scholarly journals Bioactive Potential of 3D-Printed Oleo-Gum-Resin Disks:B. papyrifera,C. myrrha, andS. benzoinLoading Nanooxides—TiO2, P25, Cu2O, and MoO3

2017 ◽  
Vol 2017 ◽  
pp. 1-16 ◽  
Author(s):  
Diogo José Horst ◽  
Sergio Mazurek Tebcherani ◽  
Evaldo Toniolo Kubaski ◽  
Rogério de Almeida Vieira
Keyword(s):  
Pure State ◽  
Fused Deposition Modeling ◽  
Metal Oxide Nanoparticles ◽  
Scanning Calorimetry ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Microscopy Analysis ◽  
3D Printed ◽  
Bioactive Potential ◽  
Hot Melt

This experimental study investigates the bioactive potential of filaments produced via hot melt extrusion (HME) and intended for fused deposition modeling (FDM) 3D printing purposes. The oleo-gum-resins from benzoin, myrrha, and olibanum in pure state and also charged with 10% of metal oxide nanoparticles, TiO2, P25, Cu2O, and MoO3, were characterized by ultraviolet-visible (UV-Vis) and Fourier transform infrared (FTIR) spectroscopy, energy-dispersive X-ray microanalysis (EDXMA), scanning electron microscopy (SEM), and differential scanning calorimetry (DSC). Disks were 3D-printed into model geometries (10 × 5 mm) and the disk-diffusion methodology was used for the evaluation of antimicrobial and antifungal activity of materials in study against the clinical isolates:Staphylococcus aureus, Pseudomonas aeruginosa, Escherichia coli, andCandida albicans. Due to their intrinsic properties, disks containing resins in pure state mostly prevent surface-associated growth; meanwhile, disks loaded with 10% oxides prevent planktonic growth of microorganisms in the susceptibility assay. The microscopy analysis showed that part of nanoparticles was encapsulated by the biopolymeric matrix of resins, in most cases remaining disorderly dispersed over the surface of resins. Thermal analysis shows that plant resins have peculiar characteristics, with a thermal behavior similar to commercial available semicrystalline polymers, although their structure consists of a mix of organic compounds.

Development of three-dimensional printing filaments based on poly(lactic acid)/hydroxyapatite composites with potential for tissue engineering

2021 ◽  
pp. 002199832098856
Author(s):  
Marcela Piassi Bernardo ◽  
Bruna Cristina Rodrigues da Silva ◽  
Luiz Henrique Capparelli Mattoso
Keyword(s):  
Tissue Engineering ◽  
Lactic Acid ◽  
Fused Deposition Modeling ◽  
Three Dimensional ◽  
Poly Lactic Acid ◽  
Scanning Calorimetry ◽  
Three Dimensional Printing ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
3D Printed

Injured bone tissues can be healed with scaffolds, which could be manufactured using the fused deposition modeling (FDM) strategy. Poly(lactic acid) (PLA) is one of the most biocompatible polymers suitable for FDM, while hydroxyapatite (HA) could improve the bioactivity of scaffold due to its chemical composition. Therefore, the combination of PLA/HA can create composite filaments adequate for FDM and with high osteoconductive and osteointegration potentials. In this work, we proposed a different approache to improve the potential bioactivity of 3D printed scaffolds for bone tissue engineering by increasing the HA loading (20-30%) in the PLA composite filaments. Two routes were investigated regarding the use of solvents in the filament production. To assess the suitability of the FDM-3D printing process, and the influence of the HA content on the polymer matrix, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and scanning electron microscopy (SEM) were performed. The HA phase content of the composite filaments agreed with the initial composite proportions. The wettability of the 3D printed scaffolds was also increased. It was shown a greener route for obtaining composite filaments that generate scaffolds with properties similar to those obtained by the solvent casting, with high HA content and great potential to be used as a bone graft.

