scholarly journals Application of the Bionic Concept in Reducing the Complexity Noise and Drag of the Mega High-Speed Train Based on Computer Simulation Technologies

Complexity ◽  
2018 ◽  
Vol 2018 ◽  
pp. 1-14
Author(s):  
He-xuan Hu ◽  
Bo Tang ◽  
Ye Zhang
Keyword(s):  
Noise Level ◽  
High Speed ◽  
Aerodynamic Noise ◽  
Leeward Side ◽  
Turbulence Energy ◽  
Aerodynamic Design ◽  
High Speed Train ◽  
High Speed Trains ◽  
Average Noise Level ◽  
Head Type

Regarding the continuous development of high-speed trains and the increase of running speeds, the aerodynamic design of high-speed trains has become significantly important, while reduction of drag and noise comprises a significant challenge in order to optimize aerodynamic design of high-speed trains. The design form factor of a high-speed train is highly influenced by aerodynamic aspects including aerodynamic drag, lift force, and noise. With the high-speed train as the object, the paper aims to take bionic concept as the entry point, selecting the hummingbird as the bionic prototype and extracting bionic elements to establish a bionic train model. Then, the finite volume method was used for numerical simulation and analysis of the aerodynamic performance and aerodynamic noise of the bionic high-speed train. Computational results prove that drag and noise of the bionic head type were lower than those of the original train; drag of the head train of the bionic model was reduced by 2.21% in comparison with the original model, while the whole-train drag was reduced by 3.53%, indicating that drag reduction effects are available and implying that the bionic head type could reduce drag and noise. Noise sources of the bionic train are mainly located at positions with easy airflow separation and violent turbulence motion. Large turbulence energy is in bogie areas and mainly exists at the leeward side of the bogie area. Obviously, the bogie area is the major noise source of the train. Aerodynamic noise of the bionic train in far-field comprises a wide-frequency range. Noises were concentrated within 613 Hz~3150 Hz. When the bionic high-speed train ran at 350 km/h, through comparative analysis of total noise levels at observed points of the high-speed train, it is found that this position with the maximum noise level was 25 m away from the head train nose tip, with the maximum value of 88.4 dB (A). When the bionic train ran at 600 km/h, the maximum sound pressure level at the longitudinal point was 99.7 dB (A) and the average noise level was 96.6 dB (A). When the running speed increased from 350 km/h to 600 km/h, the maximum noise level increased by 11.3 dB (A) and the average noise level increased by 11.6 dB (A). Computation results of aerodynamic noise at the point which is 7.5 m away from the rail center show that the maximum aerodynamic noise level existed at the first-end bogie of the head train, while the noise level was larger at the position closer to the ground.

Research on Model of Noise Prediction of High-Speed Train by SEA Method

2012 ◽  
Author(s):  
Lifang Yang ◽  
Xiaowei He ◽  
Fanyu Meng
Keyword(s):  
High Speed ◽  
Rapid Development ◽  
Noise Analysis ◽  
Input Power ◽  
Aerodynamic Noise ◽  
Noise Prediction ◽  
High Speed Train ◽  
Small Noise ◽  
High Speed Trains ◽  
Calculation Results

China’s rapid development of high-speed train has been in the research spotlight over the years; this paper presents a method to predict the transmission of aerodynamic noise and rail noise inside train compartments for high-speed trains operating at speeds larger than 200 km/h. The numerical tool could be used in parameter studies for noise control. In order to develop the noise prediction model of high speed train, the noise source of high-speed train is analyzed. Based on the noise analysis, the SEA model is built. Due to the small noise difference in one train car, the SEA model is divided into head cab, head passenger cab and middle car three parts. Combined with the finite and boundary element method, the input power and SEA parameters are researched and calculated. In the end of the paper, the results of SEA noise predicting model are compared with theoretical calculation results in order to verify the engineering use.

scholarly journals Aerodynamic Noise Separation of an EMU Trailer Bogie Area Using Train Operation Tests

2018 ◽  
Vol 2018 ◽  
pp. 1-10 ◽  
Author(s):  
Leiming Song ◽  
Hao Chen ◽  
Baochuan Li
Keyword(s):  
Transfer Coefficient ◽  
High Speed ◽  
Noise Analysis ◽  
Central Area ◽  
Aerodynamic Noise ◽  
Frequency Noise ◽  
High Speed Train ◽  
Radiated Noise ◽  
High Speed Trains ◽  
Train Operation

