scholarly journals A Dual-Band Multiple Input Multiple Output Frequency Agile Antenna for GPSL1/Wi-Fi/WLAN2400/LTE Applications

2016 ◽  
Vol 2016 ◽  
pp. 1-11 ◽  
Author(s):  
Sajid Aqeel ◽  
M. H. Jamaluddin ◽  
Aftab Ahmad Khan ◽  
Rizwan Khan ◽  
M. R. Kamarudin ◽  
...  
Keyword(s):  
Dielectric Resonator ◽  
Frequency Tuning ◽  
Ground Plane ◽  
Multiple Input Multiple Output ◽  
Dual Band ◽  
Impedance Bandwidth ◽  
Single Element ◽  
Lower Band ◽  
Multiple Input ◽  
Input Multiple Output

A novel dual-band, single element multiple input multiple output (MIMO) dielectric resonator antenna (DRA) with a modest frequency tuning ability is presented in this communication. The proposed antenna operates at GPS L1/Bluetooth/Wi-Fi/LTE2500/WLAN2400 frequency bands. A single dielectric resonator element is fed by two coaxial probes to excite the orthogonal modes. A couple of slots are introduced on the ground plane to improve the isolation between antenna ports. The slots also serve the purpose of reconfiguration in the lower band on placement of switches at optimized locations. The measured impedance bandwidth is 5.16% (1.41–1.49 GHz) in the lower band and 26% (2.2–2.85 GHz) in the higher band. The lower band reconfigures with an impedance bandwidth of 6.5% (1.55–1.65 GHz) when PIN diodes are switched ON. The gain, efficiency, correlation coefficient, and diversity gain of the MIMO DRA are presented with a close agreement between simulated and measured results.

A DUAL BAND MIMO DIELECTRIC RESONATOR ANTENNA FOR WLAN APPLICATION

2015 ◽  
Vol 77 (10) ◽  
Author(s):  
Nuramirah Mohd Nor ◽  
Mohd Haizal Jamaluddin
Keyword(s):  
Dielectric Resonator ◽  
Wireless Local Area Network ◽  
Local Area Network ◽  
Multiple Input Multiple Output ◽  
Dual Band ◽  
Impedance Bandwidth ◽  
Area Network ◽  
Dielectric Resonator Antenna ◽  
Multiple Input ◽  
Input Multiple Output

In this paper, a dual band multiple-input-multiple-output dielectric resonator antenna for wireless local area network application is presented. Two identical feeding techniques are used to feed the proposed antenna. The simulated impedance bandwidth for both port are the same which are 6.5% at 2.45 GHz and 3% at 5.2 GHz. The DRA also has an acceptable value of isolation over the operating frequency. The simulated S-parameter and other multiple-input-multiple-output parameters are studied and observed.

scholarly journals A MIMO H-shape Dielectric Resonator Antenna for 4G Applications

2018 ◽  
Vol 10 (2) ◽  
pp. 648
Author(s):  
S. Salihah ◽  
M. H. Jamaluddin ◽  
R. Selvaraju ◽  
M. N. Hafiz
Keyword(s):  
Electrical Properties ◽  
Dielectric Resonator ◽  
Return Loss ◽  
Multiple Input Multiple Output ◽  
Impedance Bandwidth ◽  
Dielectric Resonator Antenna ◽  
Multiple Input ◽  
Input Multiple Output ◽  
Good Potential ◽  
Slot Coupling

In this article, a Multiple-Input-Multiple-Output (MIMO) H-shape Dielectric Resonator Antenna (DRA) is designed and simulated at 2.6 GHz for 4G applications. The proposed structure consists of H-shape DRA ( =10) which is mounted on FR4 substrate ( =4.6), and feed by two different feeding mechanisms. First, microstrip with slot coupling as Port 1. Second, coaxial probe as Port 2. The electrical properties of the proposed MIMO H-shape DRA in term of return loss, bandwidth and gain are completely obtained by using CST Microwave Studio Suite Software. The simulated results demonstrated a return loss more than 20 dB, an impedance bandwidth of 26 % (2.2 – 2.9 GHz), and gain of 6.11 dBi at Port 1. Then, a return loss more than 20 dB, an impedance bandwidth of 13 % (2.2 – 2.7 GHz), and gain of 6.63 dBi at Port 2. Both ports indicated impedance bandwidth more than 10 %, return loss lower than 20 dB, and gain more than 10 dBi at 2.6 GHz. The simulated electrical properties of the proposed design show a good potential for LTE applications.

