scholarly journals Evaluation of the Performance and Microstructure of Ecofriendly Construction Bricks Made with Fly Ash and Residual Rice Husk Ash

2015 ◽  
Vol 2015 ◽  
pp. 1-11 ◽  
Author(s):  
Chao-Lung Hwang ◽  
Trong-Phuoc Huynh
Keyword(s):  
Fly Ash ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Microstructural Characterization ◽  
Fine Aggregate ◽  
Potential Candidate ◽  
X Ray Diffraction ◽  
Steel Mold ◽  
Fine Aggregates ◽  
Class F Fly Ash

This research presents the engineering performance and the microstructural characterization of ecofriendly construction bricks that were produced using a binder material made from a mixture of class-F fly ash (FA) and residual rice husk ash (RHA). Unground rice husk ash (URHA) was used as a partial fine aggregate substitute (0–40%). The solid bricks of 220 × 105 × 60 mm in size were prepared by mixing FA and RHA with an alkaline solution and fine aggregates, formed by compressing the mixture in a steel mold under 35 MPa of forming pressure, and then cured at 35°C and 50% relative humidity until the required testing ages. The tests of compressive strength, water absorption, and bulk density were conducted in accordance with relevant Vietnamese standards in order to estimate the effect of the URHA content on the engineering performance of the hardened bricks. Scanning electron microscopy (SEM), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR) were performed to determine the microstructure and the phase composition of the brick samples. The results show that properties of these bricks conformed to relevant Vietnamese standards. Therefore, FA and RHA are potential candidate materials for producing ecofriendly construction bricks using geopolymerization technology.

Properties of Unfired Building Bricks Prepared from Fly Ash and Residual Rice Husk Ash

2015 ◽  
Vol 754-755 ◽  
pp. 468-472 ◽  
Author(s):  
Chao Lung Hwang ◽  
Trong Phuoc Huynh
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Fine Aggregate ◽  
Test Results ◽  
Design Algorithm ◽  
Potential Applications ◽  
Hardened Properties

This work investigates the possibility of using fly ash (FA) and Vietnam residual rice husk ash (RHA) in producing unfired building bricks with applying densified mixture design algorithm (DMDA) method. In this research, little amount of cement was added into the mixtures as binder substitution. Unground rice husk ash (URHA), an agricultural by-product, was used as partial fine aggregate replacement (10% and 30%) in the mixtures. The solid bricks of 220×105×60 mm in size were prepared in this study. The hardened properties of the bricks were investigated including compressive strength, flexural strength and water absorption according to corresponding Vietnamese standards. Forming pressure of 35 MPa was applied to form the solid bricks in the mold. The test results show that all brick specimens obtained good mechanical properties, which were well conformed to Vietnamese standard. Compressive strength and flexural strength of the bricks were respectively in range of 13.81–22.06 MPa and 2.25–3.47 MPa. It was definitely proved many potential applications of FA and RHA in the production of unfired building bricks.

scholarly journals PENGARUH CAMPURAN ABU SEKAM PADI DAN ABU ARANG TEMPURUNG SEBAGAI PENGGANTI SEBAGIAN AGREGAT HALUS TERHADAP KUAT TEKAN BETON

2021 ◽  
Vol 1 (1) ◽  
pp. 1
Author(s):  
Agung Prayogi
Keyword(s):  
Compressive Strength ◽  
Rice Husk ◽  
Coarse Aggregate ◽  
Rice Husk Ash ◽  
Fine Aggregate ◽  
Concrete Compressive Strength ◽  
Fine Aggregates ◽  
Compressive Strength Of Concrete ◽  
Average Compressive Strength ◽  
By Products

