scholarly journals High-Power Laser Cutting of Steel Plates: Heat Affected Zone Analysis

2016 ◽  
Vol 2016 ◽  
pp. 1-8 ◽  
Author(s):  
Imed Miraoui ◽  
Mohamed Boujelbene ◽  
Mouna Zaied
Keyword(s):  
Heat Affected Zone ◽  
Laser Power ◽  
Laser Cutting ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Beam Diameter ◽  
Laser Beam Diameter ◽  
Melted Zone ◽  
Zone Depth ◽  
Cut Surface

The thermal effect of CO2high-power laser cutting on cut surface of steel plates is investigated. The effect of the input laser cutting parameters on the melted zone depth (MZ), the heat affected zone depth (HAZ), and the microhardness beneath the cut surface is analyzed. A mathematical model is developed to relate the output process parameters to the input laser cutting parameters. Three input process parameters such as laser beam diameter, cutting speed, and laser power are investigated. Mathematical models for the melted zone and the heat affected zone depth are developed by using design of experiment approach (DOE). The results indicate that the input laser cutting parameters have major effect on melted zone, heat affected zone, and microhardness beneath cut surface. The MZ depth, the HAZ depth, and the microhardness beneath cut surface increase as laser power increases, but they decrease with increasing cutting speed. Laser beam diameter has a negligible effect on HAZ depth but it has a remarkable effect on MZ depth and HAZ microhardness. The melted zone depth and the heat affected zone depth can be reduced by increasing laser cutting speed and decreasing laser power and laser beam diameter.

Analysis of Roughness and Heat Affected Zone of Steel Plates Obtained by Laser Cutting

2014 ◽  
Vol 974 ◽  
pp. 169-173 ◽  
Author(s):  
Imed Miraoui ◽  
Mohamed Boujelbene ◽  
Emin Bayraktar
Keyword(s):  
Surface Roughness ◽  
Laser Beam ◽  
Heat Affected Zone ◽  
Laser Power ◽  
Laser Cutting ◽  
Major Effect ◽  
Steel Plates ◽  
Beam Diameter ◽  
Laser Beam Diameter ◽  
Cut Surface

In the present study, high-power CO2 laser cutting of steel plates has been investigated and the effect of the input laser cutting parameters on the cut surface quality is analyzed. The average roughness of the cut surface of the specimens, produced by different laser beam diameter and laser power, were measured by using roughness tester. The scanning electron microscopy SEM is used to record possible metallurgical alterations on the cut edge. The aim of this work is to investigate the effect of laser beam diameter and laser power on the cut surface roughness and on the heat affected zone width HAZ of steel plates obtained by CO2 laser cutting. An overall optimization was applied to find out the optimal cutting setting that would improve the cut surface quality. It was found that laser beam diameter has a negligible effect on surface roughness but laser power had major effect on roughness. The cut surface roughness decreases as laser power increases. Improved surface roughness can be obtained at higher laser power. Also, laser beam diameter and laser power had major effect on HAZ width. It increases as laser power increases.

Effects of Laser Cutting Main Parameters on Microhardness and Microstructure Changes of Stainless Steel

2013 ◽  
Vol 664 ◽  
pp. 811-816 ◽  
Author(s):  
Imed Miraoui ◽  
Mohamed Boujelbene ◽  
Emin Bayraktar
Keyword(s):  
Stainless Steel ◽  
Laser Power ◽  
Laser Cutting ◽  
Cutting Speed ◽  
Experimental Tests ◽  
Cutting Parameters ◽  
Surface Microstructure ◽  
Machined Surface ◽  
Microhardness And Microstructure ◽  
Cut Surface

Laser cutting of materials is becoming the preferred method of cutting. It has many advantages over conventional machining techniques such as better quality of cuts, quick and accurate cutting. The objective of this work is to investigate the effect of the main input laser cutting parameters, laser power and cutting speed, on the microhardness of stainless steel sheets obtained by CO2 laser cutting. The experimental tests were performed at various laser powers and cutting speeds. The cut surface was studied based on microhardness depth profiles beneath the machined surface. In order to investigate the metallurgical alterations beneath the cut surface, the microstructure was observed by using scanning electron microscopy. The results show that the microhardness and the surface microstructure are affected by laser cutting. Laser cutting leads to the formation of periodic striations and cracks. Also the main parameters of cutting, laser power and cutting speed, have an effect on surface microstructure and microhardness.

