scholarly journals Compact Ultra-Wide Band MIMO Antenna System for Lower 5G Bands

2018 ◽  
Vol 2018 ◽  
pp. 1-6 ◽  
Author(s):  
Haitham AL-Saif ◽  
Muhammad Usman ◽  
Muhammad Tajammal Chughtai ◽  
Jamal Nasir
Keyword(s):  
Mutual Coupling ◽  
Return Loss ◽  
Wide Band ◽  
Antenna System ◽  
Ultra Wide Band ◽  
Center Frequency ◽  
Mimo Antenna ◽  
Total Structure ◽  
Good Agreement ◽  
Array Geometry

This paper presents a novel compact 2 × 2 planar MIMO antenna system with ultra-wide band capability. Antenna system is specifically designed to target lower 5th generation operating bands ranging from 2 GHz to 12 GHz. This band also covers the IEEE 802.11 a/b/g/n/ac. The antenna array geometry has been simulated using CST MWS. The design is extremely miniaturized with total structure size of 13×25×0.254 mm3. The simulated and measured results have been presented. Measured and simulated return loss values for designed antenna are less than −10 dB over the operating band and lowest values of −35 dB and −32.5 dB can been seen at 5.2 GHz and 9.2 GHz, respectively, whereas at the center frequency the return loss is −25.2 dB. The mutual coupling between both elements is less than −20 dB over the transmission bandwidth. Simulated and measured radiation patterns in E and H planes at center frequency show nearly isotropic far fields. The maximum gain is measured as 4.8 dB. Promising results of Envelope Correlation Coefficient and gain diversity of the design have been achieved. Simulated and measured results are found in good agreement. The fractional bandwidth of antenna is measured as 143.2% which satisfies its ultra-wide band response.

Diversity performance analysis of four port triangular slot MIMO antenna for WiBro and ultrawide band (UWB) applications

Frequenz ◽  
2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Praveen Vummadisetty Naidu ◽  
Sai haranadh Akkapanthula ◽  
Maheshbabu Dhanekula ◽  
Neelima Vummadisetty ◽  
Arvind Kumar
Keyword(s):  
Mutual Coupling ◽  
Group Delay ◽  
Mimo System ◽  
Wide Band ◽  
Cost Effective ◽  
Antenna System ◽  
Ultra Wide Band ◽  
Mimo Antenna ◽  
Capacity Loss ◽  
Uwb Applications

Abstract This article discusses a 4-port micro-strip fed MIMO Antenna system with a triangular slot and an inverted L shape strip has been designed and analysed for both 2.3 GHz WiBro and Ultra-wide-band applications. The suggested antenna has been etched on a cost-effective epoxy (FR-4) substrate having ϵ r ${{\epsilon}}_{r}$  = 4.4 with an overall dimension of 45 × 45 × 1.6 mm3. Mutual coupling of −18 dB between the radiators has been obtained by orthogonal placement of radiators. From the simulated and practical results, the proposed compact MIMO system operates in frequency bands 2.26–2.42 GHz and 3.7–10.8 GHz respectively. The proposed small triangular MIMO system operates with an ECC less than 0.005 with an acceptable channel capacity loss <0.5 bits/s/Hz. Further, the diversity characteristics like DG, MEG, TARC, and group delay have been calculated and are presented in this paper.

Cordate-shaped UWB-MIMO antenna with notch band characteristic and high isolation

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Preeti Pannu ◽  
Devendra Kumar Sharma
Keyword(s):  
Multiple Input Multiple Output ◽  
Small Variation ◽  
Wide Band ◽  
Antenna System ◽  
Data Rate ◽  
Impedance Bandwidth ◽  
Defected Ground Structure ◽  
Content Type ◽  
Mimo Antenna ◽  
Good Agreement

