scholarly journals Acoustic Emission Monitoring and Failure Precursors of Sandstone Samples under Various Loading and Unloading Paths

2017 ◽  
Vol 2017 ◽  
pp. 1-11 ◽  
Author(s):  
Jie Xu ◽  
Jingdong Jiang ◽  
Lingling Zuo ◽  
Yufeng Gao
Keyword(s):  
Acoustic Emission ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Sandstone Sample ◽  
Mode Decomposition ◽  
Conventional Triaxial Compression ◽  
Confining Pressures ◽  
Loading And Unloading ◽  
Precursor Information ◽  
Failure Precursors

To explore the failure precursors of hard rock, a series of triaxial loading and unloading experiments were carried out on sandstone sample using the acoustic emission systems. The extreme-point symmetric mode decomposition method (ESMD method) was used to denoise and reconstruct the AE data. The AE quiet period in Scheme I becomes much more obvious with the confining pressure increasing, which can be regarded as the precursor information of the sample failure under conventional triaxial compression. Unlike Scheme I, there are no obvious precursory characteristics before failure in Schemes II and III, and the count rate reaches the maximum at the peak point. When the stress ratio ranges from 0.8 to 1.0, the fractal values of acoustic emission can be used to investigate the failure precursors of samples at a lower confining pressure. When the time ratio is greater than 0.8 under higher confining pressures, the fractal values of sandstone samples under unloading paths are rapidly reduced, which can be used to predict rock failure at higher confining pressures.

scholarly journals Elastic-Plastic Threshold and Rational Unloading Level of Rocks

2019 ◽  
Vol 9 (15) ◽  
pp. 3164 ◽  
Author(s):  
Ming Ji ◽  
Hongjun Guo
Keyword(s):  
Stress Level ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Confining Stress ◽  
Elastic Plastic ◽  
Conventional Triaxial Compression ◽  
Confining Pressures ◽  
Pressure Increment ◽  
Loading And Unloading ◽  
Plastic Transformation

During loading and unloading test, various rocks manifest different stress values of elastic-plastic transformation. This study proposes to include axial pressure increment ratio in the conventional triaxial compression test to evaluate different variables (nominal elastic modulus, nominal Poisson’s ratio, strain, and energy). The relationships among various factors including variables, the stress level of initial confining stress and axial pressures, were analyzed by analyzing the stress–strain plot record obtained from testing various rocks. The extreme value point of the deformation parameter, also known as the elastic-plastic threshold, was analyzed. In addition, the elastic-plastic thresholds were later used as unloading points during the unloading tests. Under the same confining condition, different rocks demonstrated different unloading levels. Furthermore, a linear correlation was observed between unloading levels and changing confining pressures, and the gradient is mainly related to the types of rocks. During the unloading tests of rocks, the rational unloading level is recommended to be no higher than the stress level at the elastic-plastic threshold under the corresponding confining pressure.

Post-Critical Mechanical Properties Of Sedimentary Rocks In The Upper Silesian Coal Basin (Poland)

2015 ◽  
Vol 60 (2) ◽  
pp. 517-534 ◽  
Author(s):  
Mirosława Bukowska
Keyword(s):  
Triaxial Compression ◽  
Residual Deformation ◽  
Confining Pressure ◽  
Compression Tests ◽  
Functional Relationships ◽  
Conventional Triaxial Compression ◽  
Upper Silesian Coal Basin ◽  
Confining Pressures ◽  
Waste Rocks ◽  
Triaxial Compression Tests

