽  
Cross Section ◽  
Vibration Analysis ◽  
Free Vibration Analysis ◽  
Element Model ◽  
Composite Beams ◽  
Shear Connection ◽  
The Common ◽  
Interlayer Slip

The tapered cross-section beams made of steel-concrete composite material are widely used in engineering constructions and their dynamic behavior is strongly influenced by the type of shear connection jointing the two different materials. The 1D high order finite element model for tapered cross-section steel-concrete composite material beam with interlayer slip was established in this paper. The Numerical results for vibration nature frequencies of the composite beams with two typical boundary conditions were compared with ANSYS using 2D plane stress element. The 1D element is more efficient and economical for the common tapered cross-section steel-concrete composite material beams in engineering.

Model Development of the Application of Finite Element – Eigenvalue Method to the Determination of Transient Temperature Field in Functionally Graded Materials

2007 ◽  
Vol 18-19 ◽  
pp. 253-261
Author(s):  
John A. Akpobi ◽  
C.O. Edobor
Keyword(s):  
Finite Element ◽  
Temperature Field ◽  
Functionally Graded Materials ◽  
Model Development ◽  
Element Model ◽  
Steady State Solution ◽  
Functionally Graded ◽  
Transient Temperature ◽  
Graded Materials ◽  
Eigenvalue Method

In this paper, a finite elment-eigenvalue method is formulated to solve the finite element models of time dependent temperature field problems in non-homogeneous materials such as functionally graded materials (FGMs). The method formulates an eigenvalue problem from the original finite element model and proceeds to calculate the associated eigenvectors from which the solution can be obtained. The results obtained highly accurate and are exponential functions of time which when compared with the exact solution tended fast to the steady state solution.

A Study on Process-Induced Warpage of Curing Mold of Composite Structures

2009 ◽  
Vol 79-82 ◽  
pp. 1173-1176
Author(s):  
Guang Quan Yue ◽  
Bo Ming Zhang ◽  
Shan Yi Du ◽  
Fu Hong Dai ◽  
Cheng Zhang ◽  
...  
Keyword(s):  
Thermal Load ◽  
Composite Structures ◽  
Three Dimensional ◽  
Element Model ◽  
Coupling Problem ◽  
Dimensional Precision ◽  
Numerical Predictions ◽  
Dimensional Finite Element ◽  
Thermosetting Composite ◽  
Three Dimensional Finite Element

Framed curing mold is subjected to an uneven thermal load, gravity force and the pressures from composite parts and auxiliary tools during autoclave processing of thermosetting composite structures. And those loads induce the warpage of framed-mold. The warpage of framed-mold during autoclave processing influences dimensional precision of composite parts. In the present work, a three-dimensional finite element model for prediction of the warpage of framed-mold during autoclave processing has been developed. This model solved the coupling problem between the deformation and the temperature distribution of framed-mold and allows analysis of all major identified deformation influencing factors. And numerical predictions compare quite well with experimental measurements. A parametric study was performed using FEM program to examine the effect of varying the thickness of framed-mold, the shape and the dimension of mold vents.

Sign in / Sign up

Export Citation Format

Share Document