scholarly journals An Effective Pt-Cu/SiO2 Catalyst for the Selective Hydrogenation of Cinnamaldehyde

2018 ◽  
Vol 2018 ◽  
pp. 1-7 ◽  
Author(s):  
Dong Wang ◽  
Yujun Zhu
Keyword(s):  
Selective Hydrogenation ◽  
Catalytic Performance ◽  
Impregnation Method ◽  
Cinnamyl Alcohol ◽  
Bimetal Catalyst

The bimetal catalyst Pt-Cu/SiO2 was prepared by the impregnation method. Its catalytic performance was investigated by the selective hydrogenation of cinnamaldehyde. Pt-Cu/SiO2 exhibited much higher selectivity (64.1%) to cinnamyl alcohol than Pt/SiO2 (3.7%), while they showed similar conversion of cinnamaldehyde. This enhancement was attributed to the increase in the amount of the Pt0 species on the Pt-Cu/SiO2 surface, which is derived from the interaction between Pt and Cu revealed by XRD and XPS.

scholarly journals Effect of Carbon Supported Pt Catalysts on Selective Hydrogenation of Cinnamaldehyde

2016 ◽  
Vol 2016 ◽  
pp. 1-9 ◽  
Author(s):  
Qing Han ◽  
Yunfei Liu ◽  
Dong Wang ◽  
Fulong Yuan ◽  
Xiaoyu Niu ◽  
...  
Keyword(s):  
Selective Hydrogenation ◽  
Impregnation Method ◽  
Pt Catalysts ◽  
Cinnamyl Alcohol ◽  
Electronic Effects ◽  
Carbon Supports ◽  
Graphene Oxides ◽  
Graphitization Degree ◽  
Supported Pt Catalysts ◽  
Reduced Graphene

Selective hydrogenation of cinnamaldehyde (CAL) to cinnamyl alcohol (COL) is of both fundamental and industrial interest. It is of great significance to evaluate the possible differences between different supports arising from metal dispersion and electronic effects, in terms of activity and selectivity. Herein, Pt catalysts on different carbon supports including carbon nanotubes (CNTs) and reduced graphene oxides (RGO) were developed by a simple wet impregnation method. The resultant catalysts were well characterized by XRD, Raman, N2physisorption, TEM, and XPS analysis. Applied in the hydrogenation of cinnamaldehyde, 3.5 wt% Pt/CNT shows much higher selectivity towards cinnamyl alcohol (62%) than 3.5 wt% Pt/RGO@SiO2(48%). The enhanced activity can be ascribed to the high graphitization degree of CNTs and high density of dispersed Pt electron cloud.

Structural/Texture Evolution During Facile Substitution of Ni into ZSM-5 Nanostructure vs. its Impregnation Dispersion Used in Selective Transformation of Methanol to Ethylene and Propylene

2020 ◽  
Vol 23 ◽  
Author(s):  
Parisa Sadeghpour ◽  
Mohammad Haghighi ◽  
Mehrdad Esmaeili
Keyword(s):  
High Temperature ◽  
Physicochemical Properties ◽  
Active Sites ◽  
Catalytic Performance ◽  
Fixed Bed Reactor ◽  
Light Olefins ◽  
Isomorphous Substitution ◽  
Impregnation Method ◽  
Hydrothermal Temperature ◽  
X Ray

Aim and Objective: Effect of two different modification methods for introducing Ni into ZSM-5 framework was investigated under high temperature synthesis conditions. The nickel successfully introduced into the MFI structures at different crystallization conditions to enhance the physicochemical properties and catalytic performance. Materials and Methods: A series of impregnated Ni/ZSM-5 and isomorphous substituted NiZSM-5 nanostructure catalysts were prepared hydrothermally at different high temperatures and within short times. X-ray diffraction (XRD), Field emission scanning electron microscopy (FESEM), Energy dispersive X-ray (EDX), Brunner, Emmett and Teller-Barrett, Joyner and Halenda (BET-BJH), Fourier transform infrared (FTIR) and Temperature-programmed desorption of ammonia (TPDNH3) were applied to investigate the physicochemical properties. Results: Although all the catalysts showed pure silica MFI–type nanosheets and coffin-like morphology, using the isomorphous substitution for Ni incorporation into the ZSM-5 framework led to the formation of materials with lower crystallinity, higher pore volume and stronger acidity compared to using impregnation method. Moreover, it was found that raising the hydrothermal temperature increased the crystallinity and enhanced more uniform incorporation of Ni atoms in the crystalline structure of catalysts. TPD-NH3 analysis demonstrated that high crystallization temperature and short crystallization time of NiZSM-5(350-0.5) resulted in fewer weak acid sites and medium acid strength. The MTO catalytic performance was tested in a fixed bed reactor at 460ºC and GHSV=10500 cm3 /gcat.h. A slightly different reaction pathway was proposed for the production of light olefins over impregnated Ni/ZSM-5 catalysts based on the role of NiO species. The enhanced methanol conversion for isomorphous substituted NiZSM-5 catalysts could be related to the most accessible active sites located inside the pores. Conclusion: The impregnated Ni/ZSM-5 catalyst prepared at low hydrothermal temperature showed the best catalytic performance, while the isomorphous substituted NiZSM-5 prepared at high temperature was found to be the active molecular sieve regarding the stability performance.