The operation transfer path analysis (OTPA) technique was used to measure the vibration and noise transfer coefficient functions of wheel-rail noise and radiated noise from an electric multiple unit (EMU) train (high-speed train in China) trailer bogie structure to the central area of the trailer bogie for a train running at speeds of 0–5 km/h. By applying these transfer coefficient functions to the noise analysis of high-speed train operation, the contributions of wheel-rail noise and frame-radiated noise to the noise of the bogie area at high speeds are obtained, and the aerodynamic noise is separated from the total noise, providing a reference for vibration damping and noise reduction in high-speed trains. Analysis of test data shows that, in the central area of the trailer bogie of high-speed trains, the low-frequency noise mainly comes from the structural radiated noise of the bogie, and the mid- to high-frequency noise is primarily due to aerodynamic noise. In addition, when an EMU train operates at speeds below 250 km/h, the noise in the central area of the trailer bogie is primarily caused by the structural radiated noise. When the operating speed is higher than 250 km/h, the noise in the central area of the trailer bogie is mainly due to aerodynamic noise, and the aerodynamic noise contribution increases with increase in speed.

Comparative study on the use of acoustic emission and vibration analyses for the bearing fault diagnosis of high-speed trains

2021 ◽  
pp. 147592172110360
Author(s):  
Dongming Hou ◽  
Hongyuan Qi ◽  
Honglin Luo ◽  
Cuiping Wang ◽  
Jiangtian Yang
Keyword(s):  
Acoustic Emission ◽  
Fault Diagnosis ◽  
High Speed ◽  
High Speed Train ◽  
Signal Attenuation ◽  
Transmission Path ◽  
Bearing Fault Diagnosis ◽  
Operation Conditions ◽  
Fault Features ◽  
High Speed Trains

A wheel set bearing is an important supporting component of a high-speed train. Its quality and performance directly determine the overall safety of the train. Therefore, monitoring a wheel set bearing’s conditions for an early fault diagnosis is vital to ensure the safe operation of high-speed trains. However, the collected signals are often contaminated by environmental noise, transmission path, and signal attenuation because of the complexity of high-speed train systems and poor operation conditions, making it difficult to extract the early fault features of the wheel set bearing accurately. Vibration monitoring is most widely used for bearing fault diagnosis, with the acoustic emission (AE) technology emerging as a powerful tool. This article reports a comparison between vibration and AE technology in terms of their applicability for diagnosing naturally degraded wheel set bearings. In addition, a novel fault diagnosis method based on the optimized maximum second-order cyclostationarity blind deconvolution (CYCBD) and chirp Z-transform (CZT) is proposed to diagnose early composite fault defects in a wheel set bearing. The optimization CYCBD is adopted to enhance the fault-induced impact response and eliminate the interference of environmental noise, transmission path, and signal attenuation. CZT is used to improve the frequency resolution and match the fault features accurately under a limited data length condition. Moreover, the efficiency of the proposed method is verified by the simulated bearing signal and the real datasets. The results show that the proposed method is effective in the detection of wheel set bearing faults compared with the minimum entropy deconvolution (MED) and maximum correlated kurtosis deconvolution (MCKD) methods. This research is also the first to compare the effectiveness of applying AE and vibration technologies to diagnose a naturally degraded high-speed train bearing, particularly close to actual line operation conditions.

scholarly journals A Study on the Energy-Harvesting Device with a Magnetic Spring for Improved Durability in High-Speed Trains

Micromachines ◽  
2021 ◽  
Vol 12 (7) ◽  
pp. 830
Author(s):  
Jaehoon Kim
Keyword(s):  
Energy Harvesting ◽  
High Speed ◽  
Permanent Magnets ◽  
Critical Issue ◽  
Sensor Nodes ◽  
High Speed Train ◽  
Vibration Energy Harvesting ◽  
Magnetic Spring ◽  
High Speed Trains ◽  
Energy Harvesting Devices

Durability is a critical issue concerning energy-harvesting devices. Despite the energy-harvesting device’s excellent performance, moving components, such as the metal spring, can be damaged during operation. To solve the durability problem of the metal spring in a vibration-energy-harvesting (VEH) device, this study applied a non-contact magnetic spring to a VEH device using the repulsive force of permanent magnets. A laboratory experiment was conducted to determine the potential energy-harvesting power using the magnetic spring VEH device. In addition, the characteristics of the generated power were studied using the magnetic spring VEH device in a high-speed train traveling at 300 km/h. Through the high-speed train experiment, the power generated by both the metal spring VEH device and magnetic spring VEH device was measured, and the performance characteristics required for a power source for wireless sensor nodes in high-speed trains are discussed.

