scholarly journals Numerical Investigations and Analysis of Cu2ZnSnS4Based Solar Cells by SCAPS-1D

2016 ◽  
Vol 2016 ◽  
pp. 1-9 ◽  
Author(s):  
M. Djinkwi Wanda ◽  
S. Ouédraogo ◽  
F. Tchoffo ◽  
F. Zougmoré ◽  
J. M. B. Ndjaka
Keyword(s):  
Solar Cells ◽  
Current Density ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Absorber Layer ◽  
Absorber Thickness ◽  
Diode Behavior ◽  
Conversion Efficiencies

This paper reports numerical investigation, using SCAPS-1D program, of the influence of Cu2ZnSnS4(the so-called CZTS) material features such as thickness, holes, and defects densities on the performances of ZnO:Al/i-ZnO/CdS/CZTS/Mo solar cells structure. We found that the electrical parameters are seriously affected, when the absorber thickness is lower than 600 nm, mainly due to recombination at CZTS/Molybdenum interface that causes the short-circuit current density loss of 3.6 mA/cm2. An additional source of recombination, inside the absorber layer, affects the short-circuit current density and produces a loss of about 2.1 mA/cm2above this range of absorber thickness. TheJ-Vcharacteristic shows that the performance of the device is also limited by a double diode behavior. This effect is reduced when the absorber layer is skinny. Our investigations showed that, for solar cells having a CZTS absorber layer of thin thickness and high-quality materials (defects density ~1015 cm−3), doping less than 1016 cm−3is especially beneficial. Such CZTS based solar cell devices could lead to conversion efficiencies higher than 15% and to improvement of about 100 mV on the open-circuit voltage value. Our results are in conformity with experimental reports existing in the literature.

scholarly journals Effect of the Phosphorus Gettering on Si Heterojunction Solar Cells

2012 ◽  
Vol 2012 ◽  
pp. 1-7 ◽  
Author(s):  
Hyomin Park ◽  
Sung Ju Tark ◽  
Chan Seok Kim ◽  
Sungeun Park ◽  
Young Do Kim ◽  
...  
Keyword(s):  
Solar Cells ◽  
Current Density ◽  
Crystalline Silicon ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Solar Simulator ◽  
Heterojunction Solar Cells ◽  
Crystalline Silicon Solar Cells

To improve the efficiency of crystalline silicon solar cells, should be collected the excess carrier as much as possible. Therefore, minimizing the recombination both at the bulk and surface regions is important. Impurities make recombination sites and they are the major reason for recombination. Phosphorus (P) gettering was introduced to reduce metal impurities in the bulk region of Si wafers and then to improve the efficiency of Si heterojunction solar cells fabricated on the wafers. Resistivity of wafers was measured by a four-point probe method. Fill factor of solar cells was measured by a solar simulator. Saturation current and ideality factor were calculated from a dark current density-voltage graph. External quantum efficiency was analyzed to assess the effect of P gettering on the performance of solar cells. Minority bulk lifetime measured by microwave photoconductance decay increases from 368.3 to 660.8 μs. Open-circuit voltage and short-circuit current density increase from 577 to 598 mV and 27.8 to 29.8 mA/cm2, respectively. The efficiency of solar cells increases from 11.9 to 13.4%. P gettering will be feasible to improve the efficiency of Si heterojunction solar cells fabricated on P-doped Si wafers.

Simultaneous Enhancement of Open-Circuit Voltage, Short-Circuit Current Density, and Fill Factor in Polymer Solar Cells

2011 ◽  
Vol 23 (40) ◽  
pp. 4636-4643 ◽  
Author(s):  
Zhicai He ◽  
Chengmei Zhong ◽  
Xun Huang ◽  
Wai-Yeung Wong ◽  
Hongbin Wu ◽  
...  
Keyword(s):  
Solar Cells ◽  
Current Density ◽  
Fill Factor ◽  
Open Circuit Voltage ◽  
Polymer Solar Cells ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit

An efficient method to achieve a balanced open circuit voltage and short circuit current density in polymer solar cells

2016 ◽  
Vol 4 (21) ◽  
pp. 8291-8297 ◽  
Author(s):  
Dongfeng Dang ◽  
Pei Zhou ◽  
Linrui Duan ◽  
Xichang Bao ◽  
Renqiang Yang ◽  
...  
Keyword(s):  
Solar Cells ◽  
Current Density ◽  
Efficient Method ◽  
Open Circuit Voltage ◽  
Polymer Solar Cells ◽  
Short Circuit ◽  
Energy Levels ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit

Good light harvesting properties and matched energy levels as well as enhanced Jsc value and high Voc value in solar cells were achieved simultaneously by construction of the D–A–π–A type regular terpolymers of PIDT-DTQ-TT, finally leading to the maximum PCE value of 6.63% in PSCs.