AbstractIn this paper, we present the results of a study of the Upper Carboniferous sedimentary rocks of the Upper Silesian Coal Basin (USCB) in Poland. We examined the hard coals, which belong to various stratigraphic units of Upper Carboniferous coal-bearing strata, and waste rocks, i.e., sandstones, mudstones, claystones. We present the results of tests of their post-critical mechanical properties. These results are from tests of the post-critical modulus, residual stress and residual deformation from experiments using a servo-controlled testing machine (MTS) with uniaxial compression and conventional triaxial compression. We applied confining pressures of up to 50 MPa at a strain rate of 10−5− 10−1s−1(0.003-6.0 mm/sec). The confining pressure applied in the triaxial compression tests reflected the conditions of current and future mining activities in the USCB at depths exceeding 1.300 metres. The strain rate applied in the tests reflected the values observed in the rockmass surrounding the mine workings and the rate of certain geodynamic phenomena occurring in the Carboniferous rockmass in the USCB, e.g., rock bursts. We present the values of the sub-critical modulus of coals and waste rocks, the functional relationships between the post-critical modulus and uniaxial compression strength, which are described using an exponential function of high correlation coefficients of the given rocks, and an exponential relationship between the post-critical modulus and the longitudinal elasticity modulus (Young’s modulus). Based on the results of tests of the post-critical properties of the Carboniferous rocks under triaxial compression and at various strain rates, we devised the functional relationships between the properties of the rocks and the confining pressure. The dependence of the post-critical modulus of the sandstones and claystones on the confining pressure is described using a polynomial function of degree 2, and that of the coals is described using an exponential function. The relationship between the residual stress and residual deformation in the rocks and the confining pressure was described using a linear function. The obtained results of tests have a practical application in forecasting behaviour of rocks located deep, and designing safe exploitation of mineral deposits. Confining pressures of up to 50 MPa used in the conventional triaxial compression tests allowed us to predict the behaviour of the rock mass at large depths. These data provide general knowledge of the tendencies in behaviour of rocks at substantial depths and the ability to design safe methods of mining deposits of various raw materials, including energy sources. These deposits are mined from increasingly great depths as the reserves are gradually exhausted and collieries of the largest European coal basins are continuously reconfigured.

Study on mechanical properties and damage evolution of carbonaceous shale under triaxial compression with acoustic emission

2021 ◽  
pp. 105678952199119
Author(s):  
Kai Yang ◽  
Qixiang Yan ◽  
Chuan Zhang ◽  
Wang Wu ◽  
Fei Wan
Keyword(s):  
Mechanical Properties ◽  
Acoustic Emission ◽  
Water Content ◽  
Damage Evolution ◽  
Damage Assessment ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Damage Variable ◽  
Natural State ◽  
Carbonaceous Shale

To explore the mechanical properties and damage evolution characteristics of carbonaceous shale with different confining pressures and water-bearing conditions, triaxial compression tests accompanied by simultaneous acoustic emission (AE) monitoring were conducted on carbonaceous shale rock specimens. The AE characteristics of carbonaceous shale were investigated, a damage assessment method based on Shannon entropy of AE was further proposed. The results suggest that the mechanical properties of carbonaceous shale intensify with increasing confining pressure and degrade with increasing water content. Moisture in rocks does not only weaken the cohesion but also reduce the internal friction angle of carbonaceous shale. It is observed that AE activities mainly occur in the post-peak stage and the strong AE activities of saturated carbonaceous shale specimens appear at a lower normalized stress level than that of natural-state specimens. The maximum AE counts and AE energy increase with water content while decrease with confining pressure. Both confining pressure and water content induce changes in the proportions of AE dominant frequency bands, but the changes caused by confining pressure are more significant than those caused by water content. The results also indicate that AE entropy can serve as an applicable index for rock damage assessment. The damage evolution process of carbonaceous shale can be divided into two main stages, including the stable damage development stage and the damage acceleration stage. The damage variable increases slowly accompanied by a few AE activities at the first stage, which is followed by a rapid growth along with intense acoustic emission activities at the damage acceleration stage. Moreover, there is a sharp rise in the damage evolution curve for the natural-state specimen at the damage acceleration stage, while the damage variable develops slowly for the saturated-state specimen.