scholarly journals Analysis of the heat affected zone in CO2 laser cutting of stainless steel

2012 ◽  
Vol 16 (suppl. 2) ◽  
pp. 363-373 ◽  
Author(s):  
Milos Madic ◽  
Miroslav Radovanovic
Keyword(s):  
Neural Network ◽  
Artificial Neural Network ◽  
Heat Affected Zone ◽  
Laser Power ◽  
Laser Cutting ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Data Sets ◽  
Focus Position ◽  
Artificial Neural

This paper presents an investigation into the effect of the laser cutting parameters on the heat affected zone in CO2 laser cutting of AISI 304 stainless steel. The mathematical model for the heat affected zone was expressed as a function of the laser cutting parameters such as the laser power, cutting speed, assist gas pressure and focus position using the artificial neural network. To obtain experimental database for the artificial neural network training, laser cutting experiment was planned as per Taguchi?s L27 orthogonal array with three levels for each of the cutting parameter. Using the 27 experimental data sets, the artificial neural network was trained with gradient descent with momentum algorithm and the average absolute percentage error was 2.33%. The testing accuracy was then verified with 6 extra experimental data sets and the average predicting error was 6.46%. Statistically assessed as adequate, the artificial neural network model was then used to investigate the effect of the laser cutting parameters on the heat affected zone. To analyze the main and interaction effect of the laser cutting parameters on the heat affected zone, 2-D and 3-D plots were generated. The analysis revealed that the cutting speed had maximum influence on the heat affected zone followed by the laser power, focus position and assist gas pressure. Finally, using the Monte Carlo method the optimal laser cutting parameter values that minimize the heat affected zone were identified.

Effect of Laser Beam Diameter on Cut Edge of Steel Plates Obtained by Laser Machining

2013 ◽  
Vol 467 ◽  
pp. 227-232 ◽  
Author(s):  
Imed Miraoui ◽  
Mouna Zaied ◽  
Mohamed Boujelbene
Keyword(s):  
Laser Beam ◽  
Laser Cutting ◽  
Steel Plates ◽  
Beam Diameter ◽  
Power Laser ◽  
Laser Beam Diameter ◽  
Machined Surface ◽  
Cut Edge ◽  
Thermal Influence ◽  
Cut Surface

Laser cutting is a thermal process which is used contactless to separate materials. In the present study, high-power laser cutting of steel plates is considered and the thermal influence of laser cutting on the cut edges is examined. The microstructure and the microhardness of the cut edge are affected by the input laser cutting parameter: laser beam diameter. The aim of this work is to investigate the effect of the laser beam diameter on the microhardness beneath the cut surface of steel plates obtained by CO2 laser cutting. The cut surface was studied based on microhardness depth profiles beneath the machined surface. The results show that laser cutting has a thermal effect on the surface microstructure and on the microhardness beneath the cut section. Also the microhardness of the hardening zone depends on the laser beam diameter.

Laser Cutting Quality of the Ceramic Slabs

2006 ◽  
Vol 505-507 ◽  
pp. 847-852 ◽  
Author(s):  
Xu Yue Wang ◽  
Wen Ji Xu ◽  
Ren Ke Kang ◽  
Yi De Liang
Keyword(s):  
Laser Power ◽  
Laser Cutting ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Incident Laser Power ◽  
Focal Position ◽  
Geometrical Features ◽  
The Relationship ◽  
Cutting System

An experimental analysis is presented which investigates the relationship between cutting parameters and the volume of material removal as well as its cutting quality on a Nd:YAG laser cutting system. The parameters that varied on two testing thickness during cutting include cutting speed, incident laser power and focal position in a continuous through cut. Various trends of the kerf geometrical features in terms of the varying process parameters are analyzed and shown to be reasonable. Discussions are also given on kerf geometry control in situations with cutting parameters. It shows that the effects of varying parameters such as cutting speed, laser power and focal position on cutting kerf width, surface roughness, and striation that have provided a deeper understanding of the laser machining.