Purpose This paper aims to design a most demanding low profile and compact ultra-wide band (UWB) antenna system for various wireless applications. The performance (in terms of data rate) of UWB system is improved by using multiple-input-multiple-output (MIMO) technology with it. Owing to the overlap of other existing licensed bands with that of UWB, electromagnetic signals can interfere. So, notched band UWB MIMO antenna system reported here which is highly compact, bandwidth efficient, superior data rate and high inter-element isolation comparatively to other reported designs. Design/methodology/approach A 49 × 49 × 1.6 mm3 quad-port UWB MIMO antenna with specific bandwidth elimination property is designed. The proposed planar MIMO configuration comprises unique four identical “Cordate-shaped” monopole radiators fed by 2.3-mm thick microstrip-lines. The radiators are located right-angled to each other to enhance inter-element isolation. Further, a different approach of slitted-substrate is applied to minimize the overall size and mutual coupling of the MIMO antenna, as a substitute of decoupling and matching structures. The defected ground structure is used to obtain −10 dB impedance bandwidth in entire UWB band, without compromising with the lower cut-off frequency response. Further, to eliminate the undesired resonant band (WLAN at 5.5 GHz) from UWB, a rounded split ring resonator is introduced in monopole patch. Findings In the entire operating band of 2.8 to 11 GHz, isolation among elements is more than 24 dB, envelope correlation coefficient less than 0.002, diversity gain greater than 9.99 dB and TARC less than −7 dB are obtained at all 4-ports. Research limitations/implications The measured parameters of the fabricated prototype antenna on FR4 substrate are found in good agreement with the simulated results. The small variation in software results and hardware results are observed due to hardware design limitations. Practical implications The proposed design may be used for any wireless application following in the range of UWB. Originality/value It can be shown from graphs of measured parameters of the fabricated prototype antenna. They found to be in good agreement with the simulated results.

scholarly journals Implications of Metamaterial on Ultra-Wide Band Microstrip Antenna Performance

Crystals ◽  
2020 ◽  
Vol 10 (8) ◽  
pp. 677
Author(s):  
Elham A. Serria ◽  
Mousa I. Hussein
Keyword(s):  
Microstrip Antenna ◽  
Return Loss ◽  
Ring Resonator ◽  
Ground Plane ◽  
Wide Band ◽  
Ring Resonators ◽  
Ultra Wide Band ◽  
Antenna Performance ◽  
Loss Maximum ◽  
Good Agreement

This study is addressing the slotted ring resonator effect on the performance of the ultra-wide band (UWB) microstrip antenna. Two types of metamaterial with double slotted ring resonators (SRR), circular (C-SRR) and square (S-SRR), are studied and implemented on back of the antenna. The design examines the effect of the number of the SRR and its position with respect to the antenna’s ground plane and the rotation of the inner and outer C-SRR rings on different antenna characteristics. The dimensions of the antenna are 45 mm × 31 mm × 1.27 mm. The implementation of the SRR increased the antenna bandwidth to cover the range from 2.2 GHz to 9.8 GHz with rejected bands and frequencies. Antenna simulated characteristics like return loss, maximum gain and radiation pattern are obtained utilizing HFSS. The return loss measurement and the VSWR of the antenna with all SRR configuration studied are in good agreement with simulated results.

Sub-Surface Microwave Imaging Using Four-Slot Vivaldi Antenna with Improved Directivity

Frequenz ◽  
2017 ◽  
Vol 71 (1-2) ◽  
pp. 19-28 ◽  
Author(s):  
Zubair Akhter ◽  
Pankaj Kumar ◽  
M. Jaleel Akhtar
Keyword(s):  
Return Loss ◽  
Wide Band ◽  
Point Of View ◽  
Ultra Wide Band ◽  
Network Analyzer ◽  
Frequency Range ◽  
Radiation Characteristics ◽  
Rf Components ◽  
Vivaldi Antenna ◽  
Good Agreement

