scholarly journals Simulation of Chloride Ingress through Surface-Coated Concrete during Migration Test Using Finite-Difference and Finite-Element Method

2017 ◽  
Vol 2017 ◽  
pp. 1-12 ◽  
Author(s):  
Seyoon Yoon
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Diffusion Coefficient ◽  
Finite Difference ◽  
Polymer Surface ◽  
Ionic Concentration ◽  
Surface Coatings ◽  
Chloride Ingress ◽  
Simulation Results ◽  
Element Method

Polymer surface coatings are commonly used to enhance the corrosion resistance of concrete structures in saline environments to ionic diffusivity; this diffusivity can be determined by migration tests. This paper presents the simulation of the effects of the surface coatings on migration tests by solving the Nernst-Planck/Poisson model using both finite-difference method and finite-element method. These two numerical methods were compared in terms of their accuracy and computational speed. The simulation results indicate that the shapes of ionic profiles after migration tests depend on the effectiveness of surface coatings. This is because highly effective surface coatings can cause a high ionic concentration at the interface between coating and concrete. The simulation results were also compared to homogenized cases where a homogenized diffusion coefficient is employed. The result shows that the homogenized diffusion coefficient cannot represent the diffusivity of the surface-coated concrete.

scholarly journals An Eulerian finite element method for PDEs in time-dependent domains

2019 ◽  
Vol 53 (2) ◽  
pp. 585-614 ◽  
Author(s):  
Christoph Lehrenfeld ◽  
Maxim Olshanskii
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Finite Difference ◽  
Numerical Method ◽  
Computational Domain ◽  
Physical Domain ◽  
Finite Element Approximations ◽  
Additional Stabilization ◽  
Background Mesh ◽  
Element Method

The paper introduces a new finite element numerical method for the solution of partial differential equations on evolving domains. The approach uses a completely Eulerian description of the domain motion. The physical domain is embedded in a triangulated computational domain and can overlap the time-independent background mesh in an arbitrary way. The numerical method is based on finite difference discretizations of time derivatives and a standard geometrically unfitted finite element method with an additional stabilization term in the spatial domain. The performance and analysis of the method rely on the fundamental extension result in Sobolev spaces for functions defined on bounded domains. This paper includes a complete stability and error analysis, which accounts for discretization errors resulting from finite difference and finite element approximations as well as for geometric errors coming from a possible approximate recovery of the physical domain. Several numerical examples illustrate the theory and demonstrate the practical efficiency of the method.

A study of azimuthal electromagnetic wave LWD based on self-adaptive hp finite element method

2018 ◽  
Vol 32 (34n36) ◽  
pp. 1840073
Author(s):  
Hui Li ◽  
Yi-Bo Jiang ◽  
Jian-Wen Cai
Keyword(s):  
Numerical Simulation ◽  
Finite Element Method ◽  
Finite Element ◽  
Electromagnetic Wave ◽  
Real Time ◽  
Simulation Results ◽  
Peak Value ◽  
Element Method ◽  
Self Adaptive ◽  
Hp Finite Element

Azimuthal electromagnetic wave logging-while-drilling (LWD) technology can detect weak electromagnetic wave signal and realize real-time resistivity imaging. It has great values to reduce drilling cost and increase drilling rate. In this paper, self-adaptive hp finite element method (FEM) has been used to study the azimuthal resistivity LWD responses in different conditions. Numerical simulation results show that amplitude attenuation and phase shift of directional electromagnetic wave signals are closely related to induced magnetic field and azimuthal angle. The peak value and polarity of geological guidance signals can be used to distinguish reservoir interface and achieve real-time geosteering drilling. Numerical simulation results also show the accuracy of the self-adaptive hp FEM and provide physical interpretation of peak value and polarity of the geological guidance signals.

A Tunable THz Plasmonic Waveguide Based on Graphene Coated Bow-tie Nanowire with High Mode Confinement

2020 ◽  
Vol 12 ◽  
Author(s):  
Jue Wang ◽  
Tao Ma ◽  
Xu Wang ◽  
Fang Wang
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Electric Field ◽  
High Density ◽  
Plasmonic Waveguide ◽  
Field Distributions ◽  
Simulation Results ◽  
Photonic Circuit ◽  
Bow Tie ◽  
Element Method