Abstract Concrete is the most widely used material throughout the world and innovations continue to be carried out to produce efficient development. Shell charcoal ash and rice husk ash are industrial by-products which have the potential to replace sand for concrete mix, especially in Indragiri Hilir. The research with the title "Effect of Mixture of Rice Husk Ash and Shell Ash Ashes as Substitute for Some Fine Aggregates Against Concrete Compressive Strength" aims to prove the effect of a mixture of shell charcoal ash and husk ash to replace some of the sand to produce maximum compressive strength. Concrete is a mixture of Portland cement, fine aggregate, coarse aggregate, and water. This research uses 5 variations of the mixture to the weight of sand, BSA 0 without a substitute mixture, BSA 1 with a mixture of 5% husk ash and 10% shell charcoal, BSA 2 with a mixture of 5% husk ash and 15% charcoal ash, BSA 3 with a mixture of 5% husk ash and 18% charcoal, BSA 4 with a mixture of 10% husk and 10% charcoal, and BSA 5 with a mixture of 13% husk ash and 10% charcoal ash. SNI method is used for the Job Mix Formula (JMF) mixture in this research. The results of the average compressive strength of concrete at 28 days for JMF of 21.05 MPa, BSA 1 of 23.68 MPa, BSA 2 of 22.23 MPa, BSA 3 of 14.39 MPa, BSA 4 of 13.34 MPa , and BSA 5 of 20.14 MPa. The conclusion drawn from the results of the BSA 1 research with a mixture of 5% husk ash and 15% charcoal ash produced the highest average compressive strength of 23.68 MPa. Abstrak Beton merupakan material paling banyak digunakan diseluruh dunia dan terus dilakukan inovasi untuk menghasilkan pembangunan yang efisien. Abu arang tempurung dan abu sekam padi merupakan hasil sampingan industri yang berpotensi sebagai pengganti pasir untuk campuran beton, khususnya di Indragiri Hilir. Penelitian dengan judul “Pengaruh Campuran Abu Sekam Padi dan Abu Arang Tempurung Sebagai Pengganti Sebagian Agregat Halus Terhadap Kuat Tekan Beton” ini bertujuan membuktikan adanya pengaruh campuran abu arang tempurung dan abu sekam untuk mengganti sebagian pasir hingga menghasilkan kuat tekan maksimum. Beton adalah campuran antara semen portland, agregat halus, agregat kasar, dan air. Penelitian ini menggunakan 5 variasi campuran terhadap berat pasir, BSA 0 tanpa campuran pengganti, BSA 1 dengan campuran 5 % abu sekam dan 10% arang tempurung, BSA 2 dengan campuran 5% abu sekam dan 15% abu arang, BSA 3 dengan campuran 5% abu sekam dan 18% arang, BSA 4 dengan campuran 10% sekam dan 10% arang, dan BSA 5 dengan campuran 13% abu sekam dan 10% abu arang. Metode SNI digunakan untuk campuran Job Mix Formula (JMF)  pada penelitian ini. Hasil rata-rata kuat tekan beton pada umur 28 hari untuk JMF sebesar 21,05 MPa, BSA 1 sebesar 23,68 MPa, BSA 2 sebesar 22,23 MPa, BSA 3 sebesar 14,39 MPa, BSA 4 sebesar 13,34 MPa, dan BSA 5 Sebesar 20,14 MPa. Ditarik kesimpulan dari hasil penelitian BSA 1 dengan campuran 5% abu sekam dan 15% abu arang menghasilkan rata-rata kuat tekan tertinggi yaitu sebesar 23,68 MPa.  

scholarly journals Effect of Fine Aggregate Particle Characteristics on Mechanical Properties of Fly Ash-Based Geopolymer Mortar

Minerals ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 897
Author(s):  
Heng Li ◽  
Pengpeng Gao ◽  
Fang Xu ◽  
Tao Sun ◽  
Yu Zhou ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Pass Rate ◽  
Fine Aggregate ◽  
X Ray Diffraction ◽  
River Sand ◽  
Fine Aggregates ◽  
Compressive And Flexural Strengths ◽  
Filling Coefficient ◽  
Fineness Modulus

This research aimed to investigate the effect of fine aggregate particles on mechanical properties of fly ash-based geopolymer mortar. In this work, seven kinds of river sand particles were designed based on different fine aggregate characteristics. The fineness modulus was adopted to quantitatively describe the gradation of sands. The fluidity, compressive, flexural, and tensile strengths of geopolymer mortar with different sand gradations were analyzed by laboratory tests. Furthermore, the composition and morphology of fly ash-based geopolymer mortar was analyzed by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The reasonable gradation range and filling effect of sand were obtained. The results show that fluidity and compressive and flexural strengths of geopolymer mortar both improve with the increase of the fineness modulus, while specific surface area and voidage are opposite. The tensile strength of mortar largely lies on the interface properties between the geopolymer binder and fine aggregates. When the pass rate of the key sieving size 1.18 mm is 75–95%, the pass rate of the key sieving size 0.15 mm is 15–25%, the fineness modulus is 2.2–2.6 and the appropriate filling coefficient of geopolymer paste is around 1.0–1.15, the comprehensive performance of geopolymer mortar is the best. This research paper could provide a basis for the design of geopolymer mortar based on fly ash, and it is of great significance for its popularization and application.

Life cycle assessment and cost analysis of fly ash–rice husk ash blended alkali-activated concrete

2021 ◽  
Vol 295 ◽  
pp. 113140
Author(s):  
Sarah Fernando ◽  
Chamila Gunasekara ◽  
David W. Law ◽  
M.C.M. Nasvi ◽  
Sujeeva Setunge ◽  
...  
Keyword(s):  
Life Cycle Assessment ◽  
Life Cycle ◽  
Fly Ash ◽  
Cost Analysis ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Alkali Activated Concrete ◽  
Alkali Activated

Sulfate resistance of blended cements containing fly ash and rice husk ash

2007 ◽  
Vol 21 (6) ◽  
pp. 1356-1361 ◽  
Author(s):  
P. Chindaprasirt ◽  
P. Kanchanda ◽  
A. Sathonsaowaphak ◽  
H.T. Cao
Keyword(s):  
Fly Ash ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Blended Cements ◽  
Sulfate Resistance

