scholarly journals Experimental Study on Drop-Weight Impact Response of Basalt Fiber Aluminum Laminates (BFMLs)

2018 ◽  
Vol 2018 ◽  
pp. 1-13
Author(s):  
Dongliang Zhang ◽  
Xiaoyan Zhang ◽  
Yunrong Luo ◽  
Qingyuan Wang
Keyword(s):  
Energy Absorption ◽  
Volume Fraction ◽  
Basalt Fiber ◽  
Fiber Reinforced Polymer ◽  
Aluminum Sheet ◽  
Fiber Reinforced ◽  
Reinforced Polymer ◽  
Drop Weight ◽  
Weight Impact ◽  
Basalt Fiber Reinforced Polymer

The basalt fiber-reinforced polymer (epoxy resin), which has even better mechanical properties than glass fiber-reinforced polymer, is a good choice for making FML (fiber-metal laminate) composite. Herein, drop-weight impact tests of basalt fiber-based FMLs (called BFMLs) were conducted in the INSTON 9520HV testing machine to investigate the low-velocity impact properties of BFMLs. The specimens were of two diameters. And the impactors had two sizes of nose, dropping from different heights. The load-deflection behavior of aluminum sheet, BFRP (basalt fiber-reinforced polymer) panel, and BFML plate and their energy dissipation patterns during impact perforation were obtained. The test results showed that aluminum alloy sheet and BFMLs had no strain rate effect, while BFRP did. It was also concluded that the behavior of the thick BFML plate was clearly affected by debonding between aluminum sheet and BFRP panel, while the behavior of the thin BFML plate was controlled by membrane force. In failure analysis, it was found that the deformation and breakage of BFRP are the main contributions to energy absorption of BFMLs which counts for more than 75%. The energy absorbed by the aluminum sheet through plastic deformation and petaling is about 20%, while the energy absorbed in debonding can be ignored. In addition, with the help of ABAQUS simulation, it was found that decreasing the value of MVF (metal volume fraction) can increase the specific energy absorption of BFMLs, but the ductility of BFMLs may decrease.

Compressive Behavior of Circular Concrete Columns Confined by Basalt Fiber Reinforced Polymer (BFRP)

2018 ◽  
Vol 765 ◽  
pp. 355-360 ◽  
Author(s):  
Sakol Suon ◽  
Shahzad Saleem ◽  
Amorn Pimanmas
Keyword(s):  
Basalt Fiber ◽  
Concrete Columns ◽  
Primary Objective ◽  
Fiber Reinforced Polymer ◽  
Small Scale ◽  
Fiber Reinforced ◽  
Compressive Behavior ◽  
Reinforced Polymer ◽  
Ductile Behavior ◽  
Basalt Fiber Reinforced Polymer

This paper presents an experimental study on the compressive behavior of circular concrete columns confined by a new class of composite materials originated from basalt rock, Basalt Fiber Reinforced Polymer (BFRP). The primary objective of this study is to observe the compressive behavior of BFRP-confined cylindrical concrete column specimens under the effect of different number of layers of basalt fiber as a study parameter (3, 6, and 9 layers). For this purpose, 8 small scale circular concrete specimens with no internal steel reinforcement were tested under monotonic axial compression to failure. The results of BFRP-confined concrete specimens of this study showed a bilinear stress-strain response with two ascending branches. Consequently, the performance of confined columns was improved as the number of BFRP layer was increased, in which all the specimens exhibited ductile behavior before failure with significant strength enhancement. The experimental results indicate the well-performing of basalt fiber in improving the concrete compression behavior with an increase in number of FRP layers.

Relaxation behavior of prestressing basalt fiber-reinforced polymer tendons considering anchorage slippage

2016 ◽  
Vol 51 (9) ◽  
pp. 1275-1284 ◽  
Author(s):  
Jianzhe Shi ◽  
Xin Wang ◽  
Huang Huang ◽  
Zhishen Wu
Keyword(s):  
Relaxation Rate ◽  
Basalt Fiber ◽  
Relaxation Behavior ◽  
Fiber Reinforced Polymer ◽  
Initial Stresses ◽  
Fiber Reinforced ◽  
Relaxation Rates ◽  
Reinforced Polymer ◽  
Relaxation Loss ◽  
Basalt Fiber Reinforced Polymer

Relaxation is a key factor that controls the application of prestressing fiber-reinforced polymer tendons. This paper focuses on the evaluation of the relaxation behavior of newly developed basalt fiber-reinforced polymer tendons through an approach considering anchorage slippage. A series of relaxation tests on basalt fiber-reinforced polymer tendons subjected to three levels of initial stresses (0.4 fu, 0.5 fu, and 0.6 fu, where fu = ultimate strength) were conducted using a specially designed test setup that eliminates the impact of slippage at the anchor zone. An additional group of tests was conducted to validate the enhancement effect of pretension on the relaxation behavior. The relaxation rates at one million hours were predicted based on experimental fitting. Finally, the relaxation rates at 1000 h were predicted using the correlation between the relaxation and creep and were validated with the experimental relaxation rates. The results demonstrate the effectiveness of the proposed setup in measuring the relaxation loss of specimens and reveal that the relaxation rates of untreated basalt fiber-reinforced polymer tendons at 1000 h are 4.2%, 5.3%, and 6.4% at 0.4 fu, 0.5 fu, and 0.6 fu, respectively. Pretension treatment performs effective in relaxation loss controlling. BFRP tendons are recommended to be applied at an initial stress of 0.5 fu after pretension treatment, with one-million-hour relaxation rate equal to 6.7%. Furthermore, the relaxation rate at 1000 h can be predicted accurately based on the creep behavior. The conclusions of this study can provide guidance for the prestressing applications of basalt fiber-reinforced polymer tendons.

scholarly journals Impact Properties of Nanomodified Basalt Fiber Reinforced Polymer Composites

2019 ◽  
Vol 9 (1) ◽  
pp. 5839-5844
Keyword(s):  
Polymer Composite ◽  
Impact Load ◽  
Basalt Fiber ◽  
Optical Microscope ◽  
Fiber Reinforced Polymer ◽  
Low Velocity Impact ◽  
Fiber Reinforced ◽  
Basalt Fibre ◽  
Reinforced Polymer ◽  
Basalt Fiber Reinforced Polymer

Basalt fibre reinforced polymer composite is a newly versatile material that has good potential to be used in many applications due to its high specific modulus and strength properties. This paper is aimed to evaluate the response and properties of BFRP composite when it is subjected to low-velocity impact loading. The BFRP laminates were fabricated using vacuum bagging method. The effects of 5, 10 and 15wt% nanosilica particles on density, impact load and energy absorbed were investigated using a drop weight impact test. The damage characteristics of the samples were examined using an optical microscope. The addition of 15wt% nanosilica into Basalt fiber reinforced polymer composite significantly improved the energy absorption properties of the specimens. This suggests that the nanomodified BFRP composite has better damage resistance properties when compared to the pure system.

Basalt Fiber-Reinforced Polymer Composites

2021 ◽  
pp. 31-69
Author(s):  
R.A. Ilyas ◽  
T.M.N. Afiq ◽  
R.M. Affiq ◽  
T.H. Tahrim ◽  
S.M. Sapuan ◽  
...  
Keyword(s):  
Polymer Composites ◽  
Basalt Fiber ◽  
Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Reinforced Polymer ◽  
Fiber Reinforced Polymer Composites ◽  
Basalt Fiber Reinforced Polymer
Sign in / Sign up

Export Citation Format

Share Document