scholarly journals Evaluation of Influence of Various Polymers on Dissolution and Phase Behavior of Carbamazepine-Succinic Acid Cocrystal in Matrix Tablets

2015 ◽  
Vol 2015 ◽  
pp. 1-10 ◽  
Author(s):  
Majeed Ullah ◽  
Hanif Ullah ◽  
Ghulam Murtaza ◽  
Qaisar Mahmood ◽  
Izhar Hussain
Keyword(s):  
Drug Release ◽  
Succinic Acid ◽  
Polymer Concentration ◽  
Matrix Tablets ◽  
Inverse Relation ◽  
Direct Relation ◽  
Drug Release Profile ◽  
X Ray ◽  
Opposite Trend ◽  
The Impact

The aim of current study was to explore the influence of three commonly used polymers, that is, cellulosics and noncellulosics, for example, Methocel K4M, Kollidon VA/64, and Soluplus, on the phase disproportionation and drug release profile of carbamazepine-succinic acid (CBZ-SUC) cocrystal at varying drug to polymer ratios (1 : 1 to 1 : 0.25) in matrix tablets. The polymorphic phase disproportionation during in-depth dissolution studies of CBZ-SUC cocrystals and its crystalline properties were scrutinized by X-ray powder diffractrometry and Raman spectroscopy. The percent drug release from HPMC formulations (CSH) showed inverse relation with the concentration of polymer; that is, drug release increased with decrease in polymer concentration. On contrary, direct relation was observed between percent drug release and polymer concentrations of Kollidon VA 64/Soluplus (CSK, CSS). At similar polymer concentration, drug release from pure carbamazepine was slightly lower with HPMC formulations than that of cocrystal; however, opposite trend in release rate was observed with Kollidon VA/64 and Soluplus. The significant increase in dissolution rate of cocrystal occurred with Kollidon VA/64 and Soluplus at higher polymer concentration. Moreover, no phase change took place in Methocel and Kollidon formulations. No tablet residue was left for Soluplus formulation so the impact of polymer on cocrystal integrity cannot be predicted.

scholarly journals Formulation and Evaluation of Sustained Release Matrix Tablets of Aceclofenac

2021 ◽  
Vol 4 (2) ◽  
pp. 99-109
Author(s):  
Priyanka Singh ◽  
Amit Kumar Shrivastava ◽  
Sachin Kumar ◽  
Manish Dhar Dwivedi
Keyword(s):  
Drug Release ◽  
Guar Gum ◽  
Polymer Concentration ◽  
Matrix Tablets ◽  
Hydrophilic Polymers ◽  
Wet Granulation ◽  
Drug Release Profile ◽  
In Vitro Drug Release ◽  
Study Results

This study aimed to improve the dissolution rate of aceclofenac and release the drug in a controlled manner over a period of 24 hours. Matrix tablets were prepared by direct compression method, using hydrophilic polymers (HPMC/guar gum). Matrix tablets were prepared by wet granulation method using different hydrophilic polymers (HPMC/guar gum). Tablets were evaluated for in vitro drug release profile in phosphate buffer with pH 6.8 (without enzymes). The thickness and hardness of prepared tablets were 3.23 ± 0.035 to 3.28 ± 0.008 mm and 3.26 ± 0.115 to 3.60 ± 0.200 kg/cm2, respectively. The friability was within the acceptable limits of pharmacopoeial specifications (0.31 to 0.71%), which indicates the good mechanical strength of the tablets. Drug release was retarded with an increase in polymer concentration due to the gelling property of polymers. The in vitro drug release from the proposed system was best explained by Higuchi’s model, indicating that drug release from tablets displayed a diffusion-controlled mechanism. The results clearly indicate that guar gum could be a potential hydrophilic carrier in developing oral controlled drug delivery systems. Based on the study results, formulations F8 was selected as the best formulation.

Influence of Formulation Variables and Processing Techniques on Drug Release from Carbopol-971 based Matrix Tablets of Cinnarizine and Nimodipine.