Physical Properties of Cement Mortar Containing Waste Ash

2015 ◽  
Vol 804 ◽  
pp. 129-132
Author(s):  
Sumrerng Rukzon ◽  
Prinya Chindaprasirt
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Cement Mortar ◽  
Ash Content ◽  
Water Requirement ◽  
Test Results ◽  
Pozzolanic Material ◽  
Materials Used

This research studies the potential for using waste ash from industrial and agricultural by-products as a pozzolanic material. Classified fly ash (FA) and ground rice husk ash (RA) were the materials used. Water requirement, compressive strength and porosity of cement mortar were investigated. Test results indicated that FA and RA (waste ash) have a high potential to be used as a good pozzolanic material. The water requirement of mortar mix decreases with the increases in fly ash content. For ground rice husk ash (RA), the water requirement of mortar mix increases with the increases in rice husk ash content. In addition, the reduction in porosity was associated with the increase in compressive strength.

Cleaner Environment Approach by the Utilization of Low Calcium Wood Ash in Geopolymer Concrete

2021 ◽  
Author(s):  
Kadarkarai Arunkumar ◽  
Muthiah Muthukannan ◽  
Arunachalam Suresh Kumar ◽  
Arunasankar Chithambar Ganesh ◽  
Rangaswamy Kanniga Devi
Keyword(s):  
Fly Ash ◽  
Microstructural Characterization ◽  
Wood Ash ◽  
Geopolymer Concrete ◽  
X Ray Diffraction ◽  
High Potassium ◽  
Waste Wood ◽  
Research Findings ◽  
Research Gap ◽  
The Impact

The waste disposal issues were the most severe problems that could cause global warming, which depletes the environment. The research hypothesis was to find the suitability and sustainability of utilizing the waste by-products in the invention of green geopolymer concrete to eliminate the tremendous effects caused by the wastes. Due to the increased demand for fly ash in recent years, the requirement of high alkaline activators, and elevated temperature for curing, there was a research gap to find an alternative binder. The novelty of this research was to utilize the waste wood ash, which is available plenty in nearby hotels and has an inbuilt composition of high potassium that can act as a self alkaline activator. Waste wood ash procured from the local hotels was replaced with fly ash by 0 to 100% at 10% intervals. The setting and mechanical characteristics were found on the prolonged ages to understand the influence of waste wood ash. Microstructural characterization was found using Scanning Electron Microscope and X-Ray Diffraction Analysis to define the impact of waste wood ash in the microstructure. The research findings showed that replacing 30% waste wood ash with fly ash attained better performance in setting properties and all mechanical parameters. The obtained optimum mix could provide the best alternative for fly ash in geopolymer to eliminate the economic thrust by the requirement of alkaline activators and deploy the environmental impact caused by the waste wood ash.

Development of Ternary Concrete Utilizing Agricultural Waste Material

2022 ◽  
Author(s):  
Sunita Kumari ◽  
Dhirendra Singhal ◽  
Rinku Walia ◽  
Ajay Rathee
Keyword(s):  
Rice Husk ◽  
Rice Husk Ash ◽  
Agricultural Waste ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Concrete Mix ◽  
Maize Cob

Abstract The present project proposes to utilize rice husk and maize cob husk ash in the cement to mitigate the adverse impact of cement on environment and to enhance the disposal of waste in a sustainable manner. Ternary concrete / MR concrete was prepared by using rise husk and maize cob ash with cement. For the present project, five concrete mixes MR-0 (Control mix), MR-1 (Rice husk ash 10% and MR-2.5%), MR-2 (Rice husk ash 10% and MR-5%), MR-3 (Rice husk ash 10% and MR-2.5%), MR-4 (Rice husk ash 10% and MR-2.5%) were prepared. M35 concrete mix was designed as per IS 10262:2009 for low slump values 0-25mm. The purpose is to find the optimum replacement level of cement in M35 grade ternary concrete for I – Shaped paver blocks.In order to study the effects of these additions, micro-structural and structural properties test of concretes have been conducted. The crystalline properties of control mix and modified concrete are analyzed by Fourier Transform Infrared Spectroscope (FTIR), Scanning Electron Microscopy (SEM), and X-Ray Diffraction (XRD). The results indicated that 10% Rice husk ash and 5% maize cob ash replaced with cement produce a desirable quality of ternary concrete mix having good compressive strength. The results of SEM analysis indicated that the morphology of both concrete were different, showing porous structure at 7 days age and become unsymmetrical with the addition of ashes. After 28 day age, the control mix contained more quantity of ettringite and became denser than ternary concrete. XRD analysis revealed the presence of portlandite in large quantity in controlled mix concrete while MR concrete had the partially hydrated particle of alite.

Sign in / Sign up

Export Citation Format

Share Document