Mechanical behaviour of powders using a medium pressure flexible boundary cubical triaxial tester

2003 ◽  
Vol 217 (3) ◽  
pp. 233-241 ◽  
Author(s):  
F Li ◽  
V M Puri
Keyword(s):  
Shear Modulus ◽  
Mechanical Behaviour ◽  
Triaxial Compression ◽  
Three Dimensional ◽  
Volumetric Strain ◽  
Confining Pressure ◽  
Alumina Powder ◽  
Medium Pressure ◽  
Mean Pressure ◽  
Confining Pressures

A medium pressure (<21 MPa) flexible boundary cubical triaxial tester was designed to measure the true three-dimensional response of powders. In this study, compression behaviour and strength of a microcrystalline cellulose powder (Avicel® PH102), a spray-dried alumina powder (A16SG), and a fluid-bed-granulated silicon nitride based powder (KY3500) were measured. To characterize the mechanical behaviour, three types of triaxial stress paths, that is, the hydrostatic triaxial compression (HTC), the conventional triaxial compression (CTC), and the constant mean pressure triaxial compression (CMPTC) tests were performed. The HTC test measured the volumetric response of the test powders under isostatic pressure from 0 to 13.79MPa, during which the three powders underwent a maximum volumetric strain of 40.8 per cent for Avicel® PH102, 30.5 per cent for A16SG, and 33.0 per cent for KY3500. The bulk modulus values increased 6.4-fold from 57 to 367MPa for Avicel® PH102, 3.7-fold from 174 to 637 MPa for A16SG, and 8.1-fold from 74 to 597MPa for KY3500, when the isotropic stress increased from 0.69 to 13.79 MPa. The CTC and CMPTC tests measured the shear response of the three powders. From 0.035 to 3.45MPa confining pressure, the shear modulus increased 28.7-fold from 1.6 to 45.9MPa for Avicel® PH102, 35-fold from 1.7 to 60.5MPa for A16SG, and 28.5-fold from 1.5 to 42.8MPa for KY3500. In addition, the failure stresses of the three powders increased from 0.129 to 4.41 MPa for Avicel® PH102, 0.082 to 3.62 MPa for A16SG, and 0.090 to 4.66MPa for KY3500, respectively, when consolidation pressure increased from 0.035 to 3.45MPa. In addition, the shear modulus and failure stress values determined from the CTC test at 2.07, 2.76, and 3.45MPa confining pressures are consistently greater than those from the CMPTC test at the same constant mean pressures. This observation demonstrates the influence of stress paths on material properties. The CTT is a useful tool for characterizing the three-dimensional response of powders and powder mixtures.

Experimental investigation of the effect of compliant pores on reservoir rocks under hydrostatic and triaxial compression stress states

2019 ◽  
Vol 56 (7) ◽  
pp. 983-991
Author(s):  
Hua Yu ◽  
Kam Ng ◽  
Dario Grana ◽  
John Kaszuba ◽  
Vladimir Alvarado ◽  
...  
Keyword(s):  
Pore Pressure ◽  
Triaxial Compression ◽  
Matrix Material ◽  
Volumetric Strain ◽  
Confining Pressure ◽  
Differential Pressure ◽  
Sandstone Sample ◽  
Stress States ◽  
Rock Springs ◽  
Stage 1

The presence of compliant pores in rocks is important for understanding the stress–strain behaviors under different stress conditions. This paper describes findings on the effect of compliant pores on the mechanical behavior of a reservoir sandstone under hydrostatic and triaxial compression. Laboratory experiments were conducted at reservoir temperature on Weber Sandstone samples from the Rock Springs Uplift, Wyoming. Each experiment was conducted at three sequential stages: (stage 1) increase in the confining pressure while maintaining the pore pressure, (stage 2) increase in the pore pressure while maintaining the confining pressure, and (stage 3) application of the deviatoric load to failure. The nonlinear pore pressure – volumetric strain relationship governed by compliant pores under low confining pressure changes to a linear behavior governed by stiff pores under higher confining pressure. The estimated compressibilities of the matrix material in sandstone samples are close to the typical compressibility of quartz. Because of the change in pore structures during stage 1 and stage 2 loadings, the estimated bulk compressibilities of the sandstone sample under the lowest confining pressure decrease with increasing differential pressure. The increase in crack initiation stress is limited with increasing differential pressure because of similar total crack length governed by initial compliant porosity in sandstone samples.

scholarly journals Researches on the Constitutive Models of Artificial Frozen Silt in Underground Engineering

