scholarly journals Electrochemical and Morphological Investigations of Ga Addition to Pt Electrocatalyst Supported on Carbon

2017 ◽  
Vol 2017 ◽  
pp. 1-15 ◽  
Author(s):  
Giordano T. Paganoto ◽  
Deise M. Santos ◽  
Tereza C. S. Evangelista ◽  
Marco C. C. Guimarães ◽  
Maria Tereza W. D. Carneiro ◽  
...  
Keyword(s):  
Electrochemical Impedance ◽  
Physicochemical Characterization ◽  
Face Centered Cubic ◽  
X Ray Diffraction ◽  
Precursor Method ◽  
Tem Analysis ◽  
X Ray ◽  
Transmission Electron ◽  
Face Centered

This paper is consisted in the synthesis of platinum-based electrocatalysts supported on carbon (Vulcan XC-72) and investigation of the addition of gallium in their physicochemical and electrochemical properties toward ethanol oxidation reaction (EOR). PtGa/C electrocatalysts were prepared through thermal decomposition of polymeric precursor method at a temperature of 350°C. Six different compositions were homemade: Pt50Ga50/C, Pt60Ga40/C, Pt70Ga30/C, Pt80Ga20/C, Pt90Ga10/C, and Pt100/C. These electrocatalysts were electrochemically characterized by cyclic voltammetry (CV), chronoamperometry (CA), chronopotentiometry (CP), and electrochemical impedance spectroscopy (EIS) in the presence and absence of ethanol 1.0 mol L−1. Thermogravimetric analysis (TGA), energy dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), and transmission electron microscopy (TEM) were also carried out for a physicochemical characterization of those materials. XRD results showed the main peaks of face-centered cubic Pt. The particle sizes obtained from XRD and TEM analysis range from 7.2 nm to 12.9 nm. The CV results indicate behavior typical of Pt-based electrocatalysts in acid medium. The CV, EIS, and CA data reveal that the addition of up to 31% of gallium to the Pt highly improves catalytic activity on EOR response when compared to Pt100/C.

Synthesis and Characterization of Nanocrystalline CeO2

2006 ◽  
Vol 306-308 ◽  
pp. 1103-1108
Author(s):  
Abdul Hadi ◽  
Iskandar Idris Yaacob
Keyword(s):  
Fine Particles ◽  
Gas Adsorption ◽  
Mesoporous Structure ◽  
Face Centered Cubic ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Face Centered ◽  
Adsorption Desorption

Nanocrystalline CeO2 has been synthesized at room temperature using water-in-oil (w/o) microemulsion technique. The structure and properties of the nanocrystalline CeO2 were characterized using X-ray diffraction (XRD), transmission electron microscopy (TEM), and gas adsorption desorption measurement. XRD results showed the synthesized CeO2 has a face centered cubic structure with crystallite size of about 5.2 nm. TEM observation also indicated the presence of nanometer sized particles of CeO2. Coarser particles were also observed due to agglomeration. Gas adsorption desorption isotherms showed the behavior of fine particles with mesoporous structure.

Synthesis and Characterization of Silver Nanowires

2013 ◽  
Vol 678 ◽  
pp. 212-216
Author(s):  
Subbaiyan Sugapriya ◽  
Rangarajalu Sriram ◽  
Sriram Lakshmi
Keyword(s):  
Silver Nanowires ◽  
Synthesis And Characterization ◽  
Face Centered Cubic ◽  
Capping Agent ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Face Centered ◽  
Fcc Structure

ABSTRACT Silver nanowires have been synthesized by polyol process with ethylene glycol as solvent and PVP as capping agent. The silver nanowires have been characterized by X-ray diffraction (XRD), Scanning electron microscopy (SEM), Energy-dispersive X-ray spectroscopy (EDX), and Transmission electron microscope (TEM) techniques. The prepared silver nanowires were found to exhibit face-centered cubic (fcc) structure. The diameter of the prepared silver nanowires have been found to lie in the range of 60 - 80 nm and the length of the wires have been observed to be in the range of 10-20 µm. The I-V characteristics have been carried out to study the conducting behavior of the prepared silver nanowires.

