scholarly journals Use of Oxalic-Acid-Modified Stellerite for Improving the Filter Capability of PM2.5 of Paper Composed of Bamboo Residues

2016 ◽  
Vol 2016 ◽  
pp. 1-7
Author(s):  
Hua Chen ◽  
Jian Lou ◽  
Fei Yang ◽  
Jia-nan Zhou ◽  
Yan Zhang ◽  
...  
Keyword(s):  
Oxalic Acid ◽  
Pore Formation ◽  
Strength Properties ◽  
Filtration Efficiency ◽  
Kraft Pulping ◽  
Paper Strength ◽  
Cationic Starch ◽  
Promising Technique ◽  
Cooking Temperature ◽  
Experimental Parameters

In this study, pulping conditions for kraft pulping of bamboo residues were investigated, predominantly focusing on cooking temperature and time during pulping. Oxalic acid and cationic starch were used for the modification of natural stellerite, and the use of modified stellerite for preparing filter paper for PM2.5 filtration was investigated. The optimal pulping technology of bamboo residues was established based on the following experimental parameters: liquor ratio of 1 : 5.5, cooking temperature of 160°C, and a holding time of 2 h. Modification by oxalic acid resulted in the promotion of pore formation at the stellerite surfaces and induced the microscopic changes. Nevertheless, paper strength remained practically unchanged after the addition of fillers, indicating that the cationic starch preblend method is a promising technique for papermaking because it enhances the strength properties of paper. With the variation in the addition of modified stellerite from 3 to 15%, while simultaneously maintaining the basis weight constant at 60 gm−2, the filtration efficiency of paper sheets first increased and then decreased later; thus the optimum stellerite content was found to be 9%. Filtration efficiency was suggested to be affected by gas flowing velocity.

A novel predictive method for filler coflocculation with cellulose microfibrils

TAPPI Journal ◽  
2019 ◽  
Vol 18 (11) ◽  
pp. 653-664
Author(s):  
IGNACIO DE SAN PIO ◽  
KLAS G. JOHANSSON ◽  
PAUL KROCHAK
Keyword(s):  
Negative Impact ◽  
High Strength ◽  
Strength Properties ◽  
Cellulose Microfibrils ◽  
Paper Strength ◽  
Flow Loop ◽  
Cationic Starch ◽  
Reflectance Measurement ◽  
Drainage Rate ◽  
Complete Study

Different strategies aimed at reducing the negative impact of fillers on paper strength have been the objective of many studies during the past few decades. Some new strategies have even been patented or commercialized, yet a complete study on the behavior of the filler flocs and their effect on retention, drainage, and formation has not been found in literature. This type of research on fillers is often limited by difficulties in simulating high levels of shear at laboratory scale similar to those at mill scale. To address this challenge, a combination of techniques was used to compare preflocculation (i.e., filler is flocculated before addition to the pulp) with coflocculation strategies (i.e., filler is mixed with a binder and flocculated before addition to the pulp). The effect on filler and fiber flocs size was studied in a pilot flow loop using focal beam reflectance measurement (FBRM) and image analysis. Flocs obtained with cationic polyacrylamide (CPAM) and bentonite were shown to have similar shear resistance with both strategies, whereas cationic starch (CS) was clearly more advantageous when coflocculation strategy was used. The effect of flocculation strategy on drainage rate, STFI formation, ash retention, and standard strength properties was measured. Coflocculation of filler with CPAM plus bentonite or CS showed promising results and produced sheets with high strength but had a negative impact on wire dewatering, opening a door for further optimization.

scholarly journals New Diatomite Filler for Improvement of Paper Strength Properties

2020 ◽  
Vol 71 (5) ◽  
pp. 479-490 ◽  
Author(s):  
Wei Shang ◽  
Haoran Han ◽  
Hunan Liang
Keyword(s):  
Particle Size ◽  
Strength Properties ◽  
Filler Loading ◽  
Sodium Hexametaphosphate ◽  
Paper Strength ◽  
Pulp Fibers ◽  
Cationic Starch ◽  
Coating Method ◽  
Filler Retention ◽  
Modified Diatomite