A Superwideband Monopole Multiple-Input-Multiple-Output (MIMO) Antenna with Dual Notched (Inverted T-Shaped Stub/U-Shaped Slit) Band Characteristics for Wireless Applications

2019 ◽  
Vol 16 (10) ◽  
pp. 4242-4248
Author(s):  
Manoj Kapil ◽  
Manish Sharma
Keyword(s):  
Ground Plane ◽  
Multiple Input Multiple Output ◽  
Impedance Bandwidth ◽  
Mimo Antenna ◽  
Wireless Applications ◽  
Research Article ◽  
Compact Size ◽  
Multiple Input ◽  
Input Multiple Output ◽  
Microstrip Feed

In this research article, a compact MIMO (Multiple-Input-Multiple-Output) antenna with inclusion of two notched bands characteristics is presented. Designed MIMO antenna consist of dual radiating patches printed on one surface of the substrate which covers measured wide impedance bandwidth of 2.88 GHz–19.98 GHz and satisfies bandwidth ratio more than 10:1 for superwideband with compact size of 18 mm × 34 mm. Two radiating patch are placed symmetrically for MIMO configuration and notched bands to eliminate WiMAX/C and WLAN bands are obtained by attaching inverted T-shaped stub on radiating patch and etched inverted U-shape slit in microstrip feed. Isolation between the two radiating patch is maintained by adding two L-shaped stub in slotted rectangular ground plane. Measured radiation pattern are stable in operating band and offers maximum 4.23 dBi and 89% gain and radiation efficiency respectively. Moreover, antenna shows good diversity performance with Envelope-Correlation-Coefficient (ECC) < 0.5, Directive-Gain (DG) > 9.95 dB and Total-Active-Reflection Coefficient (TARC) < -30 dB.

Dual-band-notched antenna for UWB MIMO applications

2015 ◽  
Vol 9 (2) ◽  
pp. 381-386 ◽  
Author(s):  
Zamir Wani ◽  
Dinesh Kumar
Keyword(s):  
Ground Plane ◽  
Multiple Input Multiple Output ◽  
Split Ring Resonator ◽  
Antenna System ◽  
Ultra Wideband ◽  
Dual Band ◽  
Compact Antenna ◽  
Complementary Split Ring Resonator ◽  
Multiple Input ◽  
Input Multiple Output

In this report, a compact antenna system with dual-band-notched characteristics is proposed for ultra-wideband (UWB) multiple-input multiple-output (MIMO) applications. Two antenna elements are placed side by side and fed with matched microstrip lines on a substrate with an area of 35 × 30 mm2. Notched characteristics at WiMAX (3.4–3.6 GHz) and WLAN (5.725–5.825 GHz) have been achieved using complementary split ring resonator (SRR) slots etched in both the antenna elements. Electromagnetic isolation between the two elements close to each other is achieved using a ground T-stub and slots etched in the ground plane. Antenna system has been tested and measured results are close to the desired ones. Measured isolation >20 dB is obtained in most of the UWB bands. The proposed antenna system meets the requirements well for MIMO applications.

scholarly journals Design of Quad-Port Ultra-Wideband Multiple-Input-Multiple-Output Antenna with Wide Axial-Ratio Bandwidth

Sensors ◽  
2020 ◽  
Vol 20 (4) ◽  
pp. 1174 ◽  
Author(s):  
Pawan Kumar ◽  
Shabana Urooj ◽  
Areej Malibari
Keyword(s):  
Ground Plane ◽  
Multiple Input Multiple Output ◽  
Axial Ratio ◽  
Dielectric Substrate ◽  
Ultra Wideband ◽  
Impedance Bandwidth ◽  
Mimo Antenna ◽  
Multiple Input ◽  
Input Multiple Output ◽  
Good Agreement

This article presents a compact, planar, quad-port ultra-wideband (UWB) multiple-input–multiple-output (MIMO) antenna with wide axial ratio bandwidth (ARBW). The proposed MIMO design consists of four identical square-shaped antenna elements, where each element is made up of a circular slotted ground plane and feed by a 50 Ω microstrip line. The circular polarization is achieved using a protruding hexagonal stub from the ground plane. The four elements of the MIMO antenna are placed orthogonally to each other to obtain high inter-element isolation. FR-4 dielectric substrate of size 45 × 45 × 1.6 mm3 is used for the antenna prototype, and a good agreement is noticed among the simulated and experimental results. The proposed MIMO antenna shows 3-dB ARBW of 52% (3.8–6.5 GHz) and impedance bandwidth (S11 ≤ −10 dB) of 144% (2.2–13.5 GHz).

scholarly journals A Compact Dual-Band CPW-Fed MIMO Antenna for Indoor Applications

2019 ◽  
Vol 2019 ◽  
pp. 1-7
Author(s):  
Mohamed M. Morsy
Keyword(s):  
Coupling Effect ◽  
Impedance Matching ◽  
Ground Plane ◽  
Multiple Input Multiple Output ◽  
Surface Current ◽  
Dual Band ◽  
Single Element ◽  
Mimo Antenna ◽  
Input Multiple Output ◽  
Parametric Studies

A compact dual-band multiple-input-multiple-output (MIMO) antenna for LTE700, GSM1900, and UMTS applications with high isolation is presented. To enhance impedance matching and multiband operation, two inverted L-shaped monopoles are printed in the circular slot of the ground plane. The single element design is mirrored along the diameter of the circular slot of the ground plane. A strip is employed between the two radiators in order to mitigate the mutual coupling effect and enhance the impedance matching at operating bandwidths. Moreover, two slits are inserted in the ground plane in order to disturb the current distribution between radiating elements, and hence, the isolation between elements is improved. The measured 10 dB return loss bandwidth is 100 MHz (698–798 MHz) and 359 MHz (1765-2124 MHz) over the LTE700, GSM1900, and UMTS bands. The measured isolation between the two ports is less than -13 dB over the LTE700 bands while it is recorded to be less than -17 dB over the GSM1900 and UMTS bands. In addition, parametric studies of the proposed MIMO antenna are performed, and the surface current analysis is discussed to show the effect of the isolation structure. The radiation patterns are measured, and envelope correlation coefficient is calculated. The simulated results are in good agreement with measurements.