scholarly journals Diffraction studies on Ni–Co and Ni–Cr alloy thin films

1991 ◽  
Vol 6 (4) ◽  
pp. 749-754 ◽  
Author(s):  
A.R. Sethuraman ◽  
R.J. De Angelis ◽  
P.J. Reucroft
Keyword(s):  
Amorphous Structure ◽  
Face Centered Cubic ◽  
Limited Information ◽  
X Ray Diffraction ◽  
Tem Analysis ◽  
Alloy Films ◽  
X Ray ◽  
Cr Content ◽  
Transmission Electron ◽  
Face Centered

Alloy films of Ni–Co and Ni–Cr of compositional ratios 1:1, 1:3, and 3:1 deposited by vapor deposition were studied by Transmission Electron Microscopy (TEM) and X-Ray Diffraction (XRD). Results of TEM analysis on the Ni–Co alloy films indicated that the films were face-centered cubic (fcc) in structure. XRD results confirmed the TEM observations. TEM analysis of Ni–Cr alloy films showed that the films were body-centered cubic (bcc) in structure. With increase in the Cr content more than 25%, the material contained a higher fraction of an amorphous phase. XRD studies provide limited information owing to the quasi-amorphous structure of the films of high Cr content.

Structural, morphological, and magnetic study of nanocrystalline cobalt-copper powders synthesized by the polyol process

1995 ◽  
Vol 10 (6) ◽  
pp. 1546-1554 ◽  
Author(s):  
G.M. Chow ◽  
L.K. Kurihara ◽  
K.M. Kemner ◽  
P.E. Schoen ◽  
W.T. Elam ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Face Centered Cubic ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Copper Powders ◽  
Face Centered ◽  
Increasing Temperature ◽  
X Ray Absorption

Nanocrystalline CoxCu100−x (4 ⋚ x ⋚ 49 at. %) powders were prepared by the reduction of metal acetates in a polyol. The structure of powders was characterized by x-ray diffraction (XRD), transmission electron microscopy (TEM), high resolution transmission electron microscopy (HRTEM), extended x-ray absorption fine structure (EXAFS) spectroscopy, solid-state nuclear magnetic resonance (NMR) spectroscopy, and vibrating sample magnetometry (VSM). As-synthesized powders were composites consisting of nanoscale crystallites of face-centered cubic (fcc) Cu and metastable face-centered cubic (fcc) Co. Complementary results of XRD, HRTEM, EXAFS, NMR, and VSM confirmed that there was no metastable alloying between Co and Cu. The NMR data also revealed that there was some hexagonal-closed-packed (hcp) Co in the samples. The powders were agglomerated, and consisted of aggregates of nanoscale crystallites of Co and Cu. Upon annealing, the powders with low Co contents showed an increase in both saturation magnetization and coercivity with increasing temperature. The results suggested that during preparation the nucleation of Cu occurred first, and the Cu crystallites served as nuclei for the formation of Co.

scholarly journals Exploration of the Antimicrobial and Catalytic Properties of Gold Nanoparticles Greenly Synthesized by Cryptolepis buchanani Roem. and Schult Extract

2020 ◽  
Vol 2020 ◽  
pp. 1-11
Author(s):  
Kamonpan Wongyai ◽  
Phitchayapak Wintachai ◽  
Rasimate Maungchang ◽  
Parawee Rattanakit
Keyword(s):  
Staphylococcus Aureus ◽  
Gold Nanoparticles ◽  
Analytical Techniques ◽  
Average Diameter ◽  
Face Centered Cubic ◽  
Tem Analysis ◽  
X Ray ◽  
Transmission Electron ◽  
Vis Spectroscopy ◽  
Face Centered

