scholarly journals Flow Characteristics Study of Wind Turbine Blade with Vortex Generators

2016 ◽  
Vol 2016 ◽  
pp. 1-11 ◽  
Author(s):  
Hao Hu ◽  
Xin-kai Li ◽  
Bo Gu
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Horizontal Axis ◽  
Vortex Generators ◽  
Propeller Shaft ◽  
Horizontal Axis Wind Turbine ◽  
Separation Line ◽  
Blade Root ◽  
Pneumatic Power ◽  
Large Wind

The blade root flow control is of particular importance to the aerodynamic characteristic of large wind turbines. The paper studies the feasibility of improving blade pneumatic power by applying vortex generators (VGs) to large variable propeller shaft horizontal axis wind turbines, with 2 MW variable propeller shaft horizontal axis wind turbine blades as research object. In the paper, three cases of VGs installation are designed; they are scattered in different chordwise position at the blade root, and then they are calculated, respectively, with CFD method. The results show that VGs installed in the separation line upstream, with the separation line of the blade root as a benchmark, show a better effect. Pneumatic power of blades increases by 0.6% by installing VGs. Although the effect on large wind turbines is not obvious, there is a space for optimization.

scholarly journals Modeling and simulation of forces applied to the horizontal axis wind turbine rotors by the vortex method coupled with the method of the blade element

2021 ◽  
Vol 12 (1) ◽  
pp. 413
Author(s):  
Ibtissem Barkat ◽  
Abdelouahab Benretem ◽  
Fawaz Massouh ◽  
Issam Meghlaoui ◽  
Ahlem Chebel
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Wind Farms ◽  
Vortex Method ◽  
Operating Conditions ◽  
Horizontal Axis ◽  
Rotor Blades ◽  
Good Representation ◽  
Horizontal Axis Wind Turbine ◽  
Blade Element

This article aims to study the forces applied to the rotors of horizontal axis wind turbines. The aerodynamics of a turbine are controlled by the flow around the rotor, or estimate of air charges on the rotor blades under various operating conditions and their relation to the structural dynamics of the rotor are critical for design. One of the major challenges in wind turbine aerodynamics is to predict the forces on the blade as various methods, including blade element moment theory (BEM), the approach that is naturally adapted to the simulation of the aerodynamics of wind turbines and the dynamic and models (CFD) that describes with fidelity the flow around the rotor. In our article we proposed a modeling method and a simulation of the forces applied to the horizontal axis wind rotors turbines using the application of the blade elements method to model the rotor and the vortex method of free wake modeling in order to develop a rotor model, which can be used to study wind farms. This model is intended to speed up the calculation, guaranteeing a good representation of the aerodynamic loads exerted by the wind.

Measurement of Unsteady Aerodynamics Load on the Blade of Field Horizontal Axis Wind Turbine

2007 ◽  
Author(s):  
Takao Maeda ◽  
Yasunari Kamada ◽  
Keita Naito ◽  
Yuu Ouchi ◽  
Masayoshi Kozawa
Keyword(s):  
Wind Turbine ◽  
Pressure Distribution ◽  
Mode Frequency ◽  
Horizontal Axis ◽  
Strain Gauges ◽  
Aerodynamic Forces ◽  
Horizontal Axis Wind Turbine ◽  
Blade Root ◽  
Blade Section ◽  
Mechanical Moment

This paper describes an experimental field study of the rotor aerodynamics of wind turbines. The test wind turbine is a horizontal axis wind turbine, or: HAWT with a diameter of 10m. The pressure distributions on the rotating blade are measured with multi point pressure transducers. Sectional aerodynamic forces are analyzed from pressure distribution. Blade root moments are measured simultaneously by a pair of strain gauges. The inflow wind is measured by a three component sonic anemometer, the local inflow of the blade section are measured by a pair of 7 hole Pitot tubes. The relation between the aerodynamic moments on the blade root from pressure distribution and the mechanical moment from strain gauges is discussed. The aerodynamic moments are estimated from the sectional aerodynamic forces and show oscillation caused by local wind speed and direction change. The mechanical moment shows similar oscillation to the aerodynamic excepting the short period oscillation of the blade first mode frequency. The fluctuation of the sectional aerodynamic force triggers resonant blade oscillations. Where stall is present along the blade section, the blade’s first mode frequency is dominant. Without stall, the rotating frequency is dominant in the blade root moment.

