scholarly journals Flexural Properties of PVC/Bamboo Composites under Static and Dynamic-Thermal Conditions: Effects of Composition and Water Absorption

2017 ◽  
Vol 2017 ◽  
pp. 1-8 ◽  
Author(s):  
Shahril Anuar Bahari ◽  
Warren J. Grigsby ◽  
Andreas Krause
Keyword(s):  
Mechanical Properties ◽  
Thermal Analysis ◽  
Dynamic Mechanical Thermal Analysis ◽  
Elevated Temperatures ◽  
Flexural Modulus ◽  
Thermal Conditions ◽  
Flexural Properties ◽  
Particle Sizes ◽  
Flexural Performance

Polyvinyl chloride (PVC)/bamboo composites have been prepared and assessed for their use in interior and exterior load-bearing applications. PVC composites were formed by compounding PVC with different bamboo particle sizes and loadings. The mechanical properties of these composites were determined at both ambient and elevated temperatures and after long-term water soaking. Analysis revealed that bamboo incorporation improved the PVC composite flexural modulus which was also observed with dynamic mechanical-thermal analysis on heating composites toca.70°C. Addition of 25% and 50% bamboo particles increases flexural modulus by 80% with dependency on whether fine (<75 μm) or coarse (<1 mm) particles were used. On water soaking to saturation, composites had water weight uptakes of 10%, with reduced flexural properties obtained for all water-soaked composites. Nonetheless, the results of this study show that PVC/bamboo composites achieve the minimum flexural performance of ASTM D 6662, indicating potential for their use in exterior applications.

The Effect of Fiber Size on the Mechanical Properties of Bertam/Unsaturated Polyester Composites

2015 ◽  
Vol 761 ◽  
pp. 52-56
Author(s):  
M.H. Norhidayah ◽  
Arep Hambali ◽  
M.Y. Yuhazri
Keyword(s):  
Mechanical Properties ◽  
Fiber Length ◽  
Unsaturated Polyester ◽  
Flexural Modulus ◽  
Flexural Properties ◽  
Fiber Size ◽  
Polyester Composites

The aim of this paper was the effects of different fiber size on tensile and flexural properties. Preparation of thermoset unsaturated polyester reinforced with particle Bertam (Eugeissona tristis) was done by hand layout method. Bertam/polyester composites containing Bertam fiber of different sizes, i.e., 15, 120 and 284 μm were prepared. For each composite, eight specimens were tested to evaluate the mechanical properties. It was found that composite reinforced with Bertam having the shortest fiber length, i.e, 15 μm showed the highest tensile and flexural modulus, which were 204.14 MPa and 1826.78 MPa, respectively.

Mechanical properties of polyester/corn husk fibre composite produced using vacuum infusion technique

2021 ◽  
Vol 29 (9_suppl) ◽  
pp. S1532-S1540
Author(s):  
Shibly Shadik Mir Md ◽  
Ming Yeng Chan ◽  
Seong Chun Koay
Keyword(s):  
Mechanical Properties ◽  
Fibre Composite ◽  
Alkali Treatment ◽  
Flexural Modulus ◽  
Fibre Length ◽  
Flexural Properties ◽  
Vacuum Infusion ◽  
Corn Husk ◽  
Plastic Composite ◽  
Polyester Composites

Issues pertaining to deforestation, environmental pollution and natural wastes are increasing day by day. These issues can be resolved by introducing a new composite material, in which natural waste is used as fibre and as a replacement of wood plastic composite. The different lengths (3, 6 and 9 cm) of corn husk fibre filled polyester composites were produced using the vacuum infusion method. Several mechanical properties of these polyester composites, such as tensile and flexural properties, were evaluated. The results revealed that both the tensile and flexural properties of polyester composites increased with increment of corn husk fibre length from 3 to 6 cm. However, the results decreased for 9 cm of fibre length filled composites. Similar trends were recorded after alkali treatment of the corn husk fibre filled polyester composites. The alkali treatment with sodium hydroxide had improved the tensile strength (33%), Young’s modulus (23%), elongation (14%), flexural strength (42%) and flexural modulus (8.5%) of the polyester/corn husk fibre composites with 6 cm of fibre length by enhancing the mechanical interlocking bonding between treated corn husk fibres and polyester.