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Yugui Yang ◽  
Feng Gao ◽  
Hongmei Cheng ◽  
Yuanming Lai ◽  
Xiangxiang Zhang
Keyword(s):  
Mechanical Characteristic ◽  
Stress Level ◽  
Strain Softening ◽  
Triaxial Compression ◽  
High Stress ◽  
Constitutive Models ◽  
Confining Pressure ◽  
Frozen Soil ◽  
Conventional Triaxial Compression ◽  
Shear Process

The researches on the mechanical characteristic and constitutive models of frozen soil have important meanings in structural design of deep frozen soil wall. In the present study, the triaxial compression and creep tests have been carried out, and the mechanical characteristic of frozen silt is obtained. The experiment results show that the deformation characteristic of frozen silt is related to confining pressure under conventional triaxial compression condition. The frozen silt presents strain softening in shear process; with increase of confining pressure, the strain softening characteristic gradually decreases. The creep curves of frozen silt present the decaying and the stable creep stages under low stress level; however, under high stress level, once the strain increases to a critical value, the creep strain velocity gradually increases and the specimen quickly happens to destroy. To reproduce the deformation behavior, the disturbed state elastoplastic and new creep constitutive models of frozen silt are developed. The comparisons between experimental results and calculated results from constitutive models show that the proposed constitutive models could describe the conventional triaxial compression and creep deformation behaviors of frozen silt.

scholarly journals Hydraulic properties and energy dissipation of deep hard rock under H-M coupling and cycling loads

2019 ◽  
Vol 23 (Suppl. 3) ◽  
pp. 935-942 ◽  
Author(s):  
Cheng-Han Zhang ◽  
Shuang You ◽  
Hong-Guang Ji ◽  
Fei Li ◽  
Hong-Tao Wang
Keyword(s):  
Acoustic Emission ◽  
Osmotic Pressure ◽  
Hydraulic Properties ◽  
Coupling Effect ◽  
High Stress ◽  
Confining Pressure ◽  
In Situ Stress ◽  
Dissipated Energy ◽  
Underground Engineering ◽  
Loading And Unloading

The permeability of deep rock is closely related to the stability and safety of underground engineering. The rocks in deep stratum are mostly with high stress and high osmotic pressure. Therefore, it is necessary to consider the coupling effect between porewater pressure and in situ stress on rock mass. A series of triaxial cyclic loading and unloading experiments under hydraulic-mechanics coupling conditions are carried out to studied the mechanical and hydraulic properties of granite in the depth of 1300 m to 1500 m. Especially, the effect of the disturbance on the permeability of fractured rocks are investigated by unloaded the confining pressure. Tests results presented that the stress-strain curves of deep granite showed typical brittle characteristics. The principal stress of granite exhibited a linear relationship under the high confining pressure of 34-40 MPa and high osmotic pressure of 13-15 MPa. Dissipated energy of the rock decreased to a relatively low level after 2-3 loading cycles and then slowly increased. Permeability showed a decreasing trend as the loading and unloading cycles increase. Finally, acoustic emission technology was used to monitor the fracture evolution in rocks, the acoustic emission signal released as the fractures develop and energy dissipated. The results would provide basic data for the exploitation and excavation in the deep galleries.

scholarly journals Acoustic Emission Simulation on Coal Specimen Subjected to Cyclic Loading

2020 ◽  
Vol 2020 ◽  
pp. 1-17
Author(s):  
Huiqiang Duan ◽  
Depeng Ma
Keyword(s):  
Numerical Simulation ◽  
Acoustic Emission ◽  
Cyclic Loading ◽  
Confining Pressure ◽  
Rock Masses ◽  
Coal Specimen ◽  
Cycle Number ◽  
Confining Pressures ◽  
Unloading Rate ◽  
Ae Counts

