scholarly journals Nonlinear Robust Backstepping Control for Three-Phase Grid-Connected PV Systems

2018 ◽  
Vol 2018 ◽  
pp. 1-13 ◽  
Author(s):  
Mohamed Habib Boujmil ◽  
Afef Badis ◽  
Mohamed Nejib Mansouri
Keyword(s):  
Control Strategy ◽  
Control Structure ◽  
Control Process ◽  
Backstepping Control ◽  
Operating Conditions ◽  
Cascade Control ◽  
Control Technique ◽  
Pv System ◽  
Pv Systems ◽  
Three Phase

This paper proposes a cascade control structure for three-phase grid-connected Photovoltaic (PV) systems. The PV system consists of a PV Generator, DC/DC converter, a DC link, a DC/AC fully controlled inverter, and the main grid. For the control process, a new control strategy using nonlinear Backstepping technique is developed. This strategy comprises three targets, namely, DC/DC converter control; tight control of the DC link voltage; and delivering the desired output power to the active grid with unity power factor (PF). Moreover, the control process relies mainly on the formulation of stability based on Lyapunov functions. Maximizing the energy reproduced from a solar power generation system is investigated as well by using the Perturb and Observe (P&O) algorithm. The Energetic Macroscopic Representation (EMR) and its reverse Maximum Control Structure (MCS) are used to provide, respectively, an instantaneous average model and a cascade control structure. The robust proposed control strategy adapts well to the cascade control technique. Simulations have been conducted using Matlab/Simulink software in order to illustrate the validity and robustness of the proposed technique under different operating conditions, namely, abrupt changing weather condition, sudden parametric variations, and voltage dips, and when facing measurement uncertainties. The problem of controlling the grid-connected PV system is addressed and dealt by using the nonlinear Backstepping control.

Analysis and Simulation of a High Step-Up DC-DC Converter for Renewable Energy System Applications

2015 ◽  
Vol 775 ◽  
pp. 378-382
Author(s):  
Sudarat Khwan-On ◽  
Sopida Vatcharasukpo
Keyword(s):  
Renewable Energy ◽  
High Voltage ◽  
Control Strategy ◽  
Output Voltage ◽  
Voltage Regulation ◽  
Operating Conditions ◽  
Control Technique ◽  
Power Switch ◽  
Three Phase ◽  
Voltage Conversion

This paper proposes a new step-up DC-DC converter topology with a high voltage conversion ratio for renewable system applications. The desired high voltage gain and satisfactory performance can be achieved by employing only a single power switch with simple control technique. The proposed converter can be used to step up the low voltage generated from renewable energy sources, such as solar photovoltaic modules, to the high level of the dc bus voltage, obtaining low-to-high voltage conversion ratios of approximately 30 times without adopting extremely large duty cycle. Employing the proposed converter the low input voltage (20-50Vdc) can be boosted up to the high output voltage level about 600Vdc at the dc-link bus required for the three-phase inverter feeding the three-phase motor drive system. In this paper, the proposed converter configuration with only one active power switch is presented. The operating principleincluding analysis of the steady-state performance characteristics under continuous conduction mode (CCM) operating conditions is described. In addition, the control strategy is developed in order to obtain the satisfactory output voltage regulation. Finally, simulation results are shown to demonstrate the effectiveness of the proposed converter with its control strategy to achievehigh step-up conversion ratios under different operating conditions.

scholarly journals Cascade Control of Grid-Connected PV Systems Using TLBO-Based Fractional-Order PID

2019 ◽  
Vol 2019 ◽  
pp. 1-17 ◽  
Author(s):  
Afef Badis ◽  
Mohamed Nejib Mansouri ◽  
Mohamed Habib Boujmil
Keyword(s):  
Fractional Order ◽  
Control Strategy ◽  
Optimization Techniques ◽  
Operating Conditions ◽  
Cascade Control ◽  
Dynamic Responses ◽  
Loop Control ◽  
Pv Systems ◽  
Teaching Learning ◽  
Fractional Order Pid

Cascade control is one of the most efficient systems for improving the performance of the conventional single-loop control, especially in the case of disturbances. Usually, controller parameters in the inner and the outer loops are identified in a strict sequence. This paper presents a novel cascade control strategy for grid-connected photovoltaic (PV) systems based on fractional-order PID (FOPID). Here, simultaneous tuning of the inner and the outer loop controllers is proposed. Teaching-learning-based optimization (TLBO) algorithm is employed to optimize the parameters of the FOPID controller. The superiority of the proposed TLBO-based FOPID controller has been demonstrated by comparing the results with recently published optimization techniques such as genetic algorithm (GA), particle swarm optimization (PSO), and ant colony optimization (ACO). Simulations are conducted using MATLAB/Simulink software under different operating conditions for the purpose of verifying the effectiveness of the proposed control strategy. Results show that the performance of the proposed approach provides better dynamic responses and it outperforms the other control techniques.

