scholarly journals The Structure and Flexural Properties of Typha Leaves

2017 ◽  
Vol 2017 ◽  
pp. 1-9 ◽  
Author(s):  
Jingjing Liu ◽  
Zhihui Zhang ◽  
Zhenglei Yu ◽  
Yunhong Liang ◽  
Xiujuan Li ◽  
...  
Keyword(s):  
Leaf Blade ◽  
High Strength ◽  
Structure Design ◽  
Bending Test ◽  
Flexural Properties ◽  
Low Density ◽  
High Porosity ◽  
Cross Sectional ◽  
Bionic Engineering ◽  
Lightweight Structure

The Typha leaf has a structure of lightweight cantilever beam, exhibiting excellent mechanical properties with low density. Especially, the leaf blade evolved high strength and low density with high porosity. In this paper, the structure of Typha leaf was characterized by microcomputed tomography (Micro-CT) and scanning electron microscopy (SEM), and the relationship with flexural properties was analyzed. The three-point bending test was performed on leaves to examine flexural properties, which indicated that the flexural properties vary from the base to the apex in gradient. The cross-sectional geometry shape of the leaf blade presented a strong influence on the optimized flexural stiffness. The load carrying capacity of the leaf depended on the development level of the epidermal tissue, the vascular bundle, the mechanical tissue, and the geometric properties. The investigation can be the basis for lightweight structure design and the application in the bionic engineering field.

Analysis of reinforcement efficiency and microscopic characterization of glass and carbon roving geometry in prestressed concrete composites

2021 ◽  
pp. 002199832110133
Author(s):  
Richard Haas ◽  
Till Quadflieg ◽  
Oleg Stolyarov
Keyword(s):  
Prestressed Concrete ◽  
Ct Scanning ◽  
Bending Test ◽  
Flexural Properties ◽  
Cross Sectional ◽  
Four Point Bending ◽  
Reinforcement Efficiency ◽  
The Cross ◽  
Sectional Shape

In this work, the reinforcement efficiency of concrete composites prestressed with glass and carbon rovings was studied. Prestressed concrete composites samples were prepared at a prestress level one-third the maximum tensile strength of the roving. The flexural properties of the manufactured composites were determined using a four-point bending test. Additionally, changes in the cross-sectional shape of the reinforcing rovings in the initial and prestressed states were analyzed using CT scanning and optical microscopy. The results showed that prestressing significantly affected the flexural properties of the concrete composites. Thus, the limit of proportionality increased by 1.26 and 1.85 for a composite reinforced with glass and carbon roving, respectively. The maximum flexural strength increased by approximately 1.2 times for both reinforcing rovings. The change in the cross-sectional shape of the reinforcing roving during prestressing enhances the efficiency of prestressed concrete composites.

The stabilization of B.C.C. Cu in Cu/Nb nanolayered composites

1996 ◽  
Vol 54 ◽  
pp. 228-229
Author(s):  
H. Kung ◽  
A.J. Griffin ◽  
Y.C. Lu ◽  
K.E. Sickafus ◽  
T.E. Mitchell ◽  
...  
Keyword(s):  
Electrical Resistivity ◽  
Layer Thickness ◽  
Volume Fraction ◽  
Ion Beam ◽  
High Strength ◽  
Cross Sectional ◽  
Metastable Structure ◽  
High Resolution Tem ◽  
Potential Improvement ◽  
Two Phases

Materials with compositionally modulated structures have gained much attention recently due to potential improvement in electrical, magnetic and mechanical properties. Specifically, Cu-Nb laminate systems have been extensively studied mainly due to the combination of high strength, and superior thermal and electrical conductivity that can be obtained and optimized for the different applications. The effect of layer thickness on the hardness, residual stress and electrical resistivity has been investigated. In general, increases in hardness and electrical resistivity have been observed with decreasing layer thickness. In addition, reduction in structural scale has caused the formation of a metastable structure which exhibits uniquely different properties. In this study, we report the formation of b.c.c. Cu in highly textured Cu/Nb nanolayers. A series of Cu/Nb nanolayered films, with alternating Cu and Nb layers, were prepared by dc magnetron sputtering onto Si {100} wafers. The nominal total thickness of each layered film was 1 μm. The layer thickness was varied between 1 nm and 500 nm with the volume fraction of the two phases kept constant at 50%. The deposition rates and film densities were determined through a combination of profilometry and ion beam analysis techniques. Cross-sectional transmission electron microscopy (XTEM) was used to examine the structure, phase and grain size distribution of the as-sputtered films. A JEOL 3000F high resolution TEM was used to characterize the microstructure.