Effects of impregnation solvent and reduction temperature on the catalytic performance of Pd/Al2O3 in the selective hydrogenation of 1,3-butadiene

2011 ◽  
Vol 103 (2) ◽  
pp. 405-417 ◽  
Author(s):  
Kanda Pattamakomsan ◽  
Francisco Jose Cadete Santos Aires ◽  
Kongkiate Suriye ◽  
Joongjai Panpranot
Keyword(s):  
Selective Hydrogenation ◽  
Catalytic Performance ◽  
Reduction Temperature

CO2 valorization into synthetic natural gas (SNG) using a Co–Ni bimetallic Y2O3 based catalysts

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Radwa A. El-Salamony ◽  
Sara A. El-Sharaky ◽  
Seham A. Al-Temtamy ◽  
Ahmed M. Al-Sabagh ◽  
Hamada M. Killa
Keyword(s):  
Reaction Mechanism ◽  
Natural Gas ◽  
Fixed Bed ◽  
Catalytic Performance ◽  
Fixed Bed Reactor ◽  
Molar Ratio ◽  
Impregnation Method ◽  
Synthetic Natural Gas ◽  
Methanation Reaction ◽  
Co2 Valorization

Abstract Recently, because of the increasing demand for natural gas and the reduction of greenhouse gases, interests have focused on producing synthetic natural gas (SNG), which is suggested as an important future energy carrier. Hydrogenation of CO2, the so-called methanation reaction, is a suitable technique for the fixation of CO2. Nickel supported on yttrium oxide and promoted with cobalt were prepared by the wet-impregnation method respectively and characterized using SBET, XRD, FTIR, XPS, TPR, and HRTEM/EDX. CO2 hydrogenation over the Ni/Y2O3 catalyst was examined and compared with Co–Ni/Y2O3 catalysts, Co% = 10 and 15 wt/wt. The catalytic test was conducted with the use of a fixed-bed reactor under atmospheric pressure. The catalytic performance temperature was 350 °C with a supply of H2:CO2 molar ratio of 4 and a total flow rate of 200 mL/min. The CH4 yield was reached 67%, and CO2 conversion extended 48.5% with CO traces over 10Co–Ni/Y2O3 catalyst. This encourages the direct methanation reaction mechanism. However, the reaction mechanism over Ni/Y2O3 catalyst shows different behaviors rather than that over bi-metal catalysts, whereas the steam reforming of methane reaction was arisen associated with methane consumption besides increase in H2 and CO formation; at the same temperature reaction.

scholarly journals Performance Analysis of TiO2-Modified Co/MgAl2O4 Catalyst for Dry Reforming of Methane in a Fixed Bed Reactor for Syngas (H2, CO) Production

Energies ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3347
Author(s):  
Arslan Mazhar ◽  
Asif Hussain Khoja ◽  
Abul Kalam Azad ◽  
Faisal Mushtaq ◽  
Salman Raza Naqvi ◽  
...  
Keyword(s):  
Catalytic Activity ◽  
Fixed Bed ◽  
Catalytic Performance ◽  
Dry Reforming ◽  
Fixed Bed Reactor ◽  
Dry Reforming Of Methane ◽  
Catalyst Stability ◽  
Feed Ratio ◽  
Catalyst Loading ◽  
Impregnation Method