A green, simple, and rapid synthesis of gold nanoparticles using plant extract, Cryptolepis buchanani Roem. and Schult, and their applications are first described in this paper. The formation of gold nanoparticles was visually observed by the appearance of a ruby red color, which was further indicated by an absorption peak at 530 nm in UV-Vis spectroscopy. Optimization of reaction parameters for the gold nanoparticles was also investigated. Various analytical techniques were employed as part of the process of characterizing the resulting gold nanoparticles. Fourier transform infrared (FTIR) analysis revealed that the phenol compounds present in the extract were responsible for gold(III) reduction and stabilization of gold nanoparticles. Transmission electron microscopy (TEM) analysis showed that the gold nanoparticles were spherical in shape with an average diameter of 11 nm. Powder X-ray diffraction (XRD) pattern indicated that the green synthesis approach produced highly crystalline, face-centered cubic gold nanoparticles. Energy-dispersive X-ray spectroscopy (EDS) measurements confirmed the presence of elemental gold in the prepared nanoparticles. The negative zeta potential value of gold nanoparticles was found to be -30.28 mV. The green synthesized gold nanoparticles expressed effective antibacterial activity against Staphylococcus aureus, methicillin-resistant Staphylococcus aureus, and Acinetobacter baumannii and exhibited an excellent catalytic property in terms of its reduction ability of methylene blue.

Photocatalytic Analysis and Characterization of Zn2SnO4 Nanoparticles Synthesized via Hydrothermal Method with Na2CO3 Mineralizer

2010 ◽  
Vol 97-101 ◽  
pp. 19-22 ◽  
Author(s):  
Yu Shiang Wu ◽  
Wen Ku Chang ◽  
Min Jou
Keyword(s):  
Photocatalytic Activity ◽  
Hydrothermal Process ◽  
Face Centered Cubic ◽  
X Ray Diffraction ◽  
Visible Absorption ◽  
Transmission Electron ◽  
Excellent Photocatalytic Activity ◽  
Face Centered ◽  
Xrd Patterns

Zinc stannate Zn2SnO4 (ZTO) nanoparticles were synthesized via a hydrothermal process utilizing sodium carbonate (Na2CO3) as a weak basic mineralizer. The samples were hydrothermally treated at 150, 200, and 250oC for 48 h. The X-ray diffraction (XRD) patterns show that the highly-crystalline ZTO nanostructure could be formed in a well-dispersed manner for the 250°C sample at a particle size of less than 50 nm. As determined from transmission electron microscopy (TEM) results, ZTO nanoparticles are face-centered cubic single crystals agglomerated together. The Raman spectra results showed that the ZTO nanocrystals have a spinel structure. Furthermore, photocatalytic activity was tested with methylene blue (MB) by UV irradiation. The ZTO synthesized by the 2 M Na2CO3 mineralizer at 250oC demonstrated excellent photocatalytic activity. The ZTO treated three different ways had three distinct UV-Visible absorption curves, which directly influences their corresponding photocatalytic activity.

Synthesis and Characterization of Cobalt-Nickel Nanowires Formed under External Magnetic Field

2015 ◽  
Vol 799-800 ◽  
pp. 120-124 ◽  
Author(s):  
Mary Donnabelle L. Balela ◽  
Lalaine M. Dulin ◽  
Erica A. Garcia ◽  
M. Janelle H. Tica
Keyword(s):  
Magnetic Field ◽  
External Magnetic Field ◽  
Face Centered Cubic ◽  
X Ray Diffraction ◽  
X Ray ◽  
Hexagonal Close Packed ◽  
Cobalt Nickel ◽  
Nickel Nanowires ◽  
Face Centered

Cobalt-nickel (Co-Ni) nanowires were formed by electroless deposition in ethylene glycol under external magnetic field. The effects of initial Co (II) and Ni (II) concentration on the surface and morphology of the synthesized nanowires were investigated by x-ray diffraction (XRD) and scanning electron microscope (SEM) respectively. An increase in the Co (II) concentration resulted in increase in diameter of the nanowires. However, the length of nanowires was observed to decrease. Higher Co (II) concentration resulted in a mixture of hexagonal close-packed and face-centered cubic Co-Ni nanowires. X-ray diffraction revealed that crystal growth occurred when the nanowires are annealed at 653 K for 10h.

scholarly journals Sonochemically Prepared GdWNFs/CNFs Nanocomposite As An Electrode Material For The Electrochemical Detection of Antibiotic Drug in Water Bodies

2021 ◽  
Author(s):  
Manikanta P ◽  
Hari Prasad B R ◽  
Sanjay B P ◽  
Sandeep S ◽  
Santhosh A S ◽  
...  
Keyword(s):  
Electrochemical Impedance ◽  
Differential Pulse ◽  
Electrochemical Sensing ◽  
Pencil Graphite Electrode ◽  
X Ray Diffraction ◽  
Standard Samples ◽  
Tem Analysis ◽  
X Ray ◽  
Transmission Electron ◽  
Antibiotic Drug