Background: : A THz Plasmonic Waveguide Based on Graphene Coated Bow-tie Nanowire (TPW-GCBN) is proposed. The waveguide characteristics are investigated by using Finite Element Method (FEM). The influence of the geometric parameters on propagation constants, electric field distributions, effective mode areas, and propagation lengths are obtained numerically. The performance tunability of TPW-GCBN is also studied by adjusting the Fermi energy (FE). The simulation results show that the TPW-GCBN has better mode confinement ability. The TPW-GCBN has potential applications in high density integration of photonic circuit for the future tunable micro nano optoelectronic devices. Surface plasmon polaritons (SPPs) based waveguides have been widely used to enhance the local electric fields. It also has the capability of manipulating electromagnetic fields on the deep-subwavelength. Objective:: The waveguide characteristics of a THz Plasmonic Waveguide Based on Graphene Coated Bow-tie Nanowire (TPW-GCBN) should be investigated. The tunability of TPW-GCBN should be studied by adjusting the chemical potential (FE) which can be changed by the voltage. Method: : The mode analysis and parameter sweep in Finite Element Method (FEM) were used to simulate the TPW-GCBN for analyzing effective refractive index (neff), electric field distributions, normalized mode areas (Am), propagation length (Lp) and figure of merit (FoM). Results: : At 5 THz, Aeff of λ2/14812, Lp of ~2 μm and FoM of 25 can be achieved. The simulation results show that the TPW-GBN has good mode confinement ability and flexible tunability. Conclusion:: The TPW-GBN provides a new freedom to manipulate the graphene surface plasmons, and leads to new applications in high density integration of photonic circuit for tunable integrated optical devices.

Dynamic tensile process of blended fabric using finite element method

2020 ◽  
Vol 32 (5) ◽  
pp. 707-724
Author(s):  
Xuzhong Su ◽  
Xinjin Liu
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Experimental Testing ◽  
Woven Fabrics ◽  
Weft Yarn ◽  
Tensile Fracture ◽  
Content Type ◽  
Tensile Process ◽  
Simulation Results ◽  
Element Method

PurposeTensile property is one basic mechanics performance of the fabric. In general, not only the tensile values of the fabric are needed, but also the dynamic changing process under the tension is also needed. However, the dynamic tensile process cannot be included in the common testing methods by using the instruments after fabric weaving.Design/methodology/approachBy choosing the weft yarn and warp yarn in the fabric as the minimum modeling unit, 1:1 finite element model of the whole woven fabrics was built by using AutoCAD software according to the measured geometric parameters of the fabrics and mechanical parameters of yarns. Then, the fabric dynamic tensile process was simulated by using the ANSYS software. The stress–strain curve along the warp direction and shrinkage rate curve along the weft direction of the fabrics were simulated. Meanwhile, simulation results were verified by comparing to the testing results.FindingsIt is shown that there are four stages during the fabric tensile fracture process along the warp direction under the tension. The first stage is fabric elastic deformation. The second stage is fabric yield deformation, and the change rate of stress begins to slow down. The third stage is fiber breaking, and the change of stress fluctuates since the breaking time of the fibers is different. The fourth stage is fabric breaking.Originality/valueIn this paper, the dynamic tensile process of blended woven fabrics was studied by using finite element method. Although there are differences between the simulation results and experimental testing results, the overall tendency of simulation results is the same as the experimental testing results.

scholarly journals New CZM for Interfacial Crack Growth

2017 ◽  
Vol 2017 ◽  
pp. 1-8 ◽  
Author(s):  
Huifen Peng ◽  
Yujie Song ◽  
Ye Xia
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Crack Growth ◽  
Interface Crack ◽  
Interfacial Crack ◽  
Structure Design ◽  
Zone Model ◽  
Simulation Results ◽  
The Impact ◽  
Element Method

The cohesive zone model (CZM) has been widely used for numerical simulations of interface crack growth. However, geometrical and material discontinuities decrease the accuracy and efficiency of the CZM when based on the conventional finite element method (CFEM). In order to promote the development of numerical simulation of interfacial crack growth, a new CZM, based on the wavelet finite element method (WFEM), is presented. Some fundamental issues regarding CZM of interface crack growth of double cantilever beam (DCB) testing were studied. The simulation results were compared with the experimental and simulation results of CFEM. It was found that the new CZM had higher accuracy and efficiency in the simulation of interface crack growth. At last, the impact of crack initiation length and elastic constants of material on interface crack growth was studied based on the new CZM. These results provided a basis for reasonable structure design of composite material in engineering.

The Numerical Simulation of Effective Elastic Response for WC-Co Cemented Carbide

2015 ◽  
Vol 1096 ◽  
pp. 417-421
Author(s):  
Pei Luan Li ◽  
Zi Qian Huang
Keyword(s):  
Numerical Simulation ◽  
Finite Element Method ◽  
Finite Element ◽  
Theoretical Model ◽  
Material Properties ◽  
Cemented Carbide ◽  
Elastic Response ◽  
The Finite Element Method ◽  
Simulation Results ◽  
Element Method

By the use of finite element method, this paper predicts the effects of the shapes of reinforcements with different ductility (Co) on the effective elastic response for WC-Co cemented carbide. This paper conducts a comparative study on the material properties obtained through theoretical model, numerical simulation and experimental observations. Simulation results indicate that the finite element method is more sophisticated than the theoretical prediction.

Sign in / Sign up

Export Citation Format

Share Document