scholarly journals Properties of Ceramic Substrate Materials for High-Temperature Pressure Sensors for Operation above 1000°C

2018 ◽  
Vol 2018 ◽  
pp. 1-6 ◽  
Author(s):  
YanJie Guo ◽  
Fei Lu ◽  
Lei Zhang ◽  
HeLei Dong ◽  
QiuLin Tan ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
High Temperature ◽  
Flexural Strength ◽  
High Performance ◽  
Flexural Modulus ◽  
Pressure Sensors ◽  
Hot Press ◽  
Bend Testing ◽  
Point Bend ◽  
Hot Press Sintering

In order to identify suitable substrate materials for sue in high-temperature pressure sensors that can operate above 1000°C, the high-temperature properties of four high-performance ceramics (99% pure Al2O3 (99Al2O3), 97% pure Al2O3 (97Al2O3), sapphire, and ZrO2) were investigated. Three-point bend testing was used to measure the flexural strengths and flexural moduli of these ceramics, and transient laser emission was used to measure their thermal conductivities. The samples were prepared by hot-press sintering: plates with the dimensions of 3.5 × 5 × 50 mm3 for the bend testing and rods of φ12.5 × 1.5 mm3 for the thermal conductivity measurements. Curves showing the dependence of flexural strength, flexural modulus, and thermal conductivity on temperature were obtained. The results show that the flexural strength and thermal conductivity of sapphire are much greater than those of the other ceramics tested. Thus, we conclude that sapphire is the most appropriate of these materials for use in high-temperature pressure sensors for operation at up to 1000°C.

scholarly journals The Performance of Filava-Polysiloxane, Silres® H62C Composite in High Temperature Application

2021 ◽  
Vol 5 (6) ◽  
pp. 144
Author(s):  
Klaudio Bari ◽  
Thozhuvur Govindaraman Loganathan
Keyword(s):  
High Temperature ◽  
Flexural Strength ◽  
Flexural Modulus ◽  
Fire Retardant ◽  
Bending Test ◽  
Ongoing Research ◽  
Flexural Testing ◽  
Temperature Application ◽  
High Temperature Tensile ◽  
In Fire

The research aim is to investigate the performance of novel enriched mineral fibres (Filava) in polysiloxane SLIRES H62 resin. Specimens were manufactured using a vacuum bagging process and oven cured at 250 °C. Specimens were prepared for flexural testing according to BS EN ISO 14125:1998 to obtain flexural strength, modulus, and elongation. The mechanical strength was compared to similar composites, with the aim of determining composite performance index. The flexural modulus (9.7 GPa), flexural strength (83 MPa), and flexural strain (2.9%) were obtained from a three-point bending test. In addition, the study investigates the thermal properties of the composite using a state-of-art Zwick Roell high temperature tensile rig. The results showed Filava/Polysiloxane Composites had an ultimate tensile strength 400 MPa, Young’s modulus 16 GPa and strain 2.5% at 1000 °C, and no smoke and ash were observed during pyrolysis. Ongoing research is currently taking place to use Filava-H62 in fire-retardant enclosure for lithium-ferro-phosphate Batteries used in electric trucks.

Effect of Iron Additive on the Sintering Behavior of Hot-Pressed ZrC-W Composites

2008 ◽  
Vol 368-372 ◽  
pp. 1764-1766 ◽  
Author(s):  
Yu Jin Wang ◽  
Lei Chen ◽  
Tai Quan Zhang ◽  
Yu Zhou
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Relative Density ◽  
Sintering Temperature ◽  
Sintering Behavior ◽  
Hot Press ◽  
Sintering Additive ◽  
Microstructure And Mechanical Properties ◽  
Hot Press Sintering

The ZrC-W composites with iron as sintering additive were fabricated by hot-press sintering. The densification, microstructure and mechanical properties of the composites were investigated. The incorporation of Fe beneficially promotes the densification of ZrC-W composites. The relative density of the composite sintered at 1900°C can attain 95.3%. W2C phase is also found in the ZrC-W composite sintered at 1700°C. The content of W2C decreases with the increase of sintering temperature. However, W2C phase is not identified in the composite sintered at 1900°C. The flexural strength and fracture toughness of the composites are strongly dependent on sintering temperature. The flexural strength and fracture toughness of ZrC-W composite sintered at optimized temperature of 1800°C are 438 MPa and 3.99 MPa·m1/2, respectively.