Abstract The work demonstrates the development of an electrochemical sensor for quantification of Chloramphenicol (CA) using pencil graphite electrode (PGE) modified with Gadolinium tungstate nano flakes and carbon nano fibers composite (PGE/GWNfs/CNFs). The composite was further characterized and confirmed by X-ray diffraction (XRD), energy-dispersive X-ray spectroscopy (EDS), Transmission electron microscopy (TEM) analysis. The prepared GWNfs/CNFs nano composite was fabricated by drop casting method to get PGE/GWNfs/CNFs working electrode. The modified electrode is then analyzed by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and differential pulse voltammetry (DPV) methods for its electrochemical and electrocatalytic property. The electrochemical investigation of developed sensor shows enhanced activity towards electro-oxidation of CA. The DPV studies revealed high efficacy characteristics such as sensitivity in the range 0.03984 µA µM-1cm-2, selectivity, good linear range (5-50 μM), and low detection limit (0.4 μM). The study benchmarks the use of GWNfs/CNFs as an excellent transducer material in electrochemical sensing of CA in standard samples thus, it finds an efficient potential application in the analysis of CA in environment sample analysis.

scholarly journals Development of Ternary and Quaternary Catalysts for the Electrooxidation of Glycerol

2012 ◽  
Vol 2012 ◽  
pp. 1-6 ◽  
Author(s):  
L. M. Artem ◽  
D. M. Santos ◽  
A. R. De Andrade ◽  
K. B. Kokoh ◽  
J. Ribeiro
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Cyclic Voltammetry ◽  
Pechini Method ◽  
Particle Sizes ◽  
Face Centered Cubic ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Face Centered

This work consisted in the preparation of platinum-based catalysts supported on carbon (Vulcan XC-72) and investigation of their physicochemical and electrochemical properties. Catalysts of the C/Pt-Ni-Sn-Me (Me = Ru or Ir) type were prepared by the Pechini method at temperature of350∘C. Four different compositions were homemade: C/Pt60Sn10Ni30, C/Pt60Sn10Ni20Ru10, C/Pt60Sn10Ni10Ru20, and C/Pt60Sn10Ni10Ir20. These catalysts were electrochemically and physically characterized by cyclic voltammetry (CV), chronoamperometry (CA) in the presence of glycerol 1.0 mol dm-3, X-ray diffraction (XRD), and high-resolution transmission electron microscopy (HRTEM). XRD results showed the main peaks of face-centered cubic Pt. The particle sizes obtained from XRD and HRTEM experiments were close to values ranging from 3 to 8.5 nm. The CV results indicate behavior typical of Pt-based catalysts in acid medium. The CV and CA data reveal that quaternary catalysts present the highest current density for the electrooxidation of glycerol.

Synthesis and Characterization of Structure Controlled Nano-cobalt Particles

2002 ◽  
Vol 755 ◽  
Author(s):  
Shiqiang Hui ◽  
Mingzhong Wu ◽  
Shihui Ge ◽  
Dajing Yan ◽  
Y.D. Zhang ◽  
...  
Keyword(s):  
Grain Size ◽  
Magnetic Properties ◽  
Silica Coating ◽  
Face Centered Cubic ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Average Grain Size ◽  
Wet Chemical ◽  
Face Centered

ABSTRACTNanostructured cobalt particles with and without a ceramic coating have been synthesized using a wet chemical method. The structure and magnetic properties of synthesized powder were characterized using x-ray diffraction (“XRD”), high-resolution transmission electron microscopy (“HRTEM”), and a Quantum Design (SQUID) magnetometer. The cobalt nanoparticles are of either face-centered cubic (“fcc”) and/or hexagonally close-packed (“hcp”) crystalline structures. The average grain size is ∼14 nm for cobalt (either fcc or hcp) with an amorphous silica coating, and the average grain size is ∼9 nm for hcp cobalt and 26 nm for fcc cobalt without a silica coating. The effect of annealing temperature on grain size and magnetic properties are addressed.

Sign in / Sign up

Export Citation Format

Share Document