scholarly journals Experimental Evaluation of Erosion of Gunmetal under Asymmetrical Shaped Sand Particle

2015 ◽  
Vol 2015 ◽  
pp. 1-31 ◽  
Author(s):  
Mohammad Asaduzzaman Chowdhury ◽  
Uttam Kumar Debnath ◽  
Dewan Muhammad Nuruzzaman ◽  
Md. Monirul Islam
Keyword(s):  
Impact Velocity ◽  
Wear Behavior ◽  
Maximum Level ◽  
Impact Angle ◽  
Operating Conditions ◽  
Silica Sand ◽  
Sand Particle ◽  
Damage Propagation ◽  
Erosion Efficiency ◽  
The Impact

The erosion characteristics of gunmetal have been evaluated practically at different operating conditions. Asymmetrical silica sand (SiO2) is taken into account as erodent within range of 300–600 μm. The impact velocity within 30–50 m/sec, impact angle 15–900, and stand off distance 15–25 mm are inspected as other relevant operating test conditions. The maximum level of erosion is obtained at impact angle 15° which indicates the ductile manner of the tested gunmetal. The higher the impact velocity, the higher the erosion rate as almost linear fashion is observed. Mass loss of gunmetal reduces with the increase of stand-off distance. A dimensional analysis, erosion efficiency (η), and relationship between friction and erosion indicate the prominent correlation. The test results are designated using Taguchi’s and ANOVA concept.S/Nratio indicates that there are 1.72% deviations that are estimated between predicted and experimental results. To elaborately analyze the results, ANN and GMDH methods are mentioned. After erosion process of tested composite, the damage propagation on surfaces is examined using SEM for the confirmation of possible nature of wear behavior. The elemental composition of eroded test samples at varying percentage of gunmetal is analyzed by EDX analysis.

Experimental analysis of aluminum alloy under solid particle erosion process

2016 ◽  
Vol 230 (12) ◽  
pp. 1516-1541 ◽  
Author(s):  
Mohammad A Chowdhury ◽  
Uttam K Debnath ◽  
Dewan M Nuruzzaman ◽  
Md. Monirul Islam
Keyword(s):  
Aluminum Alloy ◽  
Impact Velocity ◽  
Operating Parameter ◽  
Maximum Level ◽  
Impact Angle ◽  
Silica Sand ◽  
Erosion Process ◽  
Damage Propagation ◽  
Erosion Efficiency ◽  
The Impact

The erosion behaviors of aluminum alloy have been evaluated practically at different test conditions under ambient temperature. Irregular silica sand (SiO2) is used as an erodent within the range of 300–600 µm. The impact velocity within 30–50 m/s, impact angle 15–90°, and stand-off distance 15–25 mm considered as related parameters. The maximum level of erosion is obtained at impact angle 15° which indicates the ductile manner of the tested alloy. The higher the impact velocity, the higher the erosion rate as almost linear fashion is observed. Mass loss of aluminum alloy reduces with the increase of stand-off distance. A dimensional analysis, erosion efficiency (η) and relationship between friction and erosion indicate the prominent correlation. The test results are designated using Taguchi’s concept to ensure the minimization of observations for clarification of results in alternative process. ANOVA data analysis is considered to signify the interaction of tested parameters as well as identifying most influencing operating parameter. S/N ratio indicates that there are 2.92% deviations estimated between predicted and experimental results. To elaborately analyze the results, GMDH method is mentioned. After erosion process of the tested composite, the damage propagation on the surfaces is examined using SEM for confirming wear mechanisms. The elemental composition of eroded test samples at varying percentage of aluminum is analyzed by energy dispersive X-ray spectroscopy analysis.

Friction and wear behaviors of sand particle against casing steel

2018 ◽  
Vol 233 (3) ◽  
pp. 393-405
Author(s):  
Liu Yang ◽  
Deguo Wang ◽  
Yanbao Guo ◽  
Shuhai Liu
Keyword(s):  
Abrasive Wear ◽  
Friction And Wear ◽  
Oil And Gas ◽  
Wear Behavior ◽  
Processing Condition ◽  
Friction Model ◽  
Real Contact Area ◽  
Sand Particle ◽  
Friction Resistance ◽  
The Impact

Tools abrasive wear due to sand particles has caused severe damage during oil and gas exploitation. The friction and wear behaviors of single quartz sand particle against N80 casing steel were investigated to estimate the particle transport resistance and particle abrasive wear behavior using a homemade tribometer in wellbore sand cleanout. Various measurements were conducted to research the impact factor of particle under different water processing condition, dry, short immersion, wet, influences of load and slide velocity. Experimental results indicated that particle-casing friction resistance is mainly formed due to plowing and adhesion effect. Casing transfer and plowing removal are two main damage forms. Particle real contact area increases noticeably after water absorption, which decreases the hertz contact stress and finally produces less plowing depth of casing steel and causes less damage. With load increasing, friction resistance and wear increase with addition of plowing depth. A simple particle-casing friction model was established considering the experimental contact behavior.

