scholarly journals Investigation of the Effects of Anisotropic Flow of Pore Water and Multilayered Soils on Three-Dimensional Consolidation Characteristics

2017 ◽  
Vol 2017 ◽  
pp. 1-11 ◽  
Author(s):  
Arpan Laskar ◽  
Sujit Kumar Pal
Keyword(s):  
Pore Water ◽  
Three Dimensional ◽  
Surface Settlement ◽  
Coefficient Of Consolidation ◽  
Consolidation Process ◽  
Soil Layers ◽  
Anisotropic Flow ◽  
Practical Engineering ◽  
Consolidating Soil ◽  
Multilayered Soils

Many practical engineering problems are seriously different from the assumptions which are considered for one-dimensional consolidation test and need to concentrate on three-dimensional consolidation of soil under different boundary conditions. In this study three-dimensional consolidation tests are performed with four different anisotropic flow conditions of pore water and fifteen different combinations of horizontal layered soils. Twelve different three-dimensional consolidation tests are also performed with different soils, surrounded by anisotropic vertical soil layers on two opposite sides. From these studies, it is observed that the anisotropic flow of pore water does not have any effect on initial and final surface settlement of soil but has a significant effect during the consolidation process. The anisotropic flow of pore water during the consolidation process has an immense effect on the coefficient of consolidation. Horizontal layered soil has a great effect on both surface settlement and the rate of settlement. Vertical soil layers on two opposite sides of consolidative soil have an immense effect on the horizontal movements of consolidating soil, finally affecting the resultant vertical settlement of soil. Vertical anisotropic surrounding soil layers also have an effect on the rate of consolidation settlement.

scholarly journals Experimental insights into consolidation rates during one-dimensional loading with special reference to excess pore water pressure

2020 ◽  
Vol 15 (12) ◽  
pp. 3571-3591
Author(s):  
Bartłomiej Szczepan Olek
Keyword(s):  
Pore Water ◽  
Large Scale ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Small Scale ◽  
Coefficient Of Consolidation ◽  
Consolidation Process ◽  
Factors Affecting ◽  
Fine Grained ◽  
Fine Grained Soil

AbstractConsolidation rate has significant influence on the settlement of structures founded on soft fine-grained soil. This paper presents the results of a series of small-scale and large-scale Rowe cell consolidation tests with pore water pressure measurements to investigate the factors affecting the consolidation process. Permeability and creep/resistance structure factors were considered as the governing factors. Intact and reconstituted marine clay from the Polish Carpathian Foredeep basin as well as clay–sand mixtures was examined in the present study. The fundamental relationship correlating consolidation degrees based on compression and pore water pressure was assessed to indicate the nonlinear soil behaviour. It was observed that the instantaneous consolidation parameters vary as the process progresses. The instantaneous coefficient of consolidation first drastically increases or decreases with increase in the degree of consolidation and stabilises in the middle stage of the consolidation; it then decreases significantly due to viscoplastic effects occurring in the soil structure. Based on the characteristics of the relationship between coefficient of consolidation and degree of dissipation at the base, the consolidation range that complies with theoretical assumptions was established. Furthermore, the influence of coarser fraction in clay–sand mixtures in controlling the consolidation rates is discussed.

Calculation of Consolidation Coefficient and Percent Consolidation from Measured Pore Water Pressure of Soft Clay

2011 ◽  
Vol 250-253 ◽  
pp. 1889-1892
Author(s):  
Yong Mou Zhang ◽  
Jian Chang Zhao
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Soft Soil ◽  
Soft Clay ◽  
Coefficient Of Consolidation ◽  
Consolidation Process ◽  
Consolidation Coefficient

Consolidation coefficient and percent consolidation of soft clay were calculated according to the measured pore water pressure of a project in Pudong Shanghai. Calculated coefficient of consolidation was one magnitude larger than the experimental one. This was in conformity with the actual consolidation process of dynamically-consolidated soft soil.

scholarly journals Numerical Evaluation of The Nonlinear Behavior of Soil-Pile Interaction Under The Effect of Coupled Static-Dynamic Loads