Polyimide Composites from ‘Salt-Like’ Solution Precursors

2001 ◽  
Vol 13 (4) ◽  
pp. 235-250 ◽  
Author(s):  
Roberto J Cano ◽  
Tan H Hou ◽  
Erik S Weiser ◽  
Terry L St Clair
Keyword(s):  
Mechanical Properties ◽  
Carbon Fibre ◽  
Compression Strength ◽  
Elevated Temperatures ◽  
Flexural Modulus ◽  
Matrix Composites ◽  
Compression After Impact ◽  
Open Hole ◽  
Polyimide Composites ◽  
Polyimide Matrix

Four NASA Langley-developed polyimide matrix resins, LaRC™-IA, LaRC™-IAX, LaRC™-8515 and LaRC™-PETI-5, were produced via a ‘salt-like’ process developed by Unitika Ltd. The salt-like solutions (65% solids in NMP) were prepregged onto Hexcel IM7 carbon fibre using the NASA LaRC™ multipurpose tape machine. Process parameters were determined and composite panels fabricated. The temperature dependent volatile depletion rates, the thermal crystallization behaviour and the resin rheology were characterized. Composite moulding cycles were developed which consistently yielded well consolidated, void-free laminated parts. Composite mechanical properties such as the short beam shear strength; the longitudinal and transverse flexural strength and flexural modulus; the longitudinal compression strength and modulus; and the open hole compression strength and compression after impact strength were measured at room temperature and elevated temperatures. The processing characteristics and the composite mechanical properties of the four intermediate modulus carbon fibre/polyimide matrix composites were compared to existing data on the same polyimide resin systems and IM7 carbon fibre manufactured via poly(amide acid) solutions (30–35% solids in NMP). This work studies the effects of varying the synthetic route on the processing and mechanical properties of the polyimide composites.

IM7/LARC™-IAX-3 Polyimide Composites

1998 ◽  
Vol 10 (2) ◽  
pp. 193-206 ◽  
Author(s):  
T H Hou ◽  
T L St Clair
Keyword(s):  
Mechanical Properties ◽  
High Performance ◽  
Elevated Temperatures ◽  
Flexural Modulus ◽  
Longitudinal Tensile Strength ◽  
Molecular Weights ◽  
Short Beam ◽  
Beam Shear ◽  
Carrier Solvent ◽  
Langley Research Center

LARC™-IAX-3 (Langley Research Center™-improved adhesive experimental resin-3) aromatic polyimide, based on oxydiphthalic anhydride, 3,′4-oxydianiline (3,′4-ODA) and 1,4-phenylenediamine ( p-PDA), was evaluated as a matrix for high-performance composites. Four poly(amide acid) solutions in either N-methypyrrolidone or γ-butyrolactone, end-capped with phthalic anhydride to various theoretical molecular weights, were synthesized. Unidirectional prepreg was fabricated from each of the four resins utilizing NASA-Langley’s multipurpose prepreg machine. The temperature-dependent volatile depletion rates, the thermal crystallization behaviour and the resin rheology were characterized. Based on this information, a composite moulding cycle was developed which consistently yielded well consolidated void-free laminate parts. Composite mechanical properties such as short beam shear strength, longitudinal and transverse flexural strength and flexural modulus, longitudinal tensile strength and notched and unnotched compression strengths were measured at room temperature (RT) and elevated temperatures. Similar properties were obtained independent of the carrier solvent used during matrix resin synthesis. These mechanical properties were superior to those previously measured for IM7/LARC™-IA and IM7/LARC™-IAX composites. The enhanced mechanical properties were attributed to the substitution of 25% 3,′4-ODA by p-PDA in the LARC™-IA imide backbones.

scholarly journals Effect of Long Term Service at Elevated Temperatures on Mechanical Properties of Manaurite XM Reformer Tubes

2016 ◽  
Vol 16 (4) ◽  
pp. 38-44
Author(s):  
J. Łabanowski ◽  
M. Jurkowski ◽  
M. Landowski
Keyword(s):  
Mechanical Properties ◽  
Elevated Temperatures ◽  
Cast Steel ◽  
Internal Diameter ◽  
Term Operation ◽  
Static Tensile ◽  
Different Shapes ◽  
Reformer Tubes ◽  
The Relationship

Abstract Microstructure transformations occur in the Manaurite XM cast steel tubes during long-term operation in the reformer furnace were revealed and described. The relationship between mechanical properties, an increase of internal diameter of the tube and microstructure degradation is discussed. Static tensile test was performed on two types of samples with different shapes. It has been shown differences in the results of tests and an explanation of this phenomenon.