2010 ◽  
Vol 2 (1) ◽  
Author(s):  
Singh K. ◽  
Pandit K. ◽  
Mishra N.
Keyword(s):  
Drug Release ◽  
Release Rate ◽  
Polymer Concentration ◽  
Matrix Tablets ◽  
Wet Granulation ◽  
Weight Variation ◽  
Diffusion Controlled ◽  
The Matrix ◽  
Processing Techniques ◽  
Formulation Variables

The matrix tablets of cinnarizine and nimodipine were prepared with varying ratio of Carbopol- 971P and co-excipients of varying hydrophilicity (i.e. dicalcium phosphate and spray dried lactose) by direct compression and wet granulation using alcoholic mucilage. The prepared tablets were evaluated for weight variation, hardness and friability. The influence of concentration of the matrix forming material and co-excipients on the release rate of the drug was studied. The release rate of Cinnarizine (more soluble drug) from tablets followed diffusion controlled mechanism whereas for nimodipine (less soluble drug), the drug release followed case-II or super case- II transport mechanism based on Korsmeyer- Peppas equation. The results indicated that the drug release from matrix tablets was increases with increase in hydrophilicity of drug and co-excipients. The release of drug also increased with thermal treatment and decreasing polymer concentration.

Preparation and Evaluation of Gemifloxacin Mesylate Floating Matrix Tablets in Healthy Human Volunteers

2017 ◽  
Vol 10 (1) ◽  
pp. 3623-3630
Author(s):  
Bhikshapathi D. V. R. N. ◽  
Haarika B ◽  
Jyothi Sri S ◽  
K Abbulu
Keyword(s):  
Drug Release ◽  
Sodium Bicarbonate ◽  
Polymer Concentration ◽  
Hydroxypropyl Methylcellulose ◽  
Matrix Tablets ◽  
Physical Parameters ◽  
Drug Bioavailability ◽  
Floating Tablets

The purpose of present investigation was to develop floating matrix tablets of gemifloxacin mesylate, which after oral administration could prolong the gastric residence time, increase the drug bioavailability and diminish the side effects of irritating drugs. Tablets containing drug, various viscosity grades of hydroxypropyl methylcellulose such as HPMC K4M and HPMC K15M as matrix forming agent, Sodium bicarbonate as gas-forming agent and different additives were tested for their usefulness in formulating gastric floating tablets by direct compression method. The physical parameters, in vitro buoyancy, release characteristics and in vivo radiographic study were investigated in this study. The gemifloxacin mesylate floating tablets were prepared using HPMC K4M polymer giving more sustained drug release than the tablet containing HPMC K15M. All these formulations showed floating lag time of 30 to 47 sec and total floating time more than 12 h. The drug release was decreased when polymer concentration increases and gas generating agent decreases. Formulation that contains maximum concen-tration of both HPMC K15M and sodium bicarbonate (F9) showing sufficiently sustained with 99.2% of drug release at 12 h. The drug release from optimized formulation follows Higuchi model that indicates the diffusion controlled release. The best formulation (F9) was selected based on in vitro characteristics and used in vivo radiographic studies by incorporating barium sulphate as a radio-opaque agent and the tablet remained in the stomach for about 6 h.   

Evaluation of swelling properties and drug release from mechanochemical pre-gelatinized glutinous rice starch matrix tablets by near infrared spectroscopy

2021 ◽  
pp. 096703352098235
Author(s):  
Tomomi Takaku ◽  
Yusuke Hattori ◽  
Tetsuo Sasaki ◽  
Tomoaki Sakamoto ◽  
Makoto Otsuka
Keyword(s):  
Drug Release ◽  
Near Infrared ◽  
Nir Spectroscopy ◽  
Matrix Tablets ◽  
Rice Starch ◽  
Release Time ◽  
Swelling Properties ◽  
X Ray ◽  
Glutinous Rice ◽  
Pharmaceutical Properties

The effect of grinding on the pharmaceutical properties of matrix tablets consisting of ground glutinous rice starch (GRS) and theophylline (TH) was predicted by near infrared (NIR) spectroscopy. Ground GRS samples were prepared by grinding GRS in a planetary ball mill for 0-120 min, measured by X-ray diffractometry (XRD) and NIR, and then evaluated for crystallinity (%XRD) based on XRD profiles. Tablets containing TH (5 w/w%), ground GRS (94 w/w%), and magnesium stearate (1 w/w%) were formed by compression. Gel-forming and drug-release processes of the tablets were measured using a dissolution instrument with X-ray computed tomography (XCT). Swelling ratio (SWE) and mean drug-release time (MDT) were evaluated based on XCT and drug-release profiles, respectively. Calibration models for predicting percent %XRD, MDT, and SWE were constructed based on the NIR of ground GRS using partial least-squares. The results indicated the possibility of controlling the pharmaceutical properties of matrix tablets by altering the pre-gelatinization of GRS based on changes in their NIR spectra during the milling process.