In this work, diatomite particles were modified to improve the bondability of diatomite particles with pulp fibers and filler retention via a complex of cationic starch-sodium hexametaphosphate coating method. The particle size, FTIR spectroscopy characteristic and morphology of the resulting modified diatomite were studied to confirm the successful modification. The SEM results illustrated that the surface of modified diatomite particles was covered by the complex coatings. The coating efficiency of the complex of cationic starch-sodium hexametaphosphate on diatomite surface was up to 98%. Compared with the handsheet filled unmodified diatomite, the handsheet filled with modified diatomite had higher strength properties and lower bulk. When cationic starch dosage was 7%, and filler dosage was 25% , the resulting tensile strength of filled modified diatomite handsheet was 22.1% higher than the handsheet filled unmodified diatomite. Furthermore, with the filler loading of 30%, compared with that of unmodified diatomite, filler retention of modified diatomite was increased by 20.4%. The larger particle size and higher zeta potential of modified diatomite were benefitial to increase retention of modified diatomite filler.

Cationic emulsions of maleic anhydride derivatives of oleic acid and abietic acid for hydrophobic sizing of paper

TAPPI Journal ◽  
2020 ◽  
Vol 19 (6) ◽  
pp. 281-290
Author(s):  
MARTIN A. HUBBE ◽  
LOKENDRA PAL ◽  
AHSEN EZEL BILDIK DAL
Keyword(s):  
Oleic Acid ◽  
Abietic Acid ◽  
Secondary Ion Mass Spectrometry ◽  
Kraft Pulping ◽  
Resin Acids ◽  
Paper Strength ◽  
Cationic Starch ◽  
Tensile Index ◽  
Index Value ◽  
Sizing Agents

Ordinary rosin sizing agents are mixtures of resin acids that include abietic acid and related com-pounds obtained from softwoods such as pine. Fatty acids, which are another byproduct of the kraft pulping of soft-wood species, also may have hydrophobic effects, but their use as sizing agents has seldom been considered. In the current study, abietic acid and oleic acid, in the absence of other components, were first modified by reaction with maleic acid anhydride. Then, the maleated derivatives (maleated oleic acid [MOA] and maleated abietic acid [MAA]), which were emulsified with cationic starch at the 1:1 and 3:2 ratio, respectively, were added to fiber furnish containing aluminum sulfate (papermaker’s alum). The prepared sheets were dried with a rotating drum on one side at 100°C at low pressure to cure the sizing agents. The chemical, optical strength, and absorption properties were measured. The presence of the sizing material was confirmed using time of flight secondary ion mass spectrometry (ToF-SIMS), and the retention of the sizing agent on fibers was supported by evidence of hydrocarbons on the paper surface. In addition to achieving sufficient water resistance features with MAA, a lesser hydrophobic character was obtained when using MOA. Compared to commercial applications, relatively large amounts of sizing agent were used to obtain a sufficient sizing degree. The MOA required 5% addition to achieve a similar sizing degree as MAA at the 2% level. The sizing treatments also resulted in substantial increases in tensile index value. Since cationic starch was used in the formulation of the sizing agents, the increase in tensile index may have been due to the influence of cationic starch. Contributions to paper strength from a combination of ionic complexation and mutual association of hydrophobic groups is also proposed. Depending on the amount of sizing agent, the yellowness increased, especial-ly when sizing with MOA.

scholarly journals Xylanase pretreatment of mechanically destructured chips of Eucalyptus tereticornis and its effect on kraft pulping

BioResources ◽  
2021 ◽  
Vol 16 (3) ◽  
pp. 5361-5375
Author(s):  
Laxman Kumar Pandey ◽  
Amit Kumar ◽  
Surendra Pal Singh ◽  
Dharm Dutt
Keyword(s):  
Treated Wood ◽  
Untreated Wood ◽  
Strength Properties ◽  
Kraft Pulping ◽  
Kappa Number ◽  
Wood Chips ◽  
Pulp Yield ◽  
Physical Strength ◽  
Cooking Temperature ◽  
Combined Pretreatment