A Parametric Optimization on Cutting Force during Laser Assisted Machining of Inconel 718 Alloy

2015 ◽  
Vol 787 ◽  
pp. 460-464 ◽  
Author(s):  
M. Vignesh ◽  
K. Venkatesan ◽  
R. Ramanujam ◽  
P. Kuppan
Keyword(s):  
Cutting Force ◽  
Feed Rate ◽  
Inconel 718 ◽  
Laser Power ◽  
Laser Cutting ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Work Piece ◽  
Conventional Machining

Inconel 718, a nickel based alloys, addressed as difficult to cut material because of hard carbide particle, hardness, work hardening and low thermal conductivity. Improving the machinability characteristics of nickel based alloys is a major anxiety in aircraft, space vehicle and other manufacturing fields. This paper presents an experimental investigation in Laser assisted turning of Inconel 718 to determine the effects of laser cutting parameters on cutting temperature and cutting forces. This nickel alloy has a material hardness at 48 HRC and machined with TICN/Al2O3/TiN tool. This is employed for the manufacture of helicopter rotor blades and cryogenic storage tanks. The experiments were conducted at One-Factor-at-a-Time.The effects of laser cutting parameters, namely cutting speed, feed rate, laser power and laser to work piece angle, on the cutting temperature and cutting force components, are critically analysed and the results are compared with unassisted machining of this alloy. The experiments are conducted by varying the cutting speed at three levels (50, 75, 100 m/min), feed rate (0.05, 0.075 0.1 mm/rev), laser power (1.25 kW, 1.5 kW, 1.75 kW) and at two level laser to work piece angle (60, 75°). At the optimal parametric combinationof laser power 1.5 kW with cutting speed of 75m/min, feed rate of 0.075 mm/min and laser to work piece angle 60°, the benefit of LAM was shown by 18%, 25% and 24% decrease in feed force (Fx), thrust force (Fy) and cutting force (Fz) as compared to those of the conventional machining. Examination of the machined surface hardness profiles showed no change under LAM and conventional machining.

scholarly journals Surface Quality of Ti-6Al-4V Titanium Alloy Parts Machined by Laser Cutting

2020 ◽  
Vol 10 (4) ◽  
pp. 6062-6067
Author(s):  
A. Boudjemline ◽  
M. Boujelbene ◽  
E. Bayraktar
Keyword(s):  
Experimental Data ◽  
Surface Roughness ◽  
Titanium Alloy ◽  
Laser Power ◽  
Laser Cutting ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Maximum Height ◽  
Proposed Model

This paper investigates high power CO2 laser cutting of 5mm-thick Ti-6Al-4V titanium alloy sheets, aiming to evaluate the effects of various laser cutting parameters on surface roughness. Using multiple linear regression, a mathematical model based on experimental data was proposed to predict the maximum height of the surface Sz as a function of two laser cutting parameters, namely cutting speed and assist-gas pressure. The adequacy of the proposed model was validated by Analysis Of Variance (ANOVA). Experimental data were compared with the model’s data to verify the capacity of the proposed model. The results indicated that for fixed laser power, cutting speed is the predominant cutting parameter that affects the maximum height of surface roughness.

scholarly journals Influence of cutting parameters on the quality of the cut surfaces of steel swith a laser beam

2019 ◽  
Vol 44 (1) ◽  
pp. 21-27
Author(s):  
Dobre Runchev ◽  
Filip Zdraveski ◽  
Irena Ivanova
Keyword(s):  
Laser Beam ◽  
Laser Cutting ◽  
Visual Inspection ◽  
Cutting Speed ◽  
Base Material ◽  
Cutting Parameters ◽  
Thermal Cutting ◽  
Materials Used ◽  
Cut Surface

The main objective of the research covered in this paper is to present results for the quality of surfaces thermally cut with a laser beam. The variety of steel materials used as samples on which laser cutting is performed are the following Č.0146 (1.0330), Č.0147 (1.0333), Č.2131 (1.5024), SS Ferbec CR, HARDOX 450 and HARDOX 550. Thermal cutting is carried out with a CNC controlled Fiber laser BAYKAL type BLS–F–1530. The quality of the cut surface is analyzed based on varying the power of the laser beam, changing cutting speed and the type of additional gas (oxygen, air and nitrogen). By visual inspection, measuring the roughness of the cut surface and measuring the width of the intersection, it is determined the influence of the factors like type of the base material, type of gases, the power of thelaser beam and the cutting speed, in accordance with the standards DIN EN ISO 9013-2002 and the JUS C.T3.022.