scholarly journals Development and evaluation of sustained release losartan potassium matrix tablet using kollidon SR as release retardant

2012 ◽  
Vol 48 (4) ◽  
pp. 621-628 ◽  
Author(s):  
Shahid Sarwar ◽  
Mohammad Salim Hossain
Keyword(s):  
Drug Release ◽  
Sustained Release ◽  
Release Kinetics ◽  
Polymer Concentration ◽  
In Vitro Release ◽  
Matrix Tablets ◽  
Losartan Potassium ◽  
Dissolution Time ◽  
Release Mechanism ◽  
Matrix Tablet

The present study was undertaken to develop sustained release (SR) matrix tablets of losartan potassium, an angiotensin-II antagonist for the treatment of hypertension. The tablets were prepared by direct compression method, along with Kollidon SR as release retardant polymer. The amount of losartan potassium remains fixed (100 mg) for all the three formulations whereas the amounts of Kollidon SR were 250 mg, 225 mg, and 200 mg for F-1, F-2, and F-3 respectively. The evaluation involves three stages: the micromeritic properties evaluation of granules, physical property studies of tablets, and in-vitro release kinetics studies. The USP apparatus type II was selected to perform the dissolution test, and the dissolution medium was 900 mL phosphate buffer pH 6.8. The test was carried out at 75 rpm, and the temperature was maintained at 37 ºC ± 0.5 ºC. The release kinetics was analyzed using several kinetics models. Higher polymeric content in the matrix decreased the release rate of drug. At lower polymeric level, the rate and extent of drug release were enhanced. All the formulations followed Higuchi release kinetics where the Regression co-efficient (R²) values are 0.958, 0.944, and 0.920 for F-1, F-2, and F-3 respectively, and they exhibited diffusion dominated drug release. Statistically significant (P<0.05) differences were found among the drug release profile from different level of polymeric matrices. The release mechanism changed from non-fickian (n=0.489 for F-1) to fickian (n=0.439 and 0.429 for F-2, and F-3 respectively) as a function of decreasing the polymer concentration. The Mean Dissolution Time (MDT) values were increased with the increase in polymer concentration.

scholarly journals Comparison of Rheological, Drug Release, and Mucoadhesive Characteristics upon Storage between Hydrogels with Unmodified or Beta-Glycerophosphate-Crosslinked Chitosan

2018 ◽  
Vol 2018 ◽  
pp. 1-12 ◽  
Author(s):  
Emilia Szymańska ◽  
Anna Czajkowska-Kośnik ◽  
Katarzyna Winnicka
Keyword(s):  
Drug Release ◽  
Ex Vivo ◽  
Physicochemical Characteristics ◽  
Vaginal Mucosa ◽  
Drug Release Profile ◽  
Modified Chitosan ◽  
Long Term Storage ◽  
Crosslinked Chitosan ◽  
Chitosan Hydrogels ◽  
The Impact

The physicochemical characteristics of beta-glycerophosphate-crosslinked chitosan hydrogels were investigated upon long-term storage at ambient, accelerated, and refrigerated conditions and compared to unmodified chitosan formulations. Additionally, the impact of chitosan modification on the ex vivo mucoadhesive performance in contact with porcine vaginal mucosa and on the drug release profile from hydrogels was evaluated. Viscosity and mechanical properties of formulations with unmodified chitosan decreased significantly upon storage regardless of tested conditions as a result of hydrolytic depolymerization. Introduction of ion crosslinker exerted stabilizing effect on physicochemical performance of chitosan hydrogels but only upon storage at refrigerated conditions. Beta-glycerophosphate-modified chitosan formulations preserved organoleptic, rheological behavior, and hydrogel structure up to 3-month storage at 4 ± 2°C. Viscosity variations upon storage influenced markedly mucoadhesive properties and drug release rate from hydrogels.

scholarly journals Formulation and Evaluation of Sustained Release Matrix Tablet of Itopride