The Aerodynamic Characteristics of the Pantograph When the Train Passes Through the Tunnel

2017 ◽  
Author(s):  
Dilong Guo ◽  
Wen Liu ◽  
Junhao Song ◽  
Ye Zhang ◽  
Guowei Yang
Keyword(s):  
High Speed ◽  
Aerodynamic Force ◽  
Maximum Amplitude ◽  
Aerodynamic Characteristics ◽  
High Speed Train ◽  
Expansion Waves ◽  
Compression And Expansion ◽  
High Speed Trains ◽  
Current Characteristics ◽  
Pass Through

The aerodynamic force acting on the pantograph by the airflow is obviously unsteady and has a certain vibration frequency and amplitude, while the high-speed train passes through the tunnel. In addition to the unsteady behavior in the open-air operation, the compressive and expansion waves in the tunnel will be generated due to the influence of the blocking ratio. The propagation of the compression and expansion waves in the tunnel will affect the pantograph pressure distribution and cause the pantograph stress state to change significantly, which affects the current characteristics of the pantograph. In this paper, the aerodynamic force of the pantograph is studied with the method of the IDDES combined with overset grid technique when high speed train passes through the tunnel. The results show that the aerodynamic force of the pantograph is subjected to violent oscillations when the pantograph passes through the tunnel, especially at the entrance of the tunnel, the exit of the tunnel and the expansion wave passing through the pantograph. The changes of the pantograph aerodynamic force can reach a maximum amplitude of 106%. When high-speed trains pass through tunnels at different speeds, the aerodynamic coefficients of the pantographs are roughly the same.

scholarly journals Effect of High-Speed Train-Induced Wind on Trackside UAV Thrust Near Railway Bridge

2020 ◽  
Vol 10 (10) ◽  
pp. 3495 ◽  
Author(s):  
Hyuk-Jin Yoon ◽  
Su-Hwan Yun ◽  
Dae-Hyun Kim ◽  
Jae Hee Kim ◽  
Bong-Kwan Cho ◽  
...  
Keyword(s):  
Unmanned Aerial Vehicles ◽  
Wind Velocity ◽  
High Speed ◽  
Railway Bridge ◽  
High Speed Train ◽  
Box Girder ◽  
Railway Bridges ◽  
High Speed Trains ◽  
Thrust Measurement ◽  
Girder Bridge

Imaging devices attached to unmanned aerial vehicles (UAVs) are used for crack measurements of railway bridges constructed for high-speed trains. This research aims to investigate track-side wind induced by high-speed trains and its effect on UAV thrust near the railway bridge. Furthermore, the characteristics of train-induced wind in three axial directions along a track, wind velocity, and the effect of train-induced wind on the UAV thrust were analyzed. This was achieved by installing 3-axis ultrasonic anemometers and a UAV thrust measurement system on top of a PSC box girder bridge. The changes in the train-induced wind velocity were monitored along the train travel, width, and height directions. The train-induced wind was measured at distances of 0.8, 1.3, 2.3, and 2.8 m away from the train’s body to analyze wind velocity based on distance. It was found that the maximum wind velocity decreased linearly as the distance from the train’s body increased. The UAV thrust increased by up to 20% and 60%, owing to train-induced wind when the leading and trailing power cars of a high-speed train passed, respectively. Thus, it is necessary to conduct further research to develop robust control and a variable pitch-propeller that can control thrust.

The Vibration Response Analysis about High-Speed Train’s Braking Wing

2012 ◽  
Vol 226-228 ◽  
pp. 102-105
Author(s):  
Wen Qing Zhu ◽  
Yang Yong Zhu
Keyword(s):  
Finite Element ◽  
High Speed ◽  
Rapid Development ◽  
Response Analysis ◽  
High Speed Train ◽  
High Speed Railway ◽  
Emergency Braking ◽  
Finite Element Software ◽  
High Speed Trains ◽  
Aerodynamic Brake

With the rapid development of high-speed railway in China, the aerodynamic brake is very likely to be an important emergency braking mode of high-speed train in the future. This paper takes aerodynamic braking wing as the object, and uses the finite element software to divide the meshes, then analyses the model influenced by static stress. After simulating the vibratory frequency response of the model in the flow field, it finds that the largest deformation happens in the middle of the upper edge of the wind wing, when the wind speed gets to 500km/h and the load frequency to 4Hz. Some conclusions of this thesis can provide reference for researching the applying the aerodynamic brake in the high-speed trains and laying the foundation for solving the riding and braking safety problems.

Sign in / Sign up

Export Citation Format

Share Document