scholarly journals Different Techniques to Mitigate Partial Shading in Photovoltaic Panels

Energies ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3863
Author(s):  
Tiago Alves ◽  
João Paulo N. Torres ◽  
Ricardo A. Marques Lameirinhas ◽  
Carlos A. F. Fernandes
Keyword(s):  
Cell Model ◽  
Research Work ◽  
Experimental Tests ◽  
Operating Conditions ◽  
Pv System ◽  
Partial Shading ◽  
System Architectures ◽  
Pv Systems ◽  
Advantages And Disadvantages ◽  
Pv Panel

The effect of partial shading in photovoltaic (PV) panels is one of the biggest problems regarding power losses in PV systems. When the irradiance pattern throughout a PV panel is inequal, some cells with the possibility of higher power production will produce less and start to deteriorate. The objective of this research work is to present, test and discuss different techniques to help mitigate partial shading in PV panels, observing and commenting the advantages and disadvantages for different PV technologies under different operating conditions. The motivation is to contribute with research, simulation, and experimental work. Several state-of-the-artsolutions to the problem will be presented: different topologies in the interconnection of the panels; different PV system architectures, and also introducing new solution hypotheses, such as different cell interconnections topologies. Alongside, benefits and limitations will be discussed. To obtain actual results, the simulation work was conducted by creating MATLAB/Simulink models for each different technique tested, all centered around the 1M5P PV cell model. The several techniques tested will also take into account different patterns and sizes of partial shading, different PV panel technologies, different values of source irradiation, and different PV array sizes. The results will be discussed and validated by experimental tests.

scholarly journals New Pulse Width Modulation Technique to Reduce Losses for Three-Phase Photovoltaic Inverters

2018 ◽  
Vol 2018 ◽  
pp. 1-10 ◽  
Author(s):  
Mohannad Jabbar Mnati ◽  
Dimitar V. Bozalakov ◽  
Alex Van den Bossche
Keyword(s):  
Control Strategy ◽  
Pulse Width Modulation ◽  
Photovoltaic System ◽  
Pv System ◽  
Total Cost ◽  
Switching Losses ◽  
Three Phase ◽  
Operational Lifetime ◽  
Term Energy ◽  
Dc Bus

Nowadays, most three-phase, “off the shelf” inverters use electrolytic capacitors at the DC bus to provide short term energy storage. However, this has a direct impact on inverter lifetime and the total cost of the photovoltaic system. This article proposes a novel control strategy called a 120° bus clamped PWM (120BCM). The 120BCM modulates the DC bus and uses a smaller DC bus capacitor value, which is typical for film capacitors. Hence, the inverter lifetime can be increased up to the operational lifetime of the photovoltaic panels. Thus, the total cost of ownership of the PV system will decrease significantly. Furthermore, the proposed 120BCM control strategy modulates only one phase current at a time by using only one leg to perform the modulation. As a result, switching losses are significantly reduced. The full system setup is designed and presented in this paper with some practical results.

scholarly journals Decoupled Control of Three Phase Grid Connected Solar PV System

2019 ◽  
Vol 9 (2) ◽  
pp. 4218-4222
Keyword(s):  
Solar Energy ◽  
Power Factor ◽  
Control Strategy ◽  
Reactive Power ◽  
Standard Test ◽  
Effective Control ◽  
Solar Pv ◽  
Pv System ◽  
Three Phase ◽  
Decoupled Control

A reliable grid connected Photovoltaic (PV) system require effective control schemes for efficient use of solar energy. This paper presents a three-phase grid tied PV system with decoupled real and reactive power control to achieve desired power factor with Maximum Power Point Tracking (MPPT) controller to get maximum solar energy. The synchronous reference frame (dq) control along with decoupling concept is used to control the DC-AC inverter output, while the Phase Locked Loop (PLL) synchronization technique is used to monitor and synchronize the voltage and current at the grid side. The DC-DC converter with Incremental Conductance (InC) based MPPT model is also designed in this paper due to better accuracy compared to Perturb & Observe (P&O) algorithm. The simulation is performed in MATLAB/SIMULINK and a 31.5 kW PV system is modelled to get 30 kW power with the help of MPPT at Standard Test Conditions (STC). Any power factor value between 0.85 lagging to 0.9 leading can be obtained by changingreference q current in this inverter control strategy. The simulation results show that the change of reactive powerdoes not affecttheactive power values of the system, which verifies the effectiveness of the decoupled control strategy of the inverter.