2021 ◽  
Author(s):  
Duaa Al-Jeznawi ◽  
ISMACAHYADI Mohamed Jais ◽  
Bushra S. Albusoda
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Three Dimensional ◽  
Ground Surface ◽  
Frictional Resistance ◽  
Saturated Soil ◽  
Shaking Table ◽  
Physical Models ◽  
Soil Layers

Abstract Liquefaction of saturated soil layers is one of the most common causes of structural failure during earthquakes. Liquefaction occurs as a result of increasing pore water pressure, whereby the rise in water pressure occurs due to unexpected change in stress state under short-term loading, i.e., shaking during an earthquake. Thus, general failure occurs when the soil softens and eliminates its stiffness against the uplift pressure from the stability of the subsurface structure. In this case, the condition of soil strata is considered undrained because there is not enough time for the excess pore water pressure to dissipate when a sudden load is applied. To represent the non-linear characteristics of saturated sand under seismic motions in Kobe and Ali Algharbi earthquakes, the computational model was simulated using the UBCSAND model. The current study was carried out by adopting three-dimensional-based finite element models that were evaluated by shaking table tests of a single pile model erected in the saturated soil layers. The experimental data were utilized to estimate the liquefaction and seismicity of soil deposits. According to the results obtained from the physical models and simulations, this proposed model accurately simulates the liquefaction phenomenon and soil-pile response. However, there are some differences between the experiment and the computational analyses. Nonetheless, the results showed good agreement with the general trend in terms of deformation, acceleration, and liquefaction ratio. Moreover, the displacement of liquefied soil around the pile was captured by the directions of vectors generated by numerical analysis, which resembled a worldwide circular flow pattern. The results revealed that during the dynamic excitation, increased pore water pressure and subsequent liquefaction caused a significant reduction in pile frictional resistance. Despite this, positive frictional resistance was noticed through the loose sand layer (near the ground surface) until the soil softened completely. It is worth mentioning that the pile exhibited excessive settlement which may attribute to the considerable reduction, in the end, bearing forces which in turn mobilizing extra end resistance.

Disorganization of a hole tone feedback loop by an axisymmetric obstacle on a downstream end plate

2014 ◽  
Vol 757 ◽  
pp. 908-942 ◽  
Author(s):  
K. Matsuura ◽  
M. Nakano
Keyword(s):  
Nozzle Exit ◽  
Passive Control ◽  
Control Method ◽  
Three Dimensional ◽  
Acoustic Power ◽  
Shear Layers ◽  
Mean Velocity ◽  
End Plate ◽  
Air Jet ◽  
Practical Engineering

AbstractThis study investigates the suppression of the sound produced when a jet, issued from a circular nozzle or hole in a plate, goes through a similar hole in a second plate. The sound, known as a hole tone, is encountered in many practical engineering situations. The mean velocity of the air jet $\def \xmlpi #1{}\def \mathsfbi #1{\boldsymbol {\mathsf {#1}}}\let \le =\leqslant \let \leq =\leqslant \let \ge =\geqslant \let \geq =\geqslant \def \Pr {\mathit {Pr}}\def \Fr {\mathit {Fr}}\def \Rey {\mathit {Re}}u_0$ was $6\text {--}12\ \mathrm{m}\ {\mathrm{s}}^{-1}$. The nozzle and the end plate hole both had a diameter of 51 mm, and the impingement length $L_{im}$ between the nozzle and the end plate was 50–90 mm. We propose a novel passive control method of suppressing the tone with an axisymmetric obstacle on the end plate. We find that the effect of the obstacle is well described by the combination ($W/L_{im}$, $h$) where $W$ is the distance from the edge of the end plate hole to the inner wall of the obstacle, and $h$ is the obstacle height. The tone is suppressed when backflows from the obstacle affect the jet shear layers near the nozzle exit. We do a direct sound computation for a typical case where the tone is successfully suppressed. Axisymmetric uniformity observed in the uncontrolled case is broken almost completely in the controlled case. The destruction is maintained by the process in which three-dimensional vortices in the jet shear layers convect downstream, interact with the obstacle and recursively disturb the jet flow from the nozzle exit. While regions near the edge of the end plate hole are responsible for producing the sound in the controlled case as well as in the uncontrolled case, acoustic power in the controlled case is much lower than in the uncontrolled case because of the disorganized state.