2021 ◽  
Vol 11 (5) ◽  
Keyword(s):  
Drug Release ◽  
Sustained Release ◽  
Ethyl Cellulose ◽  
Chemical Interaction ◽  
Research Work ◽  
Matrix Tablets ◽  
Crystalline Cellulose ◽  
Matrix Tablet ◽  
Natural Polymers ◽  
Drug Release Profile

The objective of this research work was to carry out design and evaluation of sustained release matrix tablets of Itopride by use of natural and synthetic polymers. Matrix tablets were prepared by wet granulation technique by using natural polymers like Carbopol 934, Tamarind poly saccharide, Locust bean gum, Ethyl cellulose, HPMC K 100 as matrix forming agent and excipients such as Lactose, Starch 1500, Magnesium stearate, MCC and talc were used. The dissolution medium consisted of 900 ml of 0.1 N HCl for first 2 hours and then 7.4 phosphate buffer for remaining 10 hours. The release of Itopride from matrix containing lactose, micro crystalline cellulose and starch 1500 as diluents. The drug release rate was found in order of lactose> micro crystalline cellulose>starch 1500. The formulation was optimized on the basis of acceptable tablet properties and in-vitro drug release. The release data were fit into different kinetic models (zero-order, first- order, Higuchi’s equation and Korsmeyer-Peppas equation). Optimized formulation was tested for their compatibility with Itopride by FT-IR studies, which revealed that there is no chemical interaction occurred with polymer and other excipients. The drug release profile of the best formulation was well controlled and uniform throughout the dissolution studies. Keywords: Matrix tablets, Itopride, Carbopol 934, HPMC K 100, Ethyl cellulose.

scholarly journals Formulation and Evaluation of Colchicine Sustained release tablet by using factorial designs

2021 ◽  
Vol 11 (5-S) ◽  
pp. 100-107
Author(s):  
M. Pradeep Kumar ◽  
Goparaju Suryanarayana Murthy ◽  
Annamdasu Lakshmi Poojitha ◽  
P. Sindhuri ◽  
A Sreekanth ◽  
...  
Keyword(s):  
Drug Release ◽  
Ethyl Cellulose ◽  
Polymer Concentration ◽  
Release Profile ◽  
Drug Release Profile ◽  
In Vitro Drug Release ◽  
Similarity Factor ◽  
Time Required ◽  
Full Factorial

The study on the effect of polymer concentration on in vitro drug release profile revealed that there is a change in vitro drug release parameters (t50, t80, and MDT) with a change in polymer concentration. Fraction of HPMC K4M, HPMC K 100 M, and Ethyl Cellulose were required to be 15, 10, and 7 mg respectively for designing optimized batch F7. The release rate of Colchicine decreased proportionally with an increase in the concentration of ethyl Cellulose and HPMC K100 M. Also the high amount of HPMC K4M leads to the less initial release and sustain effect. A theoretical drug release profile was generated using pharmacokinetic parameters of Colchicine. The value of t50 and t80 of theoretical drug release profile was found to be 242 min and 529 min respectively. The similarity factor f2 was applied between the in vitro drug release profile of optimizing batches and theoretical profile, which indicate a decent similarity between all in vitro drug release profiles (f2 = 68.28 for F7). All the batches except F1shows the value of f2 value within a range. Batch F7 showed the highest f2 (f2 = 68.28) among all the batches and this similarity was also reflected in t50 (≈ 256 min) and t80 (≈ 554 min) values. A 23 full factorial design was applied to systemically optimize in vitro drug release profile. The HPMC K4M (X1), Concentration of HPMC K100 M (X2), and concentration of EC (X3) were selected as independent variables. The time required for 50% drug released (t50), the time required for 80% drug release (t80), similarity factor f2, and mean dissolution time (MDT) were selected as dependent variables. The results of full factorial design indicate that the HPMC K4M (X1), Concentration of HPMC K100 M (X2), and concentration of EC (X3) have a significant effect on in vitro drug release profile. To find out the release mechanism the in vitro release data were fitted in the Korsmeyer-Peppas equation. All Batches except F1 and F3 show Anomalous diffusion-controlled release (combined mechanism of diffusion and case II transport).  

Sign in / Sign up

Export Citation Format

Share Document