scholarly journals Comparison of horizontal axis wind turbine (HAWT) and vertical axis wind turbine (VAWT)

2018 ◽  
Vol 7 (4.13) ◽  
pp. 74 ◽  
Author(s):  
Muhd Khudri Johari ◽  
Muhammad Azim A Jalil ◽  
Mohammad Faizal Mohd Shariff
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Vertical Axis ◽  
Green Technology ◽  
Horizontal Axis ◽  
Vertical Axis Wind Turbine ◽  
Horizontal Axis Wind Turbine ◽  
Current Output ◽  
Voltage Output ◽  
And Performance

As the demand for green technology is rising rapidly worldwide, it is important that Malaysian researchers take advantage of Malaysia’s windy climates and areas to initiate more power generation projects using wind. The main objectives of this study are to build a functional wind turbine and to compare the performance of two types of design for wind turbine under different speeds and behaviours of the wind. A three-blade horizontal axis wind turbine (HAWT) and a Darrieus-type vertical axis wind turbine (VAWT) have been designed with CATIA software and constructed using a 3D-printing method. Both wind turbines have undergone series of tests before the voltage and current output from the wind turbines are collected. The result of the test is used to compare the performance of both wind turbines that will imply which design has the best efficiency and performance for Malaysia’s tropical climate. While HAWT can generate higher voltage (up to 8.99 V at one point), it decreases back to 0 V when the wind angle changes. VAWT, however, can generate lower voltage (1.4 V) but changes in the wind angle does not affect its voltage output at all. The analysis has proven that VAWT is significantly more efficient to be built and utilized for Malaysia’s tropical and windy climates. This is also an initiative project to gauge the possibility of building wind turbines, which could be built on the extensive and windy areas surrounding Malaysian airports.  

scholarly journals Parametric Analysis Using CFD to Study the Impact of Geometric and Numerical Modeling on the Performance of a Small Scale Horizontal Axis Wind Turbine

Energies ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 505
Author(s):  
Muhammad Salman Siddiqui ◽  
Muhammad Hamza Khalid ◽  
Abdul Waheed Badar ◽  
Muhammed Saeed ◽  
Taimoor Asim
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Reference Frames ◽  
Horizontal Axis ◽  
Small Scale ◽  
High Fidelity ◽  
Horizontal Axis Wind Turbine ◽  
Rapid Variability ◽  
The Impact ◽  
Numerical Complexity

The reliance on Computational Fluid Dynamics (CFD) simulations has drastically increased over time to evaluate the aerodynamic performance of small-scale wind turbines. With the rapid variability in customer demand, industrial requirements, economic constraints, and time limitations associated with the design and development of small-scale wind turbines, the trade-off between computational resources and the simulation’s numerical accuracy may vary significantly. In the context of wind turbine design and analysis, high fidelity simulation under full geometric and numerical complexity is more accurate but pose significant demands from a computational standpoint. There is a need to understand and quantify performance deterioration of high fidelity simulations under reduced geometric or numerical approximation on a single small scale turbine model. In the present work, the flow past a small-scale Horizontal Axis Wind Turbine (HAWT) was simulated under various geometric and numerical configurations. The geometric complexity was varied based on stationary and rotating turbine conditions. In the stationary case, simple 2D airfoil, 2.5D blade, 3D blade sections are evaluated, while rotational effects are introduced for the configuration 3D blade, rotor only, and the full-scale wind turbine with and without the inclusion of a nacelle and tower. In terms of numerical complexity, the Single Reference Frame (SRF), Multiple Reference Frames (MRF), and the Sliding Meshing Interface (SMI) is analyzed over Tip Speed Ratios (TSR) of 3, 6, 10. The quantification of aerodynamic coefficients of the blade (Cl, Cd) and turbine (Cp, Ct) was conducted along with the discussion on wake patterns in comparison with experimental data.