Determination of the metal toughness components in impact-bending test

2018 ◽  
Vol 84 (12) ◽  
pp. 68-72
Author(s):  
A. B. Maksimov ◽  
I. P. Shevchenko ◽  
I. S. Erokhina
Keyword(s):  
Crack Growth ◽  
Specific Energy ◽  
Crack Formation ◽  
Crack Nucleation ◽  
Scale Effects ◽  
Linear Equations ◽  
Bending Test ◽  
Cross Sectional ◽  
Two Samples ◽  
Sample Width

A method for separating the work of impact into two parts - the work of the crack nucleation and that of crack growth - which consists in testing two samples with the same stress concentrators and different cross-sectional dimensions at the notch site is developed. It is assumed that the work of crack nucleation is proportional to the width of the sample face on which the crack originates and the specific energy of crack formation, whereas the work of the crack growth is proportional to the length of crack development and the specific crack growth energy. In case of the sample fracture upon testing, the crack growth length is assumed equal to the sample width. Data on the work of fracture of two samples and their geometrical dimensions at the site of the notch are used to form a system of two linear equations in two unknowns, i.e., the specific energy of crack formation and specific energy of crack growth. The determined specific energy values are then used to calculate the work of crack nucleation and work of crack growth. The use of the analytical method improves the accuracy compared to graphical - extrapolative procedures. The novelty of the method consists in using one and the same form of the notch in test samples, thus providing the same conditions of the stress-strain state for crack nucleation and growth. Moreover, specimens with different cross-section dimensions are used to eliminate the scale effects. Since the specific energy of the crack nu-cleation and specific energy of the crack growth are independent of the scale factor, they are determined only by the properties of the metal. Introduction the specific energy of crack formation and growth makes possible to assign a specific physical meaning to the fracture energy.

Loading rate effect on fracture behavior of fiber reinforced high strength concrete using a semi-circular bending test

2020 ◽  
Vol 240 ◽  
pp. 117681
Author(s):  
Mehran Aziminezhad ◽  
Sahand Mardi ◽  
Pouria Hajikarimi ◽  
Fereidoon Moghadas Nejad ◽  
Amir H. Gandomi
Keyword(s):  
High Strength Concrete ◽  
Fracture Behavior ◽  
Loading Rate ◽  
High Strength ◽  
Rate Effect ◽  
Bending Test ◽  
Fiber Reinforced ◽  
Strength Concrete

scholarly journals Optimization of whole-genome sequencing of Plasmodium falciparum from low-density dried blood spot samples

2021 ◽  
Vol 20 (1) ◽  
Author(s):  
Noam B. Teyssier ◽  
Anna Chen ◽  
Elias M. Duarte ◽  
Rene Sit ◽  
Bryan Greenhouse ◽  
...  
Keyword(s):  
Whole Genome Sequencing ◽  
Genome Sequencing ◽  
Dropout Rate ◽  
Dried Blood Spots ◽  
High Ratio ◽  
Low Density ◽  
Whole Genome ◽  
Cross Sectional ◽  
Modest Improvement ◽  
Primer Sets

Abstract Background Whole-genome sequencing (WGS) is becoming increasingly useful to study the biology, epidemiology, and ecology of malaria parasites. Despite ease of sampling, DNA extracted from dried blood spots (DBS) has a high ratio of human DNA compared to parasite DNA, which poses a challenge for downstream genetic analyses. The effects of multiple methods for DNA extraction, digestion of methylated DNA, and amplification were evaluated on the quality and fidelity of WGS data recovered from DBS. Methods Low parasite density mock DBS samples were created, extracted either with Tween-Chelex or QIAamp, treated with or without McrBC, and amplified with one of three different amplification techniques (two sWGA primer sets and one rWGA). Extraction conditions were evaluated on performance of sequencing depth, percentiles of coverage, and expected SNP concordance. Results At 100 parasites/μL, Chelex-Tween-McrBC samples had higher coverage (5 × depth = 93% genome) than QIAamp extracted samples (5 × depth = 76% genome). The two evaluated sWGA primer sets showed minor differences in overall genome coverage and SNP concordance, with a newly proposed combination of 20 primers showing a modest improvement in coverage over those previously published. Conclusions Overall, Tween-Chelex extracted samples that were treated with McrBC digestion and are amplified using 6A10AD sWGA conditions had minimal dropout rate, higher percentages of coverage at higher depth, and more accurate SNP concordance than QiaAMP extracted samples. These findings extend the results of previously reported methods, making whole genome sequencing accessible to a larger number of low density samples that are commonly encountered in cross-sectional surveys.

Asymptomatic low-density Plasmodium infection during non-transmission season: a community-based cross-sectional study in two districts of North Eastern Region, India

2021 ◽  
Author(s):  
Hari Shankar ◽  
Sobhan Phookan ◽  
Mrigendra Pal Singh ◽  
Ram Suresh Bharti ◽  
Naseem Ahmed ◽  
...  
Keyword(s):  
Cross Sectional Study ◽  
Diagnostic Tools ◽  
Eastern Region ◽  
Low Density ◽  
Plasmodium Infection ◽  
Sectional Study ◽  
Cross Sectional ◽  
Health Agencies ◽  
North Eastern ◽  
Asymptomatic Infections