Mechanical pulping of raw wood material is a highly energy intensive and pollution generating step in the papermaking process. This study focused on combined mechanical and xylanase treatment prior to the kraft pulping of E. tereticornis. A screened pulp yield of 49.1% (on oven-dry wood basis) with a Kappa number of 24.9 was obtained at the optimum cooking temperature of 160 °C without any pretreatment of the wood chips. After mechanical treatment (destructuring), a slightly higher screened pulp yield (49.4%) was obtained with a Kappa number of 24.2 at the cooking temperature of 145 °C with the same active alkali charge (15%). The optimum cooking temperature was further reduced to 140 °C for the destructured xylanase-treated wood chips. The xylanase treatment resulted in a 2% reduction in screened pulp yield due to hydrolysis of xylan. However, the Kappa number was reduced to 18.2 after xylanase pretreatment of the mechanically destructured wood chips. The combined pretreatment (destructured and xylanase treatment) of wood chips resulted in a reduction in cooking temperature by 20°C compared to untreated wood chips. Such a reduction in cooking temperature can effectively reduce steam consumption. The combined pretreatment improved the pulp brightness by 2.0 (ISO points) and physical strength properties, which included the tensile index, tear index, and burst index by 11.06%, 21.72%, and 21.79%, respectively, compared to the control.

Filler modified by a sequential encapsulation and preflocculation method and its effect on paper properties

2020 ◽  
Vol 35 (1) ◽  
pp. 89-95
Author(s):  
Nannan Chen ◽  
Lijun Wang ◽  
Junchao Wen ◽  
Xianping Yao ◽  
Wenyan Zhao
Keyword(s):  
Filler Content ◽  
Strength Properties ◽  
Paper Strength ◽  
Cationic Starch ◽  
Paper Properties ◽  
Polyelectrolyte Complexes ◽  
New Methods ◽  
Charge Potential ◽  
Filler Retention ◽  
Anionic Polyacrylamide

AbstractIncreasing the filler content of sheet tends to decrease filler retention and paper strength properties. To overcome this problem and make better use of fillers, development of new methods on filler modification has never been stopped. In this study, filler modification was carried out by sequentially adding an anionic polyacrylamide, a cationic starch and a cationic polyacrylamide. It is believed that in this process, multiple polyelectrolyte complexes are formed which can not only encapsulate filler particles but also preflocculate the particles. The results showed that, compared to the single preflocculation treatment, the sequential encapsulation and preflocculation (SEP) treatment brought significantly larger particle size and higher surface charge potential of the filler, thus higher filler retention was achieved. When the modified fillers were used for papermaking and paper ash contents were controlled at the same level, the SEP modification was better in improving the tensile index, internal bond strength and tearing index of paper than the single preflocculation method, in addition, it maintained better paper formation, caused insignificant change on opacity of paper. It is believed that this newly developed SEP method is worthy of being applied to industrial scales in making various grades of filled paper.

Co-cooking nonwoods with hardwoods

TAPPI Journal ◽  
2014 ◽  
Vol 13 (6) ◽  
pp. 19-24
Author(s):  
TROY RUNGE ◽  
CHUNHUI ZHANG
Keyword(s):  
High Performance Liquid Chromatography ◽  
High Performance ◽  
Paper Industry ◽  
Pulp And Paper Industry ◽  
Strength Properties ◽  
Agricultural Residues ◽  
Kraft Pulping ◽  
Pulp And Paper ◽  
Strength Increase ◽  
Xylan Content

Agricultural residues and energy crops are promising resources that can be utilized in the pulp and paper industry. This study examines the potential of co-cooking nonwood materials with hardwoods as means to incorporate nonwood material into a paper furnish. Specifically, miscanthus, switchgrass, and corn stover were substituted for poplar hardwood chips in the amounts of 10 wt %, 20 wt %, and 30 wt %, and the blends were subjected to kraft pulping experiments. The pulps were then bleached with an OD(EP)D sequence and then refined and formed into handsheets to characterize their physical properties. Surprisingly, all three co-cooked pulps showed improved strength properties (up to 35%). Sugar measurement of the pulps by high-performance liquid chromatography suggested that the strength increase correlated with enriched xylan content.

