scholarly journals The Visual and Quantitative Study of the Microoccurrence of Irreducible Water at the Pore and Throat System in a Low-Permeability Sandstone Reservoir by Using Microcomputerized Tomography

Geofluids ◽  
2018 ◽  
Vol 2018 ◽  
pp. 1-14 ◽  
Author(s):  
Xiaoyu Gu ◽  
Chunsheng Pu ◽  
Hai Huang ◽  
Nasir Khan ◽  
Jing Liu ◽  
...  

The microflow equipment monitored with micro X-ray computerized tomography (CT) is employed to investigate the microoccurrence of the irreducible water in a low-permeability sandstone core. By means of image segmentation and the three-dimensional (3D) image reconstruction technique, the visual microdistribution characteristics of irreducible water in two-dimensional (2D) slices and the 3D pore-throat system are quantitatively evaluated. Some interesting findings are list as below. Firstly, due to the variant micro geometric structures of the pore-throat systems, specific core slices showed significantly different irreducible water saturation even though these slices had same areal porosity. Secondly, due to the influence of capillary trapping and the existence of oil-wetting clay (main chlorite), the irreducible water saturation in the throat system (64%) is much larger than that in the pore system (36%). Furthermore, the wetting phase (irreducible water) did not spread all over the surface of the pore-throat network which caused a much more complicated oil-water two-phase interface. Thirdly, in micro scale, the main irreducible water occurrence mode in the pore system is much different from that in the throat system. In the pore system, the irreducible water principally existed in the corner of the pores which are linked through a water film. While in the throat system, the irreducible water occurrence is dominated by the water film. However, 25.5% of the throats are blocked by the irreducible water which cut off the crude oil drainage channels.

1985 ◽  
Vol 25 (06) ◽  
pp. 945-953 ◽  
Author(s):  
Mark A. Miller ◽  
H.J. Ramey

Abstract Over the past 20 years, a number of studies have reported temperature effects on two-phase relative permeabilities in porous media. Some of the reported results, however, have been contradictory. Also, observed effects have not been explained in terms of fundamental properties known to govern two-phase flow. The purpose of this study was to attempt to isolate the fundamental properties affecting two-phase relative permeabilities at elevated temperatures. Laboratory dynamic-displacement relative permeability measurements were made on unconsolidated and consolidated sand cores with water and a refined white mineral oil. Experiments were run on 2-in. [5.1-cm] -diameter, 20-in. [52.-cm] -long cores from room temperature to 300F [149C]. Unlike previous researchers, we observed essentially no changes with temperature in either residual saturations or relative permeability relationships. We concluded that previous results may have been affected by viscous previous results may have been affected by viscous instabilities, capillary end effects, and/or difficulties in maintaining material balances. Introduction Interest in measuring relative permeabilities at elevated temperatures began in the 1960's with petroleum industry interest in thermal oil recovery. Early thermal oil recovery field operations (well heaters, steam injection, in-situ combustion) indicated oil flow rate increases far in excess of what was predicted by viscosity reductions resulting from heating. This suggested that temperature affects relative permeabilities. One of the early studies of temperature effects on relative permeabilities was presented by Edmondson, who performed dynamic displacement measurements with crude performed dynamic displacement measurements with crude and white oils and distilled water in Berea sandstone cores. Edmondson reported that residual oil saturations (ROS's) (at the end of 10 PV's of water injected) decreased with increasing temperature. Relative permeability ratios decreased with temperature at high water saturations but increased with temperature at low water saturations. A series of elevated-temperature, dynamic-displacement relative permeability measurements on clean quartz and "natural" unconsolidated sands were reported by Poston et al. Like Edmondson, Poston et al. reported a decrease in the "practical" ROS (at less than 1 % oil cut) as temperature increased. Poston et al. also reported an increase in irreducible water saturation. Although irreducible water saturations decreased with decreasing temperature, they did not revert to the original room temperature values. It was assumed that the cores became increasingly water-wet with an increase in both temperature and time; measured changes of the IFT and the contact angle with temperature increase, however, were not sufficient to explain observed effects. Davidson measured dynamic-displacement relative permeability ratios on a coarse sand and gravel core with permeability ratios on a coarse sand and gravel core with white oil displaced by distilled water, nitrogen, and superheated steam at temperatures up to 540F [282C]. Starting from irreducible water saturation, relative permeability ratio curves were similar to Edmondson's. permeability ratio curves were similar to Edmondson's. Starting from 100% oil saturation, however, the curves changed significantly only at low water saturations. A troublesome aspect of Davidson's work was that he used a hydrocarbon solvent to clean the core between experiments. No mention was made of any consideration of wettability changes, which could explain large increases in irreducible water saturations observed in some runs. Sinnokrot et al. followed Poston et al.'s suggestion of increasing water-wetness and performed water/oil capillary pressure measurements on consolidated sandstone and limestone cores from room temperature up to 325F [163C]. Sinnokrot et al confirmed that, for sandstones, irreducible water saturation appeared to increase with temperature. Capillary pressures increased with temperature, and the hysteresis between drainage and imbibition curves reduced to essentially zero at 300F [149C]. With limestone cores, however, irreducible water saturations remained constant with increase in temperature, as did capillary pressure curves. Weinbrandt et al. performed dynamic displacement experiments on small (0.24 to 0.49 cu in. [4 to 8 cm3] PV) consolidated Boise sandstone cores to 175F [75C] PV) consolidated Boise sandstone cores to 175F [75C] with distilled water and white oil. Oil relative permeabilities shifted toward high water saturations with permeabilities shifted toward high water saturations with increasing temperature, while water relative permeabilities exhibited little change. Weinbrandt et al. confirmed the findings of previous studies that irreducible water saturation increases and ROS decreases with increasing temperature. SPEJ P. 945