scholarly journals High Performance Multistring Converter Topology for Three-Phase Grid Tied 200 kW Photovoltaic Generating System

2017 ◽  
Vol 1 (2) ◽  
Author(s):  
Mohammad Rustam M. L. ◽  
F. Danang Wijaya
Keyword(s):  
Power Efficiency ◽  
High Performance ◽  
Reactive Power ◽  
Simulation Method ◽  
Operating Conditions ◽  
Total System ◽  
Voltage Reference ◽  
Pv System ◽  
Three Phase ◽  
Converter Topology

Under various external conditions, grid connected PV system performance is strongly affected by the topology that is used to connect a PV system with grid. This research aims to design a multistring based converter topology for three-phase grid connected 200 kW PV system that has a high performance in various operating conditions. Research was done by a simulation method using Matlab-Simulink with performance being evaluated including the generated power, efficiency, power quality in accordance with grid requirements, as well as the power flow. In the simulation, multistring converter topology was designed using two dc-dc boost multistring converters connected in parallel to a centralized of three-phase three-level NPC inverter with the size of the string being shorter and more parallel strings as well as the maximum voltage of the PV array of 273.5 V close to dc voltage reference of 500 V. Each dc-dc boost multistring converter have individual MPPT controllers. The simulation results showed that this multistring converter topology had a high performance in various operating conditions. This due to more power generated by the NPC inverter (> 190 kW) at the time of high power generation on the STC conditions (1000 W/m2, 25 oC), the lowest efficiency of the total system is 95.08 % and the highest efficiency of the total system is 99.4 %, the quality of the power generated in accordance with the requirements of grid, as well as the inverter put more active power to the grid and less reactive power to the grid. The response of the inverter slightly worse for loads with greater reactive power and unbalanced.

scholarly journals A Density Peak-Based Clustering Approach for Fault Diagnosis of Photovoltaic Arrays

2017 ◽  
Vol 2017 ◽  
pp. 1-14 ◽  
Author(s):  
Peijie Lin ◽  
Yaohai Lin ◽  
Zhicong Chen ◽  
Lijun Wu ◽  
Lingchen Chen ◽  
...  
Keyword(s):  
Fault Diagnosis ◽  
Local Density ◽  
Operating Conditions ◽  
Cluster Center ◽  
Pv System ◽  
Density Peak ◽  
Pv Systems ◽  
Distribution Features ◽  
Clustering Approach ◽  
Distance Vector

Fault diagnosis of photovoltaic (PV) arrays plays a significant role in safe and reliable operation of PV systems. In this paper, the distribution of the PV systems’ daily operating data under different operating conditions is analyzed. The results show that the data distribution features significant nonspherical clustering, the cluster center has a relatively large distance from any points with a higher local density, and the cluster number cannot be predetermined. Based on these features, a density peak-based clustering approach is then proposed to automatically cluster the PV data. And then, a set of labeled data with various conditions are employed to compute the minimum distance vector between each cluster and the reference data. According to the distance vector, the clusters can be identified and categorized into various conditions and/or faults. Simulation results demonstrate the feasibility of the proposed method in the diagnosis of certain faults occurring in a PV array. Moreover, a 1.8 kW grid-connected PV system with6×3 PVarray is established and experimentally tested to investigate the performance of the developed method.

Tracking Control Design for Quadrotor Unmanned Aerial Vehicle

2017 ◽  
Vol 67 (3) ◽  
pp. 245 ◽  
Author(s):  
Sudhir Nadda ◽  
A. Swarup
Keyword(s):  
Unmanned Aerial Vehicle ◽  
Control Strategy ◽  
Tracking Control ◽  
Control Method ◽  
Sliding Mode ◽  
Backstepping Control ◽  
Control Technique ◽  
Quadrotor Uav ◽  
Attitude Tracking ◽  
Aerial Vehicle

The model of a quadrotor unmanned aerial vehicle (UAV) is nonlinear and dynamically unstable. A flight controller design is proposed on the basis of Lyapunov stability theory which guarantees that all the states remain and reach on the sliding surfaces. The control strategy uses sliding mode with a backstepping control to perform the position and attitude tracking control. This proposed controller is simple and effectively enhance the performance of quadrotor UAV. In order to demonstrate the robustness of the proposed control method, White Gaussian Noise and aerodynamic moment disturbances are taken into account. The performance of the nonlinear control method is evaluated by comparing the performance with developed linear quadratic regulator and existing backstepping control technique and proportional-integral-derivative from the literature. The comparative performance results demonstrate the superiority and effectiveness of the proposed control strategy for the quadrotor UAV.

Sign in / Sign up

Export Citation Format

Share Document