A compact dual-polarized co-radiator MIMO antenna for UWB applications

2021 ◽  
pp. 1-14
Author(s):  
Harleen Kaur ◽  
Hari Shankar Singh ◽  
Rahul Upadhyay
Keyword(s):  
Ground Plane ◽  
Multiple Input Multiple Output ◽  
Ultra Wideband ◽  
Impedance Bandwidth ◽  
Mimo Antenna ◽  
Wireless Applications ◽  
Multiple Input ◽  
Input Multiple Output ◽  
Dual Polarized ◽  
Uwb Applications

Abstract In this research study, a compact dual-polarized co-radiator ultra-wideband (UWB) multiple-input multiple-output (MIMO) antenna with improved impedance bandwidth and isolation is proposed for wireless applications. The designed co-radiator has an overall area of 0.3λo × 0.3λo mm2 (where, λo is free space wavelength corresponding to the lower cut-off frequency, i.e., 3.1 GHz). The proposed resonator comprises of a hybrid geometry which is created with the combinations of a circular-shaped patch, a square, and two rectangular stubs. It is centrally aligned between two 50 Ω micro-strip feed lines that are positioned orthogonal to each other. Further, the modified ground plane is attached with the end-loaded line which provides broadband isolation over entire UWB frequency band. The simulated results of the proposed antenna exhibit wideband characteristics with impedance bandwidth of 3.1–16.9 GHz with minimum isolation of −15 dB. Moreover, all the radiation performance parameters are analyzed and discussed. Some important diversity parameters such as envelope correlation coefficient, mean effective gain, effective diversity gain, and channel capacity loss have also been evaluated. Furthermore, all the measured results of proposed antenna agree well with the simulated results which make the proposed antenna a suitable candidate for UWB-MIMO wireless applications.

scholarly journals Circularly Polarized Wideband Fabric Stealth Multiple-Input Multiple-Output Antenna for Ultrawideband Applications Useful for Wireless Systems Wearable on Garments

2021 ◽  
Vol 2021 ◽  
pp. 1-16
Author(s):  
Pillalamarri Laxman ◽  
Anuj Jain
Keyword(s):  
Human Body ◽  
Ground Plane ◽  
Multiple Input Multiple Output ◽  
Impedance Bandwidth ◽  
Antenna Element ◽  
Wireless Devices ◽  
Circularly Polarized ◽  
Mimo Antenna ◽  
Multiple Input ◽  
Input Multiple Output

Stealth wearable wireless devices are gaining much attention in the personal security and fashion designing industry. A multiple-input multiple-output wideband circularly polarized antenna wearable on a dress (textile-related), which is immune to bending, is described in this paper, where a wearable on fabric dress application uses the MIMO techniques. It consists of two multiple-input multiple-output types of antenna elements: the resonating elements are created resembling a beautiful peacock shape and the ground plane is appropriately designed. A voltage is applied to each antenna element; the ground plane contains a microstrip transmission line-fed and a rectangular upside-down L-shaped (vertically flipped) strip used for circular polarizing. The antenna covers a 3 dB axial-ratio-band-width (ARBW) value of 5.20–7.10 GHz and impedance bandwidth (S11 less than −10 dB) of 03.60–13.0 GHz. The proposed attachable wearable fabric (textile) multiple-input multiple-output wideband antenna exhibits envelope correlation coefficient (ECC) <0.02, diversity gain (DG) >9.96, channel capacity loss (CCL) <0.2 b/s/Hz, total active reflective coefficient (TARC) <−10 dB, mean effective gain (MEG) ratio within ±0.5 dB. There is dual-sense circular polarization in this antenna and high isolation between resonating elements (higher than 18). A specific absorption rate (SAR) of the proposed antenna for human tissues specimen is also discussed for different situations related to the human body. The overall size of the proposed CP textile MIMO antenna is 34 : 5 × 42 × 1 mm3. Because of its clothing layers (textile), practical performance, and miniature size, the designed MIMO antenna may be helpful for wearable on cloths on human body wireless devices and systems. The proposed antenna can be made unrecognizable because of the beautiful peacock design that can easily mix with the designs of fabric (in the fashion dress). The simulated antenna was fabricated with the help of conventional manual fabrication techniques and tested in real-time situations. The edge-to-edge distance amid the MIMO radiating antennas is 14.2 mm, and the achieved isolation is greater than 18 dB after optimization of the proposed antenna.

Sign in / Sign up

Export Citation Format

Share Document