Three‐Dimensional Numerical Investigation of Pore Water Pressure and Deformation of Pumped Aquifer Systems

Ground Water ◽  
2019 ◽  
Vol 58 (2) ◽  
pp. 278-290 ◽  
Author(s):  
Yun Zhang ◽  
Xuexin Yan ◽  
Tianliang Yang ◽  
Jichun Wu ◽  
Jianzhong Wu
Keyword(s):  
Numerical Investigation ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Three Dimensional ◽  
Aquifer Systems

scholarly journals An educational software for teaching soil consolidation

2017 ◽  
Author(s):  
Gonzalo García Ros ◽  
Manuel Cánovas Vidal ◽  
Juan Francisco Sánchez Pérez ◽  
Iván Alhama Manteca
Keyword(s):  
Educational Software ◽  
Low Cost ◽  
Surface Settlement ◽  
Excess Pore Pressure ◽  
Soil Consolidation ◽  
Depth Of Penetration ◽  
Consolidation Process ◽  
Prefabricated Vertical Drains ◽  
Vertical Drains ◽  
Graphical Environment

The educational tool SICOMED_3D has been created to simulate problems of soil consolidation by prefabricated vertical drains. Thanks to its nice interface of windows, the introduction of data is very fast and easy for the students, while providing users with simple handling and powerful calculations. Its graphical environment allows to get representations of the excess pore pressure, local settlements and total surface settlement. SICOMED_3D can also generate an animation that recreates the evolution of the surface settlement during the consolidation process. The software presents, like commercial softwares, the most common options (e.g., save and open cases files, save animations and representations, etc.). Although the program is created to be used in several fields, among others as an engineering or research tool, the main use of interest for this work is for educational purposes. Another important application is as low-cost laboratory practices, as students can experiment by modifying the soil properties, including the depth of penetration of the vertical drain, in a quick, simple and intuitive way.

scholarly journals ANALISIS PENGGUNAAN PREFABRICATED VERTICAL DRAINS (PVD) PADA TANAH LEMPUNG LUNAK YANG TERDAPAT LAPISAN LENSA

2020 ◽  
Vol 3 (1) ◽  
pp. 119
Author(s):  
Andreyan Prasetio ◽  
Aniek Prihatiningsih
Keyword(s):  
Soft Soil ◽  
Soil Improvement ◽  
Cohesive Soils ◽  
Consolidation Process ◽  
Prefabricated Vertical Drains ◽  
Soil Layers ◽  
Vertical Drains ◽  
Vertical Drain ◽  
Installation Depth ◽  
Consolidation Time

Problem that often occurs in soft cohesive soils is settlement caused by consolidation process. If  construction activities doing when the soils has not been consolidated, settlement can occur. To accelerate  the consolidation process, soil improvement are usually do, one method of soil improvement to accelarate the consolidation process is vertical drain using prefabricated vertical drains (PVD). The soft soil layers in the field are not always continuous, sometimes found soft soil layers that have a lens layer. In this study, will discuss about the settlement and consolidation time of soft  soil layers that have a lens layer which has been improved by PVD with 1 meter distance. Infrastructure that stand on a location that is installed by PVD is taxiway and loading by Airbus A380 aircraft of 18,22ton/m2. Analysis using the 1 dimensional consolidation theory of Terzaghi. For PVD installation to a depth of 50 meters, preloading settlement of 234,80 cm with a consolidation time of  2260 days for the square pattern PVD and 1918 days for triangle pattern PVD. Post loading settlement for PVD installation depth of 50 meters by 2,50 cm. AbstrakMasalah yang sering terjadi pada tanah kohesif dan lunak adalah penurunan yang disebabkan proses konsolidasi. Penurunan dapat menyebabkan keretakan pada struktur konstruksi yang berada di atasnya. Jika suatu kegiatan konstruksi dilakukan saat tanah belum terkonsolidasi, maka konstruksi tersebut dapat mengalami penurunan.. Untuk mempercepat proses konsolidasi biasanya dilakukan perbaikan tanah, salah satu metode perbaikan tanah untuk mempercepat proses konsolidasi yaitu vertical drain dengan menggunakan prefabricated vertical drains (PVD). Lapisan tanah lunak yang terdapat di lapangan tidak selalu kontinu, terkadang ditemukan lapisan tanah lunak yang terdapat lapisan lensa. Pada penelitian ini, penulis akan membahas mengenai waktu konsolidasi yang dibutuhkan oleh lapisan tanah kohesif dan lunak yang terdapat lapisan lensa yang telah diperbaiki dengan menggunakan PVD berjarak 1 meter. Infrastruktur yang berdiri di atas lokasi yang dipasang PVD berupa taxiway dengan beban berupa pesawat Airbus A380 sebesar 18,22 ton/m2. Analisis dilakukan menggunakan teori konsolidasi 1 dimensi Terzaghi. Untuk pemasangan PVD hingga kedalaman 50 meter diperoleh penurunan pra pembebanan sebesar 234,80 cm dengan waktu konsolidasi selama 2260 hari untuk pemasangan PVD pola persegi dan selama 1918 hari untuk pola segitiga . Penurunan pasca pembebanan untuk pemasangan PVD hingga kedalaman 50 meter sebesar 2,5 cm.