Author(s):  
Mahmoud Leila ◽  
Ali Eslam ◽  
Asmaa Abu El-Magd ◽  
Lobna Alwaan ◽  
Ahmed Elgendy

Abstract The Messinian Abu Madi Formation represents the most prospective reservoir target in the Nile Delta. Hydrocarbon exploration endeavors in Nile Delta over the last few decades highlighted some uncertainties related to the predictability and distribution of the Abu Madi best reservoir quality facies. Therefore, this study aims at delineating the factors controlling the petrophysical heterogeneity of the Abu Madi reservoir facies in Faraskour Field, northeastern onshore part of the Nile Delta. This work provides the very first investigation on the reservoir properties of Abu Madi succession outside the main canyon system. In the study area, Abu Madi reservoir is subdivided into two sandstone units (lower fluvial and upper estuarine). Compositionally, quartzose sandstones (quartz > 65%) are more common in the fluvial unit, whereas the estuarine sandstones are often argillaceous (clays > 15%) and glauconitic (glauconite > 10%). The sandstones were classified into four reservoir rock types (RRTI, RRTII, RRTIII, and RRTIV) having different petrophysical characteristics and fluid flow properties. RRTI hosts the quartzose sandstones characterized by mega pore spaces (R35 > 45 µm) and a very well-connected, isotropic pore system. On the other side, RRTIV constitutes the lowest reservoir quality argillaceous sandstones containing meso- and micro-sized pores (R35 > 5 µm) and a pore system dominated by dead ends. Irreducible water saturation increases steadily from RRTI (Swir ~ 5%) to RRTIV (Swir > 20%). Additionally, the gas–water two-phase co-flowing characteristics decrease significantly from RRTI to RRTIV facies. The gaseous hydrocarbons will be able to flow in RRTI facies even at water saturation values exceeding 90%. On the other side, the gas will not be able to displace water in RRTIV sandstones even at water saturation values as low as 40%. Similarly, the influence of confining pressure on porosity and permeability destruction significantly increases from RRTI to RRTIV. Accordingly, RRTI facies are the best reservoir targets and have high potentiality for primary porosity preservation.


2014 ◽  
Vol 1010-1012 ◽  
pp. 1676-1683 ◽  
Author(s):  
Bin Li ◽  
Wan Fen Pu ◽  
Ke Xing Li ◽  
Hu Jia ◽  
Ke Yu Wang ◽  
...  

To improve the understanding of the influence of effective permeability, reservoir temperature and oil-water viscosity on relative permeability and oil recovery factor, core displacement experiments had been performed under several experimental conditions. Core samples used in every test were natural cores that came from Halfaya oilfield while formation fluids were simulated oil and water prepared based on analyze data of actual oil and productive water. Results from the experiments indicated that the shape of relative permeability curves, irreducible water saturation, residual oil saturation, width of two-phase region and position of isotonic point were all affected by these factors. Besides, oil recovery and water cut were also related closely to permeability, temperature and viscosity ratio.