Sintering of β-Si3N4 Powder Prepared by Self-Propagating High-Temperature Synthesis (SHS)

2007 ◽  
Vol 546-549 ◽  
pp. 2179-2182 ◽  
Author(s):  
Ling Bai ◽  
Xing Yu Zhao ◽  
Chang Chun Ge
Keyword(s):  
High Temperature ◽  
Silicon Nitride ◽  
Bending Strength ◽  
Sintering Process ◽  
Hot Press ◽  
Temperature Synthesis ◽  
High Temperature Synthesis ◽  
Good Sinter ◽  
The Cost ◽  
Hot Press Sintering

Sintering of the Self-Propagating High-Temperature Synthesis (SHS) of β-Si3N4 powder with 6.67 wt.% Y2O3 and 3.33 wt.% Al2O3 as sintering additives has been emphatically investigated using hot-press sintering process. The relative density of hot-pressed β-Si3N4 reached near to the full densification (99.43%) at 1700°C. The similar micrographs with self-reinforcing rod-like β-Si3N4 grains forming an interlocking structure were observed. The better mechanical properties of hot-pressed Si3N4, such as the hardness (16.73GPa), fracture toughness (5.72 MPa·m1/2) and bending strength (611.72MPa) values, were obtained at 1700°C. The results indicate that good sinter ability can be obtained with the cheaply SHS of silicon nitride powder for preparing silicon nitride materials, which will make the cost of silicon nitride materials lowered.

Synthesis and thermoelectric properties of tantalum-doped ZrNiSn half-Heusler alloys

2014 ◽  
Vol 07 (03) ◽  
pp. 1450032 ◽  
Author(s):  
Degang Zhao ◽  
Min Zuo ◽  
Zhenqing Wang ◽  
Xinying Teng ◽  
Haoran Geng
Keyword(s):  
Thermal Conductivity ◽  
Electrical Conductivity ◽  
Acoustic Phonon ◽  
Figure Of Merit ◽  
Room Temperature ◽  
Phonon Scattering ◽  
Heusler Alloys ◽  
Hot Press ◽  
Arc Melting ◽  
Hot Press Sintering

The Ta -doped ZrNiSn half-Heusler alloys, Zr 1-x Ta x NiSn , were synthesized by arc melting and hot-press sintering. Microstructure of Zr 1-x Ta x NiSn compounds were analyzed and the thermoelectric (TE) properties of Zr 1-x Ta x NiSn compounds were measured from room temperature to 823 K. The electrical conductivity increased with increasing Ta content. The Seebeck coefficient of Zr 1-x Ta x NiSn compounds was sharply decreased with increasing Ta content. The Hall mobility was proportional to T-1.5 above 673 K, indicating that the acoustic phonon scattering was predominant in the temperature range. The thermal conductivity was effectively depressed by introducing Ta substitution. The figure of merit of ZrNiSn compounds was improved due to the decreased thermal conductivity and increased electrical conductivity. The maximum ZT value of 0.60 was achieved for Zr 0.97 Ta 0.03 NiSn sample at 823 K.

scholarly journals Hierarchical network enabled flexible textile pressure sensors with ultra-high sensitivity, ultra-wide linearity and high-temperature resistance

2021 ◽  
Author(s):  
Meiling Jia ◽  
Chenghan Yi ◽  
Yankun Han ◽  
Xin Li ◽  
Guoliang Xu ◽  
...  
Keyword(s):  
High Pressure ◽  
High Temperature ◽  
Pressure Sensor ◽  
High Performance ◽  
Full Range ◽  
Pressure Sensors ◽  
Fiber Surface ◽  
High Sensitivity ◽  
Harsh Environments ◽  
Point To Point