Approach to tune short-circuit current and open-circuit voltage of dye-sensitized solar cells: π-linker modification and photoanode selection

RSC Advances ◽  
2014 ◽  
Vol 4 (80) ◽  
pp. 42252-42259 ◽  
Author(s):  
Shengbo Zhu ◽  
Zhongwei An ◽  
Xinbing Chen ◽  
Pei Chen ◽  
Qianfeng Liu
Keyword(s):  
Solar Cells ◽  
Current Density ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Dye Sensitized ◽  
Sensitized Solar Cells

The modification of the π-linker of cyclic thiourea functionalized dyes has a significant effect on the short-circuit current density and open-circuit voltage of dye-sensitized solar cells.

Porous Silicon Antireflection Coating for Solar Cells Using Chemical Etching in HF-FeCl3-H2O

2016 ◽  
Vol 22 ◽  
pp. 1-6 ◽  
Author(s):  
Rachid Chaoui ◽  
Bedra Mahmoudi ◽  
Yasmine Si Ahmed
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Current Density ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Relative Improvement ◽  
Cell Conversion

Stain etching of silicon solar cells in HF-FeCl3-H2O solutions as a last step in the processing sequence is reported. The etching was carried out without protecting the screen printed contacts. Following optimization of the solution composition and using very short etching times to alleviate the contact degradation problem, the solar cell weighted reflectance (Rw) between 400 and 1100 nm could be reduced from 38.23% to 11.54%. For the best small area cell (~20 cm2), the PS antireflective layer led to a relative improvement of 62.74% in the short-circuit current density, the FF was enhanced by 5.5% absolute, the open-circuit voltage was increased by 1.2 mV and the cell conversion efficiency was raised by 4.1% absolute from 5.4% to 9.5%. The best large area cell (~78 cm2) shows the following changes after porous layer formation: a relative improvement of 45.43% in the short-circuit current density, an improvement in the FF of 7.4% absolute, an increase in the open-circuit voltage by 7.5 mV and an enhancement in the cell efficiency by 4.0% absolute from 6.2% to 10.2%. This method shows a great potential for the cost-effective reduction of reflectance losses in industrial silicon solar cell manufacturing.

scholarly journals CdTe-Based Thin Film Solar Cells: Past, Present and Future

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1684
Author(s):  
Alessandro Romeo ◽  
Elisa Artegiani
Keyword(s):  
Thin Film ◽  
Solar Cells ◽  
Solar Cell ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Early Years ◽  
Solar Cell Efficiency ◽  
Cell Efficiency

CdTe is a very robust and chemically stable material and for this reason its related solar cell thin film photovoltaic technology is now the only thin film technology in the first 10 top producers in the world. CdTe has an optimum band gap for the Schockley-Queisser limit and could deliver very high efficiencies as single junction device of more than 32%, with an open circuit voltage of 1 V and a short circuit current density exceeding 30 mA/cm2. CdTe solar cells were introduced at the beginning of the 70s and they have been studied and implemented particularly in the last 30 years. The strong improvement in efficiency in the last 5 years was obtained by a new redesign of the CdTe solar cell device reaching a single solar cell efficiency of 22.1% and a module efficiency of 19%. In this paper we describe the fabrication process following the history of the solar cell as it was developed in the early years up to the latest development and changes. Moreover the paper also presents future possible alternative absorbers and discusses the only apparently controversial environmental impacts of this fantastic technology.

scholarly journals Ultrathin Cu(In,Ga)Se2 Solar Cells with Ag/AlOx Passivating Back Reflector

Energies ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4268
Author(s):  
Jessica de Wild ◽  
Gizem Birant ◽  
Guy Brammertz ◽  
Marc Meuris ◽  
Jef Poortmans ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Solar Cells ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Electron Microscopic ◽  
Current Increase ◽  
Time Resolved ◽  
Cigs Solar Cells

Ultrathin Cu(In,Ga)Se2 (CIGS) absorber layers of 550 nm were grown on Ag/AlOx stacks. The addition of the stack resulted in solar cells with improved fill factor, open circuit voltage and short circuit current density. The efficiency was increased from 7% to almost 12%. Photoluminescence (PL) and time resolved PL were improved, which was attributed to the passivating properties of AlOx. A current increase of almost 2 mA/cm2 was measured, due to increased light scattering and surface roughness. With time of flight—secondary ion mass spectroscopy, the elemental profiles were measured. It was found that the Ag is incorporated through the whole CIGS layer. Secondary electron microscopic images of the Mo back revealed residuals of the Ag/AlOx stack, which was confirmed by energy dispersive X-ray spectroscopy measurements. It is assumed to induce the increased surface roughness and scattering properties. At the front, large stains are visible for the cells with the Ag/AlOx back contact. An ammonia sulfide etching step was therefore applied on the bare absorber improving the efficiency further to 11.7%. It shows the potential of utilizing an Ag/AlOx stack at the back to improve both electrical and optical properties of ultrathin CIGS solar cells.

Sign in / Sign up

Export Citation Format

Share Document