Effect of heat treatment on crystallinity and mechanical properties of flexible structures 3D printed with fused deposition modeling

2021 ◽  
pp. 152808372110649
Author(s):  
Ajay Jayswal ◽  
Sabit Adanur
Keyword(s):  
Heat Treatment ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Fused Deposition Modeling ◽  
Scanning Calorimetry ◽  
Fused Deposition ◽  
Dog Bone ◽  
Heat Treated ◽  
Deposition Modeling ◽  
3D Printed

Fused Deposition Modeling (FDM) is a widely used 3D printing technique, which works based on the principle of melted polymer extrusion through nozzle(s) and depositing them on a build plate layer by layer. However, products manufactured with this method lack proper mechanical strength. In this work, 2/1 twill weave fabric structures are 3D printed using poly (lactic) acid (PLA). The ultimate tensile strength in the warp and weft directions and the modulus (stiffnesses) are measured for non-heat-treated (NHT) samples. The printed samples were heat-treated (HT) to improve the strength and stiffness. The variation in ultimate tensile strength is statistically insignificant in warp direction at all temperatures; however, the tensile strength in weft direction decreased after heat treatment. The modulus in warp direction increased by 31% after heat treatment while in the weft direction it decreased after heat treatment. Differential scanning calorimetry (DSC) tests showed the highest crystallinity at 125°C. The properties of the twill fabrics were compared with a standard dog-bone (DB) specimen using uniaxial tensile tests, Differential scanning calorimetry tests, and optical microscope (OM). For dog-bone specimens, the maximum values of crystallinity, ultimate tensile strength, and modulus were found to be at 125°C. The maximum crystallinity percentages are higher than that of the NHT samples. The ultimate tensile strength of NHT DB specimen 3D printed in horizontal orientation improved after heat treatment. The ultimate tensile strength of DB samples in vertical directions increased after heat treatment as well. The stiffness increased in both directions for DB samples.

Silane-Treated Muscovite as Reinforcement for 3D-Printed ABS via Fused Deposition Modeling

2021 ◽  
Vol 877 ◽  
pp. 67-72
Author(s):  
Niño B. Felices ◽  
Bryan B. Pajarito
Keyword(s):  
Thermal Properties ◽  
Fused Deposition Modeling ◽  
Acrylonitrile Butadiene Styrene ◽  
Mechanical And Thermal Properties ◽  
Scanning Calorimetry ◽  
Mechanical Reinforcement ◽  
Fused Deposition ◽  
The Matrix ◽  
Deposition Modeling ◽  
3D Printed

Epoxysilane-treated muscovite (ETM) was used as reinforcing filler to 3D-printed acrylonitrile butadiene styrene (ABS) via fused deposition modeling (FDM). Its effects to the mechanical and thermal properties of ABS were investigated. ETM was loaded at 1, 3, and 5wt%. ABS/ETM composites were characterized via scanning electron microscopy (SEM), tensile test, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Mechanical reinforcement of ABS was observed for ABS/ETM composites loaded at 1 and 3 wt% wherein it was noted that the tensile strength and elastic modulus increased by up to 83.6% and 76.6%, respectively. Reinforcement was brought by interfacial adhesion of ETM with the ABS matrix. There was a sharp decline in mechanical properties for ABS/ETM composites loaded at 5wt% due to agglomeration of ETM in the matrix and discontinuities in the printed layers. The glass transition temperature (Tg) of ABS increased and the onset of its degradation shifted towards higher temperatures with the addition of ETM. It can be concluded that the addition of ETM to ABS for FDM 3D printing improved its mechanical and thermal properties.

Effect of Silane-Treated Wollastonite on Mechanical and Thermal Properties of 3D-Printed ABS via Fused Deposition Modeling

2021 ◽  
Vol 877 ◽  
pp. 61-66
Author(s):  
Niño B. Felices ◽  
Bryan B. Pajarito
Keyword(s):  
Thermal Properties ◽  
Fused Deposition Modeling ◽  
Acrylonitrile Butadiene Styrene ◽  
Filler Loading ◽  
Mechanical And Thermal Properties ◽  
Scanning Calorimetry ◽  
Fused Deposition ◽  
Uniform Dispersion ◽  
Deposition Modeling ◽  
3D Printed

The effect of the addition of epoxysilane-treated wollastonite (ETW) to the mechanical and thermal properties of 3D-printed acrylonitrile butadiene styrene (ABS) via fused deposition modeling (FDM) was investigated. The loading of ETW was varied at 1, 3, and 5wt%. The 3D-printed composites were evaluated by scanning electron microscopy (SEM) tensile test, shore D hardness, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The addition of ETW increases the tensile strength, elastic modulus, and toughness of ABS by up to 46.6, 56.2, and 53.7 %, respectively. The shore D hardness increases with increasing ETW. Morphological analysis show that this improvement in mechanical properties is a result of the high aspect ratio of the fillers, the uniform dispersion of ETW in the ABS matrix, and the orientation of ETW particles toward the direction of tensile stress. The glass transition temperature (Tg) of the composites increases and the onset of degradation slightly shifted to higher temperature with an increase in filler loading. The addition of ETW to ABS matrix in FDM 3D printing improved the mechanical and thermal properties of ABS.