Abstract Thin, lightweight, and flexible textile pressure sensors with the ability to precisely detect the full range of faint pressure (< 100 Pa), low pressure (in the range of KPa) and high pressure (in the range of MPa) are in significant demand to meet the requirements for applications in daily activities and more meaningfully in some harsh environments, such as high temperature and high pressure. However, it is still a major challenge to fulfill these requirements simultaneously in a single pressure sensor. Herein, a high-performance pressure sensor enabled by polyimide fiber fabric with functionalized carbon-nanotube (PI/FCNT) is obtained via a facile electrophoretic deposition (EPD) approach. High-density FCNT is evenly wrapped and chemically bonded to the fiber surface during the EPD process, forming a conductive hierarchical fiber/FCNT matrix. Benefiting from the abundant yet firm contacting points, point-to-point contacting mode, and high elastic modulus of both PI and CNT, the proposed PI/FCNT pressure sensor exhibits ultra-high sensitivity (3.57 MPa− 1), ultra-wide linearity (3.24 MPa), exceptionally broad sensing range (~ 45 MPa), and long-term stability (> 4000 cycles). Furthermore, under a high working temperature of 200 ºC, the proposed sensor device still shows an ultra-high sensitivity of 2.64 MPa− 1 within a wide linear range of 7.2 MPa, attributing to its intrinsic high-temperature-resistant properties of PI and CNT. Thanks to these merits, the proposed PI/FCNT(EPD) pressure sensor could serve as an E-skin device to monitor the human physiological information, precisely detect tiny and extremely high pressure, and can be integrated into an intelligent mechanical hand to detect the contact force under high-temperature (> 300 ºC), endowing it with high applicability in the fields of real-time health monitoring, intelligent robots, and harsh environments.

scholarly journals Investigation of the thermal conductivity and flexural strength of polymethylmethacrylate denture base material with SiC and Al2O3 added

2019 ◽  
Author(s):  
esra kul ◽  
faruk yeşildal
Keyword(s):  
Thermal Conductivity ◽  
Elastic Modulus ◽  
Thermal Diffusivity ◽  
Flexural Strength ◽  
Base Material ◽  
Young Modulus ◽  
Environmental Scanning ◽  
Denture Base ◽  
Significant Difference ◽  
Point Bend

Abstract Background:Although polymethylmethacrylate (PMMA) is widely used as a denture base material, its disadvantages include low strength and low thermal conductivity. The effects on thermal conductivity, flexural strength, thermal diffusivity,and elastic modulus of adding Al2O3and SiC powders in different volumes to PMMA were investigated. Methods:A total of 60 specimens were prepared in 10 groups (five groups for the thermal conductivity test and five groups for the flexural strength test) (Table 3). The specimens were immersed in water for 30 days before the testing. Thermal conductivity values were measured by the transient hot bridge (THB) method, and flexural strengths were measured by the 3-point bend test. A significant difference was found in thermal conductivity, flexural strength, thermal diffusivity and elastic modulus values between independent groups (P <0.001) using the Kruskal-Wallis test. The Kruskal Wallis 1-way ANOVA was used for the post hoc tests after Kruskal Wallis (α=.05). Results: The thermal conductivity of PMMA increased significantly with the addition of 15% SiC and 15% Al2O3. The flexural strength values ​​decreased significantly with the addition of 10% SiC and 15% Al2O3. The thermal diffusivity values increased significantly with the addition of 10% and 15% SiC. The Young modulus of PMMA decreased when 10% SiC, 10% Al2O3and 15% Al2O3 were added. Environmental scanning electron microscope (ESEM) showed that ceramic powders were dissipated in PMMA. Conclusions: The addition of 15% SiC powders to PMMA increased thermal conductivity without significantly reducing flexural strength.

The high temperature three point bend testing of proton irradiated 316L stainless steel and Mod 9Cr–1Mo

2005 ◽  
Vol 343 (1-3) ◽  
pp. 191-196 ◽  
Author(s):  
Stuart A. Maloy ◽  
A. Zubelewicz ◽  
T. Romero ◽  
M.R. James ◽  
W.F. Sommer ◽  
...  
Keyword(s):  
Stainless Steel ◽  
High Temperature ◽  
316L Stainless Steel ◽  
Bend Testing ◽  
Point Bend

Property and Microstructure of CNTs/AlN Ceramics

2010 ◽  
Vol 434-435 ◽  
pp. 48-49 ◽  
Author(s):  
Hong Lei Wang ◽  
Xin Gui Zhou ◽  
Hai Jiao Yu ◽  
Shuang Zhao ◽  
Zheng Luo
Keyword(s):  
Thermal Conductivity ◽  
High Temperature ◽  
Fracture Surface ◽  
Flexural Strength ◽  
Grain Boundary ◽  
Bulk Density ◽  
Hot Pressing ◽  
Microstructure Observation ◽  
High Temperature And Pressure ◽  
Temperature And Pressure