Abstract Background Malaria elimination requires targeting asymptomatic and low-density Plasmodium infections that largely remain undetected. Therefore we conducted a cross-sectional study to estimate the burden of asymptomatic and low-density Plasmodium infection using conventional and molecular diagnostics. Methods A total of 9118 participants, irrespective of age and sex, were screened for malaria using rapid diagnostic tests (RDTs), microscopy and polymerase chain reaction. Results Among the participants, 707 presented with symptoms and 8411 without symptoms, of which Plasmodium was present in 15.6% (110/707) and 8.1% (681/8411), respectively. Low-density infection was found in 5.1% (145/2818) of participants and 8327 of 9118 were Plasmodium negative. Endemicity was propotional to asymptomatic infections (high endemicity 11.1% [404/3633] vs low endemicity 5.8% [277/4778]; odds ratio [OR] 2.0 [95% confidence interval {CI} 1.7 to 2.4]) but inversely related to low-density infection (high endemicity 3.7% [57/1545] vs low endemicity 6.9% [88/1273]; OR 1.9 [95% CI 1.4 to 2.7]). The spleen rate in children 2–9 y of age was 17.9% (602/3368) and the enlarged spleen index was 1.6. Children between 8 and 14 y showed higher odds for asymptomatic (adjusted OR [aOR] 1.75 [95% CI 1.4 to 2.2]) and low-density infections (aOR 0.63 [95% CI 0.4 to 1.0)] than adults. Conclusions The prevalence of asymptomatic and low-density Plasmodium infection undermines the usefulness of standard diagnostic tools used by health agencies. This necessitates deploying molecular tools in areas where malaria microscopy/RDTs indicate a dearth of infection.

scholarly journals Experimental Investigation on the Influence of Fiber Path Curvature on the Mechanical Properties of Composites

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2602
Author(s):  
Huaqiao Wang ◽  
Jihong Chen ◽  
Zhichao Fan ◽  
Jun Xiao ◽  
Xianfeng Wang
Keyword(s):  
Tensile Strength ◽  
Path Planning ◽  
Composite Laminates ◽  
Bending Strength ◽  
High Strength ◽  
Bending Test ◽  
Fiber Placement ◽  
Automated Fiber Placement ◽  
Fiber Path ◽  
Path Curvature

Automated fiber placement (AFP) has been widely used as an advanced manufacturing technology for large and complex composite parts and the trajectory planning of the laying path is the primary task of AFP technology. Proposed in this paper is an experimental study on the effect of several different path planning placements on the mechanical behavior of laminated materials. The prepreg selected for the experiment was high-strength toughened epoxy resin T300 carbon fiber prepreg UH3033-150. The composite laminates with variable angles were prepared by an eight-tow seven-axis linkage laying machine. After the curing process, the composite laminates were conducted by tensile and bending test separately. The test results show that there exists an optimal planning path among these for which the tensile strength of the laminated specimens decreases slightly by only 3.889%, while the bending strength increases greatly by 16.68%. It can be found that for the specific planning path placement, the bending strength of the composite laminates is significantly improved regardless of the little difference in tensile strength, which shows the importance of path planning and this may be used as a guideline for future AFP process.

scholarly journals Instability analysis of a filament-wound composite tube subjected to compression/bending

2019 ◽  
Vol 28 ◽  
pp. 096369351987741
Author(s):  
Gyula Szabó ◽  
Károly Váradi
Keyword(s):  
Failure Modes ◽  
Slenderness Ratio ◽  
Equivalent Stress ◽  
Bending Test ◽  
Test Machine ◽  
Fe Model ◽  
Rubber Tube ◽  
Nonlinear Buckling ◽  
Cross Sectional ◽  
Composite Tube

The aim of this study is to investigate the global buckling of a relatively long composite cord–rubber tube subjected to axial compression and its cross-sectional instability due to bending by a macromechanical nonlinear finite element (FE) model (nonlinear buckling analysis). Composite reinforcement layers are modelled as transversely isotropic ones, while elastomer liners are described by a hyperelastic material model that assumes incompressibility. Force–displacement, equivalent strain, equivalent stress results along with oblateness and curvature results for the complete process have been presented. It is justified that bending leads to ovalization of the cross section and results in a loss of the load-carrying capacity of the tube. Strain states in reinforcement layers have been presented, which imply that the probable failure modes of the reinforcement layers are both delamination and yarn-matrix debonding. There is a significant increase in strains due to cross-sectional instability, which proves that the effect of cross-sectional instability on material behaviour of the tube is crucial. A parametric analysis has been performed to investigate the effect of the member slenderness ratio on cross-sectional instability of the composite tube. It shows that Brazier force is inversely proportional to the slenderness ratio. It further shows that higher oblateness parameters occur in case of a lower slenderness ratio and that cross-sectional instability takes place at a lower dimensionless displacement in case of a lower slenderness ratio. FE results have been validated by a compression/bending test experiment conducted on a tensile test machine.

200 and Counting: Unlocking CBM Potential with High-Strength, Low-Density Cement Slurry

2017 ◽  
Author(s):  
Dharmesh Talong ◽  
Animesh Kumar ◽  
Arindam Sarma ◽  
Kuhu Priyamvada ◽  
Vaibhav Tyagi ◽  
...  
Keyword(s):  
High Strength ◽  
Low Density ◽  
Cement Slurry
Sign in / Sign up

Export Citation Format

Share Document