SPE Journal ◽  
2016 ◽  
Vol 21 (06) ◽  
pp. 1970-1980 ◽  
Author(s):  
Mahmood Reza Yassin ◽  
Hassan Dehghanpour ◽  
James Wood ◽  
Qing Lan

Summary Recent studies show that the pore network of unconventional rocks, such as gas shales, generally consists of inorganic and organic parts. The organic part is strongly oil-wet and preferentially imbibes the oleic phase. In contrast, the inorganic part is usually hydrophilic and preferentially imbibes the aqueous phase. Conventional theories of relative permeability, which are based on uniform wettability, cannot be applied to determine phase permeability in unconventional rocks with dual-wettability behavior. The objective of this paper is to extend the previous theories to model relative permeability of dual-wettability systems in which oleic and aqueous phases can both act as wetting phases in hydrophobic and hydrophilic pore networks, respectively. In the first part of the paper, we review and discuss the results of scanning electron microscopy (SEM), organic petrography, mercury injection capillary pressure (MICP), and comparative water/oil imbibition experiments conducted on several samples from the Triassic Montney tight gas siltstone play of the Western Canadian Sedimentary Basin. We also discuss various crossplots to understand the reasons behind the observed dual-wettability behavior, and to investigate the spatial distribution and morphology of hydrophilic and hydrophobic pores. In the second part, Purcell's model (Purcell 1949) is extended to develop a conceptual model for relative permeability of gas and water in a dual-wettability system such as the Montney tight gas formation. Finally, the proposed model is compared with measured relative permeability data. The results suggest that the submicron pores within solid bitumen/pyrobitumen are strongly water-repellant; therefore, they prefer gas over water under different saturation conditions. This part of the pore network is usually represented by a long tail at the lower end of the pore-throat-size distribution determined from MICP. The proposed relative permeability model describes single-phase flow of gas through the tail part, and two-phase flow of gas and water through the remaining bell-shaped part of the pore-throat-size distribution, which dominantly represents inorganic micropores. On the basis of our model, by increasing the fraction of water-repellant submicron pores, gas relative permeability decreases for a fixed water saturation. This decrease is ascribed to the reduction of the average size of flow conduits for the gas phase.


Lithosphere ◽  
2021 ◽  
Vol 2021 (Special 4) ◽  
Author(s):  
Qi Lisha ◽  
Jiang Zhibin ◽  
Wang Xiaowei ◽  
Wang Jie ◽  
Qian Chuanchuan

Abstract The microscopic pore structure characteristics and the oil-water two-phase seepage law in the low permeability sandstone reservoir in Mobei oilfield in Junggar Basin were analyzed through laboratory experiments. The results of mercury pressure, constant velocity mercury pressure, thin slice of casting, and CT scan analyses showed that the reservoir had strong microheterogeneity with the presence of local large channels. The large channel had a small volume but considerably contributed to the permeability, which played a crucial role in the reservoir seepage. The relative permeability curve showed that with the increase of water saturation, the relative permeability of the oil phase decreased rapidly; the water phase relative permeability of glutenite, gravel-bearing sandstone, and coarse sandstone increased slightly; and the water cut increased rapidly. The relative permeability of the water phase of medium and fine sandstone increased, the water cut increased rapidly, and the residual oil saturation was high. In the process of core displacement, on-line CT scanning monitoring showed that before the breakthrough of the water drive front, the oil saturation decreased greatly along the way. After the breakthrough of the water drive front, the water cut increased rapidly and directly entered the ultrahigh water cut stage. Owing to the serious heterogeneity of the micropore structure, the fingering phenomenon was obvious in the process of displacement.


Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
Jin Yan ◽  
Rongchen Zheng ◽  
Peng Chen ◽  
Shuping Wang ◽  
Yunqing Shi

During the development of tight gas reservoir, the irreducible water saturation, rock permeability, and relative permeability change with formation pressure, which has a significant impact on well production. Based on capillary bundle model and fractal theory, the irreducible water saturation model, permeability model, and relative permeability model are constructed considering the influence of water film and stress sensitivity at the same time. The accuracy of this model is verified by results of nuclear magnetic experiment and comparison with previous models. The effects of some factors on irreducible water saturation, permeability, and relative permeability curves are discussed. The results show that the stress sensitivity will obviously reduce the formation permeability and increase the irreducible water saturation, and the existence of water film will reduce the permeability of gas phase. The increase of elastic modulus weakens the stress sensitivity of reservoir. The irreducible water saturation increases, and the relative permeability curve changes little with the increase of effective stress. When the minimum pore radius is constant, the ratio of maximum pore radius to minimum pore radius increases, the permeability increases, the irreducible water saturation decreases obviously, and the two-phase flow interval of relative permeability curve increases. When the displacement pressure increases, the irreducible water saturation decreases, and the interval of two-phase flow increases. These models can calculate the irreducible water saturation, permeability and relative permeability curves under any pressure in the development of tight gas reservoir. The findings of this study can help for better understanding of the productivity evaluation and performance prediction of tight sandstone gas reservoirs.