CNTs/AlN ceramics were fabricated by hot-pressing and their bulk density, flexural strength, thermal conductivity were characterized. The microstructure was also investigated. The fracture surface were analyzed by SEM. TEM was used for analyzing the microstructure. It is found that the density, mechanic and thermal-conductivity properties markedly decreased as the CNTs reinforced AlN ceramic; through microstructure observation, the conglomeration of CNTs mostly exist among the AlN grain boundary, and the CNTs were scathed by the high temperature and pressure of the hot-pressing.

scholarly journals Effects of Combined Usage of Supplementary Cementitious Materials on the Thermal Properties and Microstructure of High-Performance Concrete at High Temperatures

Materials ◽  
2020 ◽  
Vol 13 (8) ◽  
pp. 1833 ◽  
Author(s):  
Dong Lu ◽  
Zhuo Tang ◽  
Liang Zhang ◽  
Jianwei Zhou ◽  
Yue Gong ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
High Temperature ◽  
Fly Ash ◽  
High Temperatures ◽  
High Performance ◽  
High Performance Concrete ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Amorphous Phases ◽  
Micro Cracks

Concrete has low porosity and compact microstructure, and thus can be vulnerable to high temperature, and the increasing application of various types of supplementary cementitious materials (SCMs) in concrete makes its high-temperature resistant behavior more complex. In this study, we investigate the effects of four formulations with typical SCMs combinations of fly ash (FA), ultra-fine fly ash (UFFA) and metakaolin (MK), and study the effects of SCMs combinations on the thermal performance, microstructure, and the crystalline and amorphous phases evolution of concrete subjected to high temperatures. The experimental results showed that at 400 °C, with the addition of 20% FA (wt %), the thermal conductivity of the sample slightly increased to 1.5 W/(m·K). Replacing FA with UFFA can further increase the thermal conductivity to 1.7 W/(m·K). Thermal conductivity of concrete slightly increased at 400 °C and significantly reduced at 800 °C. Further, combined usage of SCMs delayed and reduced micro-cracks of concrete subjected to high temperatures. This study demonstrates the potential of combining the usage of SCMs to promote the high-temperature performance of concrete and explains the micro-mechanism of concrete containing SCMs at high temperatures.

Characterization of exfoliated graphite nanoplatelets/polycarbonate composites: electrical and thermal conductivity, and tensile, flexural, and rheological properties

2011 ◽  
Vol 46 (9) ◽  
pp. 1029-1039 ◽  
Author(s):  
Julia A King ◽  
Michael D Via ◽  
Faith A Morrison ◽  
Kyle R Wiese ◽  
Edsel A Beach ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Tensile Strength ◽  
Electrical Resistivity ◽  
Ultimate Tensile Strength ◽  
Flexural Strength ◽  
Rheological Properties ◽  
Flexural Modulus ◽  
Exfoliated Graphite ◽  
Graphite Nanoplatelets ◽  
Exfoliated Graphite Nanoplatelets

Exfoliated graphite nanoplatelets (GNP) can be added polymers to produce electrically conductive composites. In this study, varying amounts (2–15 wt%) GNP were added to polycarbonate (PC) and the resulting composites were tested for electrical conductivity (1/electrical resistivity), thermal conductivity, and tensile, flexural, and rheological properties. The percolation threshold was approximately 4.0 vol% (6.5 wt%) GNP. The addition of GNP to polycarbonate increased the composite electrical and thermal conductivity and tensile and flexural modulus. The 8 wt% (5.0 vol%) GNP in polycarbonate composite had a good combination of properties for electrostatic dissipative applications. The electrical resistivity and thermal conductivity were 4.0 × 107 ohm-cm and 0.37 W/m · K, respectively. The tensile modulus, ultimate tensile strength, and strain at ultimate tensile strength were 3.5 GPa, 58 MPa, and 3.5%, respectively. The flexural modulus, ultimate flexural strength, and strain at ultimate flexural strength were 3.6 GPa, 108 MPa, and 5.5%, respectively. Ductile tensile behavior is noted in pure polycarbonate and in samples containing up to 8 wt% GNP. PC and GNP/PC composites show shear-thinning behavior. Viscosity of the composite increased as the amount of GNP increased dueto a volume-filling filler effect. The viscosity of the GNP/PC composites are well described by a Kitano-modified Maron-Pierce model.

Sign in / Sign up

Export Citation Format

Share Document