Biodegradable 3D Printed Polymer Microneedles for Transdermal Drug Delivery

2018 ◽  
Author(s):  
Michael A. Luzuriaga ◽  
Danielle R. Berry ◽  
John C. Reagan ◽  
Ronald A. Smaldone ◽  
Jeremiah J. Gassensmith
Keyword(s):  
Drug Delivery ◽  
3D Printing ◽  
Transdermal Drug Delivery ◽  
Fused Deposition Modeling ◽  
Fused Deposition ◽  
Modeling Software ◽  
Deposition Modeling ◽  
3D Printed ◽  
Microfabrication Technique ◽  
Mechanical Strengths

Biodegradable polymer microneedle (MN) arrays are an emerging class of transdermal drug delivery devices that promise a painless and sanitary alternative to syringes; however, prototyping bespoke needle architectures is expensive and requires production of new master templates. Here, we present a new microfabrication technique for MNs using fused deposition modeling (FDM) 3D printing using polylactic acid, an FDA approved, renewable, biodegradable, thermoplastic material. We show how this natural degradability can be exploited to overcome a key challenge of FDM 3D printing, in particular the low resolution of these printers. We improved the feature size of the printed parts significantly by developing a post fabrication chemical etching protocol, which allowed us to access tip sizes as small as 1 μm. With 3D modeling software, various MN shapes were designed and printed rapidly with custom needle density, length, and shape. Scanning electron microscopy confirmed that our method resulted in needle tip sizes in the range of 1 – 55 µm, which could successfully penetrate and break off into porcine skin. We have also shown that these MNs have comparable mechanical strengths to currently fabricated MNs and we further demonstrated how the swellability of PLA can be exploited to load small molecule drugs and how its degradability in skin can release those small molecules over time.

scholarly journals Controlling magnetic properties of 3D-printed magnetic elastomer structures via fused deposition modeling

AIP Advances ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 025223
Author(s):  
Thomas M. Calascione ◽  
Nathan A. Fischer ◽  
Thomas J. Lee ◽  
Hannah G. Thatcher ◽  
Brittany B. Nelson-Cheeseman
Keyword(s):  
Magnetic Properties ◽  
Fused Deposition Modeling ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
3D Printed

scholarly journals Pressure Orientation-Dependent Recovery of 3D-Printed PLA Objects with Varying Infill Degree

Polymers ◽  
2021 ◽  
Vol 13 (8) ◽  
pp. 1275 ◽  
Author(s):  
Guido Ehrmann ◽  
Andrea Ehrmann
Keyword(s):  
Shape Memory ◽  
Fused Deposition Modeling ◽  
Static Load ◽  
Shape Memory Polymer ◽  
Applied Pressure ◽  
Poly Lactic Acid ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Load Tests ◽  
3D Printed

Poly(lactic acid) is not only one of the most often used materials for 3D printing via fused deposition modeling (FDM), but also a shape-memory polymer. This means that objects printed from PLA can, to a certain extent, be deformed and regenerate their original shape automatically when they are heated to a moderate temperature of about 60–100 °C. It is important to note that pure PLA cannot restore broken bonds, so that it is necessary to find structures which can take up large forces by deformation without full breaks. Here we report on the continuation of previous tests on 3D-printed cubes with different infill patterns and degrees, now investigating the influence of the orientation of the applied pressure on the recovery properties. We find that for the applied gyroid pattern, indentation on the front parallel to the layers gives the worst recovery due to nearly full layer separation, while indentation on the front perpendicular to the layers or diagonal gives significantly better results. Pressing from the top, either diagonal or parallel to an edge, interestingly leads to a different residual strain than pressing from front, with indentation on top always firstly leading to an expansion towards the indenter after the first few quasi-static load tests. To quantitatively evaluate these results, new measures are suggested which could be adopted by other groups working on shape-memory polymers.

Sign in / Sign up

Export Citation Format

Share Document