Fractals ◽  
2020 ◽  
Vol 28 (01) ◽  
pp. 2050012
Author(s):  
JINGANG FU ◽  
YULIANG SU ◽  
LEI LI ◽  
YONGMAO HAO ◽  
WENDONG WANG

A novel predictive model for calculating relative permeability was derived based on a capillary tube model with fractal theory. Different forms of immovable water including water film (WF) and microcapillary water were incorporated in the new model. Special immovable water called lost dynamic water (LDW) was introduced in the proposed model. The results of verification show that there is agreement between the calculated results and the published experimental data and analytical model. The results indicated that the effect of LDW, WF, and stress dependence had a significant influence on the relative permeability, which cannot be neglected. A larger LDW coefficient, more dead-end pores, and corners in porous media yielded a more complex pore structure. Therefore, more water was trapped in the pore and became connate water, resulting in higher gas relative permeability and lower water relative permeability at a given water saturation. Due to the microcapillary effect, the relative permeability of the water/gas increased/decreased as the drawdown pressure increased at the same water saturation. Higher effective stress was more likely to cause rock deformation, resulting in higher gas relative permeability and lower water relative permeability at a given water saturation. This study provides a significant reference for reservoir engineers conducting water and gas two-phase flow analysis. The theoretical model is beneficial for research into the interpolation of relative permeability via numerical simulation.


SPE Journal ◽  
2021 ◽  
pp. 1-19
Author(s):  
Tao Zhang ◽  
Farzam Javadpour ◽  
Jing Li ◽  
Yulong Zhao ◽  
Liehui Zhang ◽  
...  

Summary The transport behaviors of both single-phase gas and single-phase water at nanoscale deviate from the predictions of continuum flow theory. The deviation is greater and more complex when both gas and liquid flow simultaneously in a pore or network of pores. We developed a pseudopotential-based lattice Boltzmann (LB) method (LBM) to simulate gas/water two-phase flow at pore scale. A key element of this LBM is the incorporation of fluid/fluid and fluid/solid interactions that successfully capture the microscopic interactions among phases. To calibrate the model, we simulated a series of simple and static nanoscale two-phase systems, including phase separation, a Laplace bubble, contact angle, and a static nanoconfined bubble. In this work, we demonstrate the use of our proposed LBM to model gas/water two-phase flow in systems like a single nanopore, two parallel nanopores, and nanoporous media. Our LBM simulations of static water-film and gas-film scenarios in nanopores agree well with the theory of disjoining pressure and serve as critical steps toward validating this approach. This work highlights the importance of interfacial forces in determining static and dynamic fluid behaviors at the nanoscale. In the Applications section, we determine the water-film thickness and disjoining pressure in a hydrophilic nanopore under the drainage process. Next, we model water imbibition into gas-filled parallel nanopores with different wettability, and simulate gas/water two-phase flow in dual-wettability nanoporous media. The results showed that isolated patches of organic matters (OMs) impede water flow, and the water relative permeability curve cuts off at water saturation [= 1–volumetric total organic carbon (TOC)]. The residual gas saturation is also controlled by the volumetric TOC, ascribed to the isolation of organic patches by the saturating water; therefore, the gas relative permeability curve cuts off at water saturation (= 1–volumetric TOC).


Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-14
Author(s):  
Cheng Lu ◽  
Xuwen Qin ◽  
Lu Yu ◽  
Lantao Geng ◽  
Wenjing Mao ◽  
...  

Many hydrate-bearing sediments in the Shenhu area of the South China Sea are featured with unconsolidated clayed silt, small particle size, and high content of clay, which can pose a great challenge for gas production. In order to investigate the gas-water relative permeability in clay-silt sediments, through a radial flow experiment, samples from the target sediment in the Shenhu area were selected and studied. The results show that the irreducible water saturation is high and the influence of the gas-water interaction is obvious. The relative permeability analysis shows that the two-phase flow zone is narrow and maximum gas relative permeability is below 0.1. The flow pattern in clay-silt sediment is more complicated, and the existing empirical models are inadequate for flow characterization. The depressurization method to extract a hydrate reservoir with clay-silt sediments faces the problem of insufficient production capacity. Compared with the ordinary hydrate reservoir with sandstone sediment, the hydrate reservoir with clay-silt sediment has a low permeability and poor gas flow capacity. The gas-water ratio abnormally decreases during the production. It is urgent to enhance production with cost-effective measures.


Sign in / Sign up

Export Citation Format

Share Document