Co/TiO2–MgAl2O4 was investigated in a fixed bed reactor for the dry reforming of methane (DRM) process. Co/TiO2–MgAl2O4 was prepared by modified co-precipitation, followed by the hydrothermal method. The active metal Co was loaded via the wetness impregnation method. The prepared catalyst was characterized by XRD, SEM, TGA, and FTIR. The performance of Co/TiO2–MgAl2O4 for the DRM process was investigated in a reactor with a temperature of 750 °C, a feed ratio (CO2/CH4) of 1, a catalyst loading of 0.5 g, and a feed flow rate of 20 mL min−1. The effect of support interaction with metal and the composite were studied for catalytic activity, the composite showing significantly improved results. Moreover, among the tested Co loadings, 5 wt% Co over the TiO2–MgAl2O4 composite shows the best catalytic performance. The 5%Co/TiO2–MgAl2O4 improved the CH4 and CO2 conversion by up to 70% and 80%, respectively, while the selectivity of H2 and CO improved to 43% and 46.5%, respectively. The achieved H2/CO ratio of 0.9 was due to the excess amount of CO produced because of the higher conversion rate of CO2 and the surface carbon reaction with oxygen species. Furthermore, in a time on stream (TOS) test, the catalyst exhibited 75 h of stability with significant catalytic activity. Catalyst potential lies in catalyst stability and performance results, thus encouraging the further investigation and use of the catalyst for the long-run DRM process.

scholarly journals Influence of Ni on Fe and Co-Fe Based Catalysts for High-Calorific Synthetic Natural Gas

Catalysts ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 697
Author(s):  
Tae-Young Kim ◽  
Seongbin Jo ◽  
Yeji Lee ◽  
Suk-Hwan Kang ◽  
Joon-Woo Kim ◽  
...  
Keyword(s):  
Natural Gas ◽  
Catalytic Performance ◽  
Impregnation Method ◽  
Ni Catalysts ◽  
Hydrocarbon Production ◽  
Synthetic Natural Gas ◽  
Fe Catalyst ◽  
Ni Addition ◽  
Hydrocarbon Yield ◽  
Fe Catalysts

Fe-Ni and Co-Fe-Ni catalysts were prepared by the wet impregnation method for the production of high-calorific synthetic natural gas. The influence of Ni addition to Fe and Co-Fe catalyst structure and catalytic performance was investigated. The results show that the increasing of Ni amount in Fe-Ni and Co-Fe-Ni catalysts increased the formation of Ni-Fe alloy. In addition, the addition of nickel to the Fe and Co-Fe catalysts could promote the dispersion of metal and decrease the reduction temperature. Consequently, the Fe-Ni and Co-Fe-Ni catalysts exhibited higher CO conversion compared to Fe and Co-Fe catalysts. A higher Ni amount in the catalysts could increase C1–C4 hydrocarbon production and reduce the byproducts (C5+ and CO2). Among the catalysts, the 5Co-15Fe-5Ni/γ-Al2O3 catalyst affords a high light hydrocarbon yield (51.7% CH4 and 21.8% C2–C4) with a low byproduct yield (14.1% C5+ and 12.1% CO2).

Carbon Dioxide-Expanded Liquid Substrate Phase: An Effective Medium for Selective Hydrogenation of Cinnamaldehyde to Cinnamyl Alcohol.

ChemInform ◽  
2005 ◽  
Vol 36 (12) ◽  
Author(s):  
Fengyu Zhao ◽  
Shin-ichio Fujita ◽  
Jianmin Sun ◽  
Yutaka Ikushima ◽  
Masahiko Arai
Keyword(s):  
Carbon Dioxide ◽  
Selective Hydrogenation ◽  
Effective Medium ◽  
Cinnamyl Alcohol

Effects of Cu and K Promoters on the Catalytic Performance of Iron-Based Nanocatalyst for Fischer-Tropsch Synthesis

2013 ◽  
Vol 832 ◽  
pp. 15-20 ◽  
Author(s):  
Sara Faiz Hanna Tasfy ◽  
Noor Asmawati Mohd Zabidi ◽  
Duvvuri Subbarao
Keyword(s):  
Atmospheric Pressure ◽  
Fixed Bed ◽  
Space Velocity ◽  
Catalytic Performance ◽  
Reactant Ratio ◽  
Impregnation Method ◽  
Fischer Tropsch ◽  
Heavy Hydrocarbons ◽  
Co Conversion ◽  
Iron Based