scholarly journals Analysis of neodymium-doped yttrium-aluminum-garnet laser and experimental prospects for cutting micro-thin black walnut veneers in industry

BioResources ◽  
2021 ◽  
Vol 16 (2) ◽  
pp. 2416-2432
Author(s):  
Bakary S. Doumbia ◽  
Chunmei Yang ◽  
Yan Ma ◽  
Ting Jiang ◽  
Xiang Li ◽  
...  
Keyword(s):  
Process Parameters ◽  
Laser Power ◽  
Laser Cutting ◽  
Yttrium Aluminum Garnet ◽  
Cutting Speed ◽  
Black Walnut ◽  
Kerf Width ◽  
Machining Parameters ◽  
Protection Measures ◽  
Cut Surface

By structurally and practically analyzing the use of Nd: YAG laser for cutting black walnut veneer, this study considered practical and environmental concerns regarding the global warming protection measures. A numerical model of laser wood veneer cutting was based on the relation between process parameters and the material thickness. A pulsed Nd: YAG was used to cut black walnut veneer of 0.3 mm thickness under different machining conditions regarding laser power and cutting speed to study the cut kerf width. An analysis of variance was conducted to test the significance of machining parameters. The parameters studied were laser power, cutting speed, kerf width, cut surface, safety, and eco-friendliness. The results showed that the kerf width decreased significantly with increased cut speed and, inversely, by laser output power. An efficient cut with a narrow kerf, clean and smooth, with less burn, was possible at laser cutting speeds of 2.5, 5.0, and 5.5 mm/s with kerf widths of 0.544, 0.69, 0.62 mm, respectively. As multiple factors affect the micro-thin wood laser cutting process, finding the optimal process parameters is crucial for successful machining with no burn effect.

An investigation on cutting of the MWCNTs doped composite plates by CO2 laser beam

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Ferhat Ceritbinmez ◽  
Ahmet Yapici
Keyword(s):  
Composite Materials ◽  
Laser Beam ◽  
Laser Power ◽  
Laser Cutting ◽  
Fiber Composite ◽  
Cutting Speed ◽  
Multiwall Carbon Nanotubes ◽  
Composite Plates ◽  
Cutting Parameters ◽  
Content Type

Purpose The purpose of this study is to obtain strong materials with multiwall carbon nanotubes (MWCNTs) doped and investigate laser cut of MWCNTs also find the effect of the laser cutting parameters on composite materials. Design/methodology/approach The laminated composite plates were manufactured by using a vacuum infusion process. The mechanical properties of the composite materials produced were determined according to American Society for Testing and Materials (ASTM) D3039M, ASTM D3171, ASTM D 792 and ASTM D2583. A 130 Watts carbondioxide (CO2) laser cutting machine was used for drilling the two different composite plates with a thickness of 1.6–1.5 mm. Three variables were considered as process parameters including laser power (in three levels of 84.50, 104.00 and 127.40 W), cutting speed (in three levels of 4, 6, 8 mm/s) and 14 mm fixed focal position. Findings The fibers could not be cut due to insufficient melting in the experiments performed using 84.50 and 104.00 W laser power but the cutting was successfully completed when the laser power was 127.40 W. However, as the cutting speed increased, the contact time of the laser beam with the material decreased, so the kerf decreased, but the increased laser power created a thermal effect, causing an increase in hardness around the cutting surface. This increase was lower in MWCNTs doped composites compared to pure composites. It has been found that the addition of nanoparticles to layered glass fiber composite materials played an effective role in the strength of the material and affected the CO2 laser cutting quality. Originality/value This study is a unique study in which the CO2 laser cutting method of MWCNT-doped composite materials was investigated and the machinability without cutting errors, such as delamination, splitting, distortion and burring using the most suitable laser cutting parameters was revealed.

Sign in / Sign up

Export Citation Format

Share Document