Characterization of dissolved material during the initial phase of softwood kraft pulping

TAPPI Journal ◽  
2013 ◽  
Vol 12 (1) ◽  
pp. 37-43 ◽  
Author(s):  
HANNU PAKKANEN ◽  
TEEMU PALOHEIMO ◽  
RAIMO ALÉN
Keyword(s):  
Mass Transfer ◽  
Molecular Mass ◽  
Initial Phase ◽  
Degradation Products ◽  
Kraft Pulping ◽  
Reaction Products ◽  
Cooking Temperature ◽  
Molecular Masses ◽  
Aliphatic Carboxylic Acids

The influence of various cooking parameters, such as effective alkali, cooking temperature, and cooking time on the formation of high molecular mass lignin-derived and low molecular mass carbohydrates-derived (aliphatic carboxylic acids) degradation products, mainly during the initial phase of softwood kraft pulping was studied. In addition, the mass transfer of all of these degradation products was clarified based on their concentrations in the cooking liquor inside and outside of the chips. The results indicated that the degradation of the major hemicellulose component, galactoglucomannan, typically was dependent on temperature, and the maximum degradation amount was about 60%. In addition, about 60 min at 284°F (140°C) was needed for leveling off the concentrations of the characteristic reaction products (3,4-dideoxy-pentonic and glucoisosaccharinic acids) between these cooking liquors. Compared with low molecular mass aliphatic acids, the mass transfer of soluble lignin fragments with much higher molecular masses was clearly slower.

Polysulfide-borohydride modification of southern pine alkaline pulping integrated with hydrothermal pre-extraction of hemicelluloses

TAPPI Journal ◽  
2011 ◽  
Vol 10 (7) ◽  
pp. 9-16
Author(s):  
SUNG-HOON YOON ◽  
HARRY CULLINAN ◽  
GOPAL A. KRISHNAGOPALAN
Keyword(s):  
Loblolly Pine ◽  
Sodium Borohydride ◽  
Kraft Pulping ◽  
Hot Water ◽  
Pulp Yield ◽  
Paper Strength ◽  
Southern Pine ◽  
Two Stage ◽  
Simultaneous Treatment ◽  
Process Modification

We studied three process modifications to investigate their effects on the property and yield recovery capabilities of kraft pulping integrated with hemicellulose pre-extraction of southern pine. Loblolly pine chips were pre-extracted with hot water until the sugar extraction yield reached the targeted value of 10% and then subjected to conventional and modified kraft pulping. Modification included polysulfide pretreatment; polysulfide-sodium borohydride dual pretreatment, and polysulfide followed by polysulfide-sodium borohydride dual pretreatment two-stage pretreatments prior to kraft pulping. In the first modification, about 5% of the lost pulp yield (total 7%) caused by hemicellulose pre-extraction could be recovered with 15%-20% polysulfide pretreatment. Complete recovery (7%) was achieved with simultaneous pretreatment using 15% polysulfide and 0.5% sodium borohydride with 0.1% anthraquinone in polysulfide-sodium borohydride dual pretreatment. Two-stage pretreatment using recycled 15% polysulfide followed by simultaneous treatment of 6% polysulfide and 0.4%–0.5% sodium borohydride with 0.1% anthraquinone also achieved 100% yield recovery. Continuous recycling of 15% polysulfide employed in the two-stage process modification maintained its yield protection efficiency in a repeated recycling cycle. No significant changes in paper strength were found in handsheets prepared from the three process modifications, except for a minor reduction in tear strength.

Pilot trials of hemicelluloses extraction prior to thermomechanical pulp production: Part 1

TAPPI Journal ◽  
2011 ◽  
Vol 10 (5) ◽  
pp. 21-28 ◽  
Author(s):  
CARL HOUTMAN ◽  
ERIC HORN
Keyword(s):  
Oxalic Acid ◽  
Energy Savings ◽  
Wood Chip ◽  
Strength Properties ◽  
Thermomechanical Pulp ◽  
Sugar Solution ◽  
Bisulfite Treatment ◽  
Pilot Trials ◽  
Pulp Production ◽  
Production Part

Pilot data indicate that wood chip pretreatment with oxalic acid reduced the specific energy required to make thermomechanical pulp. A combined oxalic acid/bisulfite treatment resulted in 21% refiner energy savings and 13% increase in brightness for aspen. A low level of oxalic acid treatment was effective for spruce. Energy savings of 30% was observed with no significant change in strength properties. Adding bisulfite did not significantly increase the brightness of the spruce pulp. For pine, the optimum treatment was a moderate level of oxalic acid, which resulted in 34% energy savings and an increase in strength properties. For all of these treatments 1–3 w/w % carbohydrates were recovered, which can be fermented to produce ethanol. The extract sugar solution contained significant quantities of arabinose.

Sign in / Sign up

Export Citation Format

Share Document