Iron-based nanocatalyst was prepared via impregnation method on SiO2 support. The effects of promoters, namely, K and Cu, on the physical properties and catalytic performance in FTS have been investigated. The FTS performance of the synthesized nanocatalysts was examined in a fixed-bed microreactor at temperature of 523K, atmospheric pressure, 1.5 reactant ratio (H2/CO) and space velocity of 3L/g-cat.h. In FTS reaction, Cu promoter resulted in a lower CO conversion and C5+ hydrocarbons selectivity but higher selectivity to the lighter hydrocarbons (C1-C4) comparedto those obtained using the K promoter. Higher CO conversion (28.9%) and C5+ hydrocarbons selectivity (54.4%) were obtained using K as a promoter compared to that of Cu promoter. However, the K-promoted nanocatalyst resulted in a lower CO conversion but higher selectivity of the heavy hydrocarbons (C5+) compared to those obtained using the un-promoted nanocatalyst.

scholarly journals Influence of Sulfur-Containing Sodium Salt Poisoned V2O5–WO3/TiO2 Catalysts on SO2–SO3 Conversion and NO Removal

Catalysts ◽  
2018 ◽  
Vol 8 (11) ◽  
pp. 541 ◽  
Author(s):  
Haiping Xiao ◽  
Chaozong Dou ◽  
Hao Shi ◽  
Jinlin Ge ◽  
Li Cai
Keyword(s):  
Photoelectron Spectroscopy ◽  
No Reduction ◽  
Catalytic Performance ◽  
Acid Sites ◽  
Impregnation Method ◽  
So2 Oxidation ◽  
Sodium Salts ◽  
X Ray ◽  
Temperature Programmed ◽  
Physical Features

A series of poisoned catalysts with various forms and contents of sodium salts (Na2SO4 and Na2S2O7) were prepared using the wet impregnation method. The influence of sodium salts poisoned catalysts on SO2 oxidation and NO reduction was investigated. The chemical and physical features of the catalysts were characterized via NH3-temperature programmed desorption (NH3-TPD), H2-temperature programmed reduction (H2-TPR), X-ray photoelectron spectroscopy (XPS), Brunauer–Emmett–Teller (BET), X-ray diffraction (XRD), and Fourier Transform Infrared Spectroscopy (FT-IR). The results showed that sodium salts poisoned catalysts led to a decrease in the denitration efficiency. The 3.6% Na2SO4 poisoned catalyst was the most severely deactivated with denitration efficiency of only 50.97% at 350 °C. The introduction of SO42− and S2O72− created new Brønsted acid sites, which facilitated the adsorption of NH3 and NO reduction. The sodium salts poisoned catalysts significantly increased the conversion of SO2–SO3. 3.6%Na2S2O7 poisoned catalyst had the strongest effect on SO2 oxidation and the catalyst achieved a maximum SO2–SO3-conversion of 1.44% at 410 °C. Characterization results showed sodium salts poisoned catalysts consumed the active ingredient and lowered the V4+/V5+ ratio, which suppressed catalytic performance. However, they increased the content of chemically adsorbed oxygen and the strength of V5+=O bonds, which promoted SO2 oxidation.

scholarly journals Effect of barium loading on CaO derived from waste egg shell heterogeneous catalyst for canola oil biodiesel

2018 ◽  
Vol 192 ◽  
pp. 03006
Author(s):  
Jakkrapong Jitjamnong
Keyword(s):  
Microwave Irradiation ◽  
Heterogeneous Catalyst ◽  
Canola Oil ◽  
Catalytic Performance ◽  
Biodiesel Production ◽  
Catalyst Loading ◽  
Impregnation Method ◽  
Egg Shells ◽  
Infrared Spectrometer ◽  
Egg Shell

The purpose of this research was to investigate the catalytic activity of Ba loading on calcium oxide (CaO) catalyst by varying the amount of barium added during the synthesis: 5-15 wt%. The waste egg shells were utilized as a CaO heterogeneous catalyst by calcined at 900 °C for 2 h. The Ba/CaO catalysts were prepared by impregnation method and were used as a catalyst in transesterification reaction of canola oil via microwave irradiation under microwave power 300 W. The characterization of catalyst and FAME composition of biodiesel were determined by X-ray fluorescence (XRF), scanning electron microscope (SEM), Fourier transform infrared spectrometer (FTIR), and gas chromatography (GC-FID). The conditions of biodiesel production were operated at 60 °C, 3 wt% of catalyst loading, 9:1 methanol-to-canola oil ratio, and microwave irradiation power was 300W for 2 min. The experimental results found that, the waste egg shells consist mainly of CaCO3, which was decomposed to CaO more than 88 wt% after cacination step. The 15 wt% Ba/CaO catalysts exhibited the best catalytic performance with the FAME conversion higher than 97.68%.

Sign in / Sign up

Export Citation Format

Share Document