424 Clarification of Boundary Layer around Blade Root of Horizontal Axis Wind Turbine

2013 ◽  
Vol 2013.62 (0) ◽  
pp. 253-254
Author(s):  
Yosuke KAGISAKI ◽  
Yasunari KAMADA ◽  
Takao MAEDA ◽  
Junsuke MURATA ◽  
Daiki SUZUKI
Keyword(s):  
Boundary Layer ◽  
Wind Turbine ◽  
Horizontal Axis ◽  
Horizontal Axis Wind Turbine ◽  
Blade Root

Analysis on Aerodynamic Performance of Horizontal Axis Wind Turbine Based on Nonlinear Wake Model

2013 ◽  
Vol 448-453 ◽  
pp. 1716-1720
Author(s):  
Rui Yang ◽  
Jiu Xin Wang ◽  
Sheng Long Zhang
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Optimization Design ◽  
Aerodynamic Performance ◽  
Horizontal Axis ◽  
Wake Vortex ◽  
Horizontal Axis Wind Turbine ◽  
Horizontal Axis Wind Turbines ◽  
Wake Model ◽  
Induced Velocity

A computational method based on nonlinear wake model was established for horizontal axis wind turbines aerodynamic performance prediction. This method makes use of finite difference method to solve the integral differential equation of the model, the induced velocity of wake vortex can be calculated from equations and compared with the induced velocity of wake vortex in linear model. The comparison between the calculated results of wind turbine under axis flow condition, including tip vortex geometry and aerodynamic performance, and available experimental data shows that this method is suitable for wind turbine aerodynamic performance analysis. Finally, a series of numerical calculations were made to investigate the change of wake geometry and aerodynamic performance of the wind turbine when yawing and pitch angle increasing, which provide foundations for aerodynamic optimization design of horizontal axis wind turbines.

scholarly journals Observation of the Starting and Low Speed Behavior of Small Horizontal Axis Wind Turbine

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Sikandar Khan ◽  
Kamran Shah ◽  
Izhar-Ul-Haq ◽  
Hamid Khan ◽  
Sajid Ali ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Horizontal Axis ◽  
Horizontal Axis Wind Turbine ◽  
Wind Speeds ◽  
Starting Time ◽  
Speed Range ◽  
Horizontal Axis Wind Turbines ◽  
Starting Torque ◽  
High Angles Of Attack

This paper describes the starting behavior of small horizontal axis wind turbines at high angles of attack and low Reynolds number. The unfavorable relative wind direction during the starting time leads to low starting torque and more idling time. Wind turbine models of sizes less than 5 meters were simulated at wind speed range of 2 m/s to 5 m/s. Wind turbines were modeled in Pro/E and based on the optimized designs given by MATLAB codes. Wind turbine models were simulated in ADAMS for improving the starting behavior. The models with high starting torques and less idling times were selected. The starting behavior was successfully improved and the optimized wind turbine models were able to produce more starting torque even at wind speeds less than 5 m/s.

METHODS OF QUALITATIVE ANALYSIS IN THE PROBLEM OF RIGID BODY MOTION IN MEDIUM

2011 ◽  
Vol 21 (10) ◽  
pp. 2955-2961 ◽  
Author(s):  
VITALY A. SAMSONOV ◽  
MARAT Z. DOSAEV ◽  
YURY D. SELYUTSKIY
Keyword(s):  
Qualitative Analysis ◽  
Rigid Body ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Classical Problem ◽  
Rigid Body Motion ◽  
Horizontal Axis ◽  
Body Motion ◽  
Horizontal Axis Wind Turbine ◽  
And Behavior

The present paper describes the application of methods of qualitative analysis in the classical problem of rigid body motion in medium. Three particular problems are used as examples: bolides flight, galloping of aeroelastic constructions, and behavior of horizontal axis wind turbine. It is shown that this approach reveals the general properties of the behavior of objects studied, such as impossibility of translational deceleration of bolides and the presence of hysteretic phenomena in the operation of wind turbines.

Sign in / Sign up

Export Citation Format

Share Document