The damage and failure state of the loaded coal and rock masses is indirectly reflected by its acoustic emission (AE) characteristics. Therefore, it is of great significance to study the AE evolution of loaded coal and rock masses for the evaluation of damage degree and prediction of collapse. The paper mainly represents a numerical simulation investigation of the AE characteristics of coal specimen subjected to cyclic loading under three confining pressures, loading-unloading rates, and valley stresses. From the numerical simulation tests, the following conclusions can be drawn: (1) The final cycle number of coal specimen subjected to cyclic loading is significantly influenced by the confining pressure, followed the valley stress. With the increase in confining pressure or valley stress, the cycle number tends to increase. However, the loading-unloading rate has a little influence on it. (2) The AE counts of coal specimen subjected to cyclic loading are greatly influenced by the confining pressure and the valley stress. With the increase in the confining pressure, the cumulative AE counts at the 1st cycle tend to increase but decrease at a cycle before failure; with the decrease in the valley stress, the cumulative AE counts per cycle increase in the relatively quiet phase. However, the loading-unloading rate has a little influence on it. (3) The failure mode of coal specimen subjected to cyclic loading is significantly influenced by the confining pressure. Under the uniaxial stress state, there is an inclined main fractured plane in the coal specimen, under the confining pressures of 5 and 10 MPa, the coal specimen represents dispersion failure. The loading-unloading rate and valley stress have little influence on it. (4) The AE ratio is proposed, and its evolution can better reflect the different stages of coal specimen failure under cyclic loading. (5) The influence of confining pressure on the broken degree of coal specimen subjected to cyclic loading is analyzed, and the higher the confining pressure, the more broken the failed coal specimen.

scholarly journals The Effect of Confining Pressure on the Mechanical Properties of Sand–Ice Materials

1973 ◽  
Vol 12 (66) ◽  
pp. 469-481 ◽  
Author(s):  
Bernard D. Alkire ◽  
Orlando B. Andersland
Keyword(s):  
Axial Strain ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Silica Sand ◽  
Creep Tests ◽  
Ice Volume ◽  
Coulomb Failure ◽  
Confining Pressures ◽  
Sand Material ◽  
Cylindrical Samples

Cylindrical samples containing 0.59 mm to 0.84 mm diameter silica sand at about 97% and 55% ice saturation (the ratio of ice volume to sand pore volume) were tested at a temperature of −12° C in triaxial compression. Both constant axial strain-rate tests and step-stress creep tests provide information on the influence of confining pressure on the shear strength and creep behavior of the sand–ice material. Changes in the degree of ice saturation help show the influence of the ice matrix versus the sand material on the mechanical behavior. Data are discussed in terms of the Mohr–Coulomb failure law and creep theories. It is shown that the cohesive component of strength depends on response of the ice matrix, whereas the frictional component of strength responds in a manner very similar to unfrozen sand tested at high confining pressures. Experimental data show that creep rates decrease exponentially and creep strength increases with an increase in confining pressure.

scholarly journals Ice triaxial deformation and fracture

1994 ◽  
Vol 40 (135) ◽  
pp. 305-318 ◽  
Author(s):  
M.A. Rist ◽  
S.A.F Murrell
Keyword(s):  
Shear Fracture ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Maximum Principal Stress ◽  
Brittle Strength ◽  
Independent Evidence ◽  
Polycrystalline Ice ◽  
Confining Pressures ◽  
Pressure Independent ◽  
Ice Failure

AbstractAn experimental investigation into the mechanical behaviour of polycrystalline ice in triaxial compression has been conducted using conditions generally favourable to brittle fracture and microcracking. Under triaxial stresses at high strain rate, ice failure occurs by abrupt shear fracturing, generally inclined at about 45° to the maximum principal stress. At −20°C, such failure is suppressed by the imposition of a small confining pressure, allowing a transition to ductile-type flow accompanied by distributed microcracking, but at —40°C shear fracture persists under confinement of up to at least 50 MPa. For low confining pressures (< 10 MPa), brittle strength is strongly pressure-dependent; above this it is pressure-independent. Evidence is presented that suggests this may reflect a change from a fracture process influenced by friction to fracture initiated by localized yielding. Ductile yield strength is found to be little influenced by confining pressure despite the inhibition of cracking that leads to greatly contrasting observed crack densities. Flow conforms to the well-known power law for ice withQ= 69 J mol−1andn= 4.2 over the temperature range −20° to −4-5° C Under these conditions, microcracking in ice appears to remain remarkably stable and non-interacting.

Sign in / Sign up

Export Citation Format

Share Document