Abstract The conventional tapered slot Vivaldi antenna is well known for its ultra-wide band characteristics with low directivity. To improve the directivity of the conventional Vivaldi antenna, a four-slot Vivaldi antenna (FSVA) is proposed here to operate in the frequency range of 2–11 GHz. For feeding the FSVA, a binomial three-section V-shaped even mode power divider with progressing T-junctions is also designed and tested here, which is then integrated with the antenna. The proposed antenna prototype is designed and fabricated on a 1-mm thick FR-4 substrate (ɛr=4.3, tanδ=0.025), and the return loss and radiation characteristics are investigated in the anechoic environment. The measured result shows a good agreement with the numerical simulation performed using the EM Simulator i. e. CST MWS-2015. It is found that the directivity of FSVA is approximately doubled as compared to that of the conventional Vivaldi antenna having the same dimensions. From the application point of view, the fabricated antenna is used to image various metallic objects hidden inside the sand using a vector network analyzer and associated RF components. The obtained 2D microwave images of the test media successfully show that the hidden objects can effectively be located and detected using the proposed FSVA in conjunction with a simple imaging scheme.

scholarly journals Proposal of MIMO Ultra-Wide Band Antenna with Low Mutual Coupling

2015 ◽  
Vol 4 (3-4) ◽  
Author(s):  
Le Trong Trung ◽  
Nguyen Quoc Dinh ◽  
Ta Chi Hieu
Keyword(s):  
Radiation Pattern ◽  
Mutual Coupling ◽  
Wide Band ◽  
Ultra Wide Band ◽  
Broad Bandwidth ◽  
Mimo Antenna ◽  
Maximal Gain ◽  
Antenna Characteristics

In this paper, a new ultra-wide band (UWB) MIMO antenna is proposed. A MIMO antenna set consists of two single ultra-wide band antennas. This simple and compact MIMO antenna, which is designed to work from 3.1 GHz to 10.6 GHz, has a broad bandwidth with the VSWR ≤ 2. In addition, MIMO antenna characteristics such as radiation pattern, maximal gain are thoroughly investigated.

scholarly journals Design of Compact 4 × 4 UWB-MIMO Antenna with WLAN Band Rejection

2014 ◽  
Vol 2014 ◽  
pp. 1-11 ◽  
Author(s):  
Nguyen Khac Kiem ◽  
Huynh Nguyen Bao Phuong ◽  
Dao Ngoc Chien
Keyword(s):  
Dielectric Constant ◽  
Correlation Coefficient ◽  
Frequency Band ◽  
Mutual Coupling ◽  
Return Loss ◽  
Surface Current ◽  
Electromagnetic Bandgap ◽  
Mimo Antenna ◽  
Final Design ◽  
Good Agreement

A compact 4 × 4 UWB-MIMO antenna with rejected WLAN band employing an electromagnetic bandgap (EBG) structure is presented in this paper. The MIMO antenna is electrically small (60 mm × 60 mm), printed on a FR4_epoxy substrate with the dielectric constant of 4.4 and a thickness of 1.6 mm. A mushroom-like EBG structure is used to reject the WLAN frequency at 5.5 GHz. In order to reduce the mutual coupling of the antenna elements, a stub structure acting as a bandstop filter is inserted to suppress the effect of the surface current between elements of the proposed antenna. The final design of the MIMO antenna satisfies the return loss requirement of less than −10 dB in a bandwidth ranging from 2.73 GHz to 10.68 GHz, which entirely covers UWB frequency band, which is allocated from 3.1 to 10.6 GHz. The antenna also exhibits a WLAN band-notched performance at the frequency band of 5.36–6.34 GHz while the values of all isolation coefficients are below −15 dB and the correlation coefficient of MIMO antenna is less than −28 dB over the UWB range. A good agreement between simulation and measurement is shown in this context.

scholarly journals Electromagnetic Soft Surface (EMSS) Integrated MIMO Antennas With Reduced Mutual Coupling And Cross-Polarization Radiation

2021 ◽  
Author(s):  
Swati Bhattacharjee ◽  
Santimoy Mandal ◽  
Chandan Kumar Ghosh
Keyword(s):  
Microstrip Antenna ◽  
Mutual Coupling ◽  
Return Loss ◽  
Satellite Communication ◽  
Antenna System ◽  
Cross Polarization ◽  
Mimo Antenna ◽  
Mimo Antennas ◽  
At Resonance ◽  
Soft Surface