Mechanical Properties of X80 Grade UOE Pipe for Long-Term Exposure at Elevated Temperature

2004 ◽  
Author(s):  
Ryuji Muraoka ◽  
Mitsuhiro Okatsu ◽  
Nobuyuki Ishikawa ◽  
Shigeru Endo ◽  
Shinichi Kakihara ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Elevated Temperatures ◽  
Mechanical Tests ◽  
Heat Treatments ◽  
Oil Sand ◽  
Operation Condition ◽  
Long Time ◽  
Simulated Condition ◽  
Installation Cost

Recently, X80 grade UOE pipes have been planned to apply to steam injecting oil sand recovery systems to increase the volume of steam to be injected and lowering installation cost. The pipes for systems are subjected to high temperature for a long time, such as 350-C, for 20 years. Before real applications of the pipes, it is important to ensure the reliability of the pipes during and after long-term operations. In this study, in order to establish simulation conditions for 350-C × 20 years of operation, the change in microstructure and resulting mechanical properties of X80 grade pipes after a long-term exposure at elevated temperatures were investigated. Then, mechanical properties of the pipes subjected to the established simulated condition were examined. Change in the microstructure was quite small after exposure of 400-C and lower temperatures. Tensile strengths of the base metal and seam weld after up to 400-C of heat treatment can be arranged with the Larson-Miller parameter composed with temperature and holding time of the heat treatments. Therefore, heat treatments at 400-C for shorter than 20 years can be simulation conditions for the operation condition of the systems. As a result of mechanical tests simulating long-term exposure, satisfied performance of X80 grade pipes can be obtained.

scholarly journals Flexural Behavior of CFRP Laminate at Elevated Temperature

2017 ◽  
Vol 2 (3) ◽  
pp. 330-334
Author(s):  
Rzgar M. Abdalrahman
Keyword(s):  
Elevated Temperatures ◽  
Flexural Modulus ◽  
Peak Load ◽  
Test Method ◽  
Flexural Behavior ◽  
Bending Test ◽  
Effect Of Temperature ◽  
Flexural Properties ◽  
Flexural Behaviour ◽  
Cfrp Laminate

A carbon fibre reinforced polymer (CFRP) laminate forms the surface part of an integrally heated tool. It was made up of carbon non-crimp triaxial fibre and SR8100 epoxy in accordance to the stacking sequence of [(0, ±45)/ (90, ±45)] S, using the resin infusion (RI) method. The laminate is heated up to 90ºC when the tool is operated; therefore under-standing the effect of temperature on the flexural properties is quite significant. This experimental study is carried out to investigate the flexural behaviour of the CFRP laminate and finding its flexural properties under the effect of elevated temperatures. For this purpose, various CFRP specim-ens were prepared and tested, using three point bending test method, at different temperature levels from room temperature to 90ºC. The results show that each of the flexural peak load, modulus and strength of the laminate decreases consistently with the increase of temperature. Also the laminate becomes slightly more flexible and significant loss occurs in its flexural modulus when the temperature elevates from 75ºC to 90ºC. The reduction in the flexural behaviour of CFRP is imputed to thermal softening of the epoxy polymer matrix whenever becomes closer to (HDT).

scholarly journals Manufacturing of Porous Polycaprolactone Prepared with Different Particle Sizes and Infrared Laser Sintering Conditions: Microstructure and Mechanical Properties

2014 ◽  
Vol 6 ◽  
pp. 640496 ◽  
Author(s):  
G. V. Salmoria ◽  
D. Hotza ◽  
P. Klauss ◽  
L. A. Kanis ◽  
C. R. M. Roesler
Keyword(s):  
Mechanical Properties ◽  
Energy Density ◽  
Laser Energy ◽  
Flexural Modulus ◽  
Selective Laser Sintering ◽  
Polymeric Materials ◽  
Laser Sintering ◽  
Laser Energy Density ◽  
Particle Sizes ◽  
Mechanical Devices

The techniques of Rapid Prototyping, also known as Additive Manufacturing, have prompted research into methods of manufacturing polymeric materials with controlled porosity. This paper presents the characterization of the structure and mechanical properties of porous polycaprolactone (PCL) fabricated by Selective Laser Sintering (SLS) using two different particle sizes and laser processing conditions. The results of this study indicated that it is possible to control the microstructure, that is, pore size and degree of porosity, of the polycaprolactone matrix using the SLS technique, by varying the particle size and laser energy density, obtaining materials suitable for different applications, scaffolds and drug delivery and fluid mechanical devices. The specimens manufactured with smaller particles and higher laser energy density showed a higher degree of sintering, flexural modulus, and fatigue resistance when compared with the other specimens.

Sign in / Sign up

Export Citation Format

Share Document