scholarly journals Design and Optimization of Multiple Circumferential Casing Grooves Distribution Considering Sweep and Lean Variations on the Blade Tip

Energies ◽  
2018 ◽  
Vol 11 (9) ◽  
pp. 2401
Author(s):  
Weimin Song ◽  
Yufei Zhang ◽  
Haixin Chen
Keyword(s):  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Distribution ◽  
Stall Margin ◽  
Design Point ◽  
Casing Treatment ◽  
Design And Optimization ◽  
Practical Engineering ◽  
Engineering Strategy ◽  
Blade Tip

This paper focuses on the design and optimization of the axial distribution of the circumferential groove casing treatment (CGCT). Effects of the axial location of multiple casing grooves on the flow structures are numerically studied. Sweep and lean variations are then introduced to the blade tip, and their influences on the grooves are discussed. The results show that the ability of the CGCT to relieve the blockage varies with the distribution of grooves, and the three-dimensional blading affects the performance of both the blade and the CGCT. Accordingly, a multi-objective optimization combining the CGCT design with the sweep and lean design is conducted. Objectives, including the total pressure ratio and the adiabatic efficiency, are set at the design point; meanwhile, the choking mass flow and the near-stall performance are constrained. The coupling between the CGCT and the blade is improved, which contributes to an optimal design point performance and a sufficient stall margin. The sweep and lean in the tip redistribute the spanwise and chordwise loading, which enhances the ability of the CGCT to improve the blade’s performance. This work shows that the present CGCT-blade integrated optimization is a practical engineering strategy to develop the working capacity and efficiency of a compressor blade while achieving the stall margin extension.

Possibilistic Uncertainty Quantification in 1-D Consolidation Problems

2021 ◽  
Author(s):  
Djamalddine Boumezerane
Keyword(s):  
Uncertainty Quantification ◽  
Probability Distributions ◽  
Uncertainty Propagation ◽  
Possibility Distribution ◽  
Coefficient Of Consolidation ◽  
Consolidation Process ◽  
Possibility Distributions ◽  
Coverage Function ◽  
The One ◽  
Measure Of Uncertainty

Abstract In this study, we use possibility distribution as a basis for parameter uncertainty quantification in one-dimensional consolidation problems. A Possibility distribution is the one-point coverage function of a random set and viewed as containing both partial ignorance and uncertainty. Vagueness and scarcity of information needed for characterizing the coefficient of consolidation in clay can be handled using possibility distributions. Possibility distributions can be constructed from existing data, or based on transformation of probability distributions. An attempt is made to set a systematic approach for estimating uncertainty propagation during the consolidation process. The measure of uncertainty is based on Klir's definition (1995). We make comparisons with results obtained from other approaches (probabilistic…) and discuss the importance of using possibility distributions in this type of problems.

Sign in / Sign up

Export Citation Format

Share Document