Abstract For closely spaced microstrip antenna elements, Mutual Coupling (MC) is an inevitable phenomenon which degrades antenna performances like gain, radiation pattern, return loss, radiation efficiency etc. Lot of works have been done on the reduction of MC and published the results in the open literatures. This paper presents an approach to suppress MC between two closely spaced microstrip radiators. This is achieved by inserting properly designed EMSS structure between the radiating elements. This EMSS acts as an electrical wall between two rectangular patches and reduces mutual coupling up to 50 dB at resonance frequency of 4.35 GHz. In this attempt, Cross Polarization (XP) reduction of 12.5dB has also been achieved with a gain 5.40dBi for the proposed antenna. The centre to centre spacing between the antenna elements is taken as 22.1mm (0.32λ).The proposed MIMO antenna system can be used for satellite communication and radar system.

Tunable balanced to balanced filtering power divider with high common-mode suppression

Frequenz ◽  
2020 ◽  
Vol 74 (7-8) ◽  
pp. 263-270
Author(s):  
Cao Zeng ◽  
Xue Han Hu ◽  
Feng Wei ◽  
Xiao Wei Shi
Keyword(s):  
Return Loss ◽  
High Selectivity ◽  
Power Divider ◽  
Center Frequency ◽  
Differential Mode ◽  
Common Mode ◽  
Mode Suppression ◽  
The Common ◽  
Equal Power ◽  
Good Agreement

AbstractIn this paper, a tunable balanced-to-balanced in-phase filtering power divider (FPD) is designed, which can realize a two-way equal power division with high selectivity and isolation. A differential-mode (DM) passband with a steep filtering performance is realized by applying microstrip stub-loaded resonators (SLRs). Meanwhile, six varactors are loaded to the SLRs to achieve the center frequency (CF) and bandwidth adjustment, respectively. U-type microstrip lines integrated with stepped impedance slotline resonators are utilized as the differential feedlines, which suppress the common-mode (CM) intrinsically, making the DM responses independent of the CM ones. A tuning center frequency from 3.2 to 3.75 GHz and a fractional bandwidth (12.1–17.6%) with more than 10 dB return loss and less than 2.3 dB insertion loss can be achieved by changing the voltage across the varactors. A good agreement between the simulated and measured results is observed. To the best of authors' knowledge, the proposed balanced-to-balanced tunable FPD is first ever reported.

A printed multiband MIMO antenna with decoupling element

2019 ◽  
Vol 11 (4) ◽  
pp. 413-419 ◽  
Author(s):  
Ziyu Xu ◽  
Qisheng Zhang ◽  
Linyan Guo
Keyword(s):  
Mutual Coupling ◽  
Surface Current ◽  
Antenna System ◽  
Antenna Element ◽  
Coupling Mechanism ◽  
Mimo Antenna ◽  
Resonant Modes ◽  
Monopole Antennas ◽  
Input Multiple Output ◽  
Ground Plate

AbstractA printed multiband Multi-Input Multiple-Output (MIMO) antenna is proposed in this paper. This MIMO antenna system comprises two symmetric printed monopole antennas. Each antenna element consists of multiple bend lines, producing four resonant modes and covering the GSM900, PCS, LTE2300, and 5G bands. Simulated and measured results prove that the proposed MIMO antenna can be applied to traditional 2G, 3G, 4G, and present 5G mobile communication. By etching four inverted L-shaped grooves on its ground plate, mutual coupling between the adjacent antenna elements has been suppressed. This makes the |S21| at all four resonant modes is lower than −40 dB. In addition, its low coupling mechanism has been analyzed by surface current distribution. The designed multiband MIMO antenna provides an idea of reference to realize low mutual coupling between antenna elements, which is also realizable in infrared or optical regimes with appropriate designs.

Sign in / Sign up

Export Citation Format

Share Document