scholarly journals 3D Reconstruction of the Surface Using a Standard Camera

2017 ◽  
Vol 2017 ◽  
pp. 1-11 ◽  
Author(s):  
Dalibor Martišek

This paper deals with3Dreconstructions of series of partially focussed images. Some of these methods are known in case of images which were acquired in small field of view (by confocal microscope or CCD camera, e.g.). In this case, recorded images do not differ in any geometrical transformation from each other. In case of larger samples (oversized for microscope or CCD camera), it is necessary to use wider viewing field (standard cameras, e.g.), and taken images primarily differ in scaling but may also differ in shifting and rotation too. These images cannot be used for reconstruction directly; they must be registered; that is, we must determine all transformations which the images differ and eliminate their effects. There are several ways to do this. This paper deals with the registration based on phase correlation. After this registration, it is necessary to identify the sharp parts and to compose a2Dand3Dmodel. Present methods are very sensitive to noise and their results are not satisfactory in many cases. We introduce a new method for3Dreconstruction which is significantly better.

Scanning ◽  
2017 ◽  
Vol 2017 ◽  
pp. 1-8 ◽  
Author(s):  
Dalibor Martišek ◽  
Hana Druckmüllerová

Methods of fracture surface 3D reconstruction from a series of partially focused images acquired in a small field of view (e.g., by confocal microscope or CCD camera) are well known. In this case, projection rays can be considered parallel and recorded images do not differ in any geometrical transformation from each other. In the case of larger samples (oversized for microscope or CCD camera), it is necessary to use a wider viewing field (e.g., standard cameras); taken images primarily differ in scaling but may also differ in shifting and rotation. These images cannot be used for reconstruction directly; they must be registered; that is, we must determine all transformations in which the images differ and eliminate their effects. There are several ways to do this. This paper deals with the registration based on phase correlation.


1994 ◽  
Vol 144 ◽  
pp. 593-596
Author(s):  
O. Bouchard ◽  
S. Koutchmy ◽  
L. November ◽  
J.-C. Vial ◽  
J. B. Zirker

AbstractWe present the results of the analysis of a movie taken over a small field of view in the intermediate corona at a spatial resolution of 0.5“, a temporal resolution of 1 s and a spectral passband of 7 nm. These CCD observations were made at the prime focus of the 3.6 m aperture CFHT telescope during the 1991 total solar eclipse.


2017 ◽  
Vol 72 (3) ◽  
pp. 267.e1-267.e12 ◽  
Author(s):  
M. Schulze ◽  
K. Reimann ◽  
A. Seeger ◽  
U. Klose ◽  
U. Ernemann ◽  
...  

Author(s):  
Junmin Zhao ◽  
Cong Nie ◽  
Guannan Chang ◽  
Meibo Lyu ◽  
Xinguo Li

The air-to-ground missile with strapdown seeker may have the problems, including small field of view(FOV), limited overload, and fall angle constraint. To solve the above mentioned problem, a phased guidance scheme is proposed. In this scheme, the attack trajectory is divided into the following six stages, including glided stage, fall angle constraint stage, target acquisition and adjustment stage, terminal guidance stage and blind zone stage. The glided stage is designed to increase range, the terminal fall angle is attained ahead of time at fall angle constraint stage. The aim of target acquisition and adjustment stage is to adjust the missile attitude, so that the target will fall within the FOV of the seeker. It creates good condition to capture the target for strapdown seeker. In the terminal stage, the guidance law of proportional navigation and attitude track are used to fit the needs of FOV constraint and attack accuracy. The simulation result shows that the project trajectory can solve the application of attacking moving targets for air-to-ground missile with strapdown seeker under multi constraints.


Author(s):  
C. W. Han ◽  
S. Cho ◽  
B. Han

Moire´ interferometry is a full-field optical method that has high displacement, strain and spatial resolution. The method has been used extensively for deformation analyses in the various fields of mechanics. Special considerations arise when deformation measurements of tiny specimens or tiny regions of larger specimens are sought. The relative displacements within a small field of view will be small (even if the strains are not small), so the number of morie´ fringes might not be enough for an accurate analysis.


2019 ◽  
pp. 20190020
Author(s):  
Aik Hao Ng ◽  
Mohammed S. Alqahtani ◽  
Layal K. Jambi ◽  
Sarah L. Bugby ◽  
John E. Lees ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document