Stepwise Erosion as a Method for Investigating the Wear Mechanisms at Different Impact Angles in Slurry Erosion

2014 ◽  
Vol 136 (2) ◽  
Author(s):  
Y. M. Abd-Elrhman ◽  
A. Abouel-Kasem ◽  
S. M. Ahmed ◽  
K. M. Emara
Keyword(s):  
Rebound Effect ◽  
Impact Angle ◽  
Silica Sand ◽  
Slurry Erosion ◽  
Nominal Size ◽  
Erosion Mechanisms ◽  
Impact Angles ◽  
The Impact ◽  
Calculated Number ◽  
Number Of Particles

In the present work, stepwise erosion technique was carried out to investigate in detail the influence of impact angle on the erosion process of AISI 5117 steel. The number of impact sites and their morphologies at different impact angles were investigated using scanning electron microscope (SEM) examination and image analysis. The tests were carried out with particle concentration of 1 wt. %, and the impact velocity of slurry stream was 15 m/s. Silica sand—which has a nominal size range of 250–355 μm—was used as an erodent, using whirling-arm test rig. The results have shown that the number of craters, as expected, increases with the increase in the mass of erodent for all impact angles and this number decreases with the increase of the impact angle. In addition, the counted number of craters is larger than the calculated number of particles at any stage for all impact angles. This may be explained by the effect of the rebound effect of particles, the irregular shape for these particles, and particle fragmentation. The effect of impact angle based on the impact crater shape can be divided into two regions; the first region for θ ≤ 60 deg and the second region for θ ≥ 75 deg. The shape of the craters is related to the dominant erosion mechanisms of plowing and microcutting in the first region and indentation and lip extrusion in the second region. In the first region, the length of the tracks decreases with the increase of impact angle. The calculated size ranges are from few micrometers to 100 μm for the first region and to 50 μm in the second region. Chipping of the former impact sites by subsequent impact particles plays an important role in developing erosion.

Numerical Analysis of Wavy Interface Formation and Successive Temperature Change in Magnetic Pulse Welded Al/Cu Joint

2016 ◽  
Vol 877 ◽  
pp. 655-661 ◽  
Author(s):  
Junto Nishiwaki ◽  
Takashi Kambe ◽  
Yasutaka Kedo ◽  
Yohei Harada ◽  
Shinji Muraishi ◽  
...  
Keyword(s):  
Impact Velocity ◽  
Intermediate Layer ◽  
Impact Angle ◽  
Joint Interface ◽  
Dissimilar Metals ◽  
Magnetic Pulse ◽  
Flyer Plate ◽  
Interface Formation ◽  
Wavy Interface ◽  
The Impact

Magnetic pulse welding (MPW) which is one of the impact welding methods is suitable for a wide variety of combinations of similar and dissimilar metals. The flyer plate is accelerated by electromagnetic force and collided to the parent plate. A characteristic wavy interface is formed. The impact velocity and impact angle of the flyer plate during impact are important parameters which affect the interface morphology. In the case of dissimilar metals (e.g. Al/Cu, Al/Fe), the intermediate layer (such as intermetallic compound (IMC)) is formed by wavy interface formation and local temperature increase. The intermediate layer often decreases the bonding strength. Wavy interface formation mechanism and temperature increase at the joint interface should be investigated in order to obtain the dissimilar metal joint with high bonding strength. In this study, the impact velocity and impact angle of the flyer plate were obtained by using ANSYS Emag-Mechanical. Based on the obtained impact velocity and impact angle of the flyer plate in the MPW, the wavy interface formation and temperature change were reproduced by using ANSYS Autodyn for solving non-liner dynamics problems. Al sheets and Cu sheets were joined by the MPW. The joint interface was observed by OM and SEM and compared to the simulation result.

Study on Erosion Wear Property of Nickel-Chromium Cast Iron

2013 ◽  
Vol 575-576 ◽  
pp. 535-538
Author(s):  
Jing Pei Xie ◽  
Li Jun Zhang ◽  
Ai Qin Wang ◽  
Xing Hai Shao
Keyword(s):  
Cast Iron ◽  
Wear Behavior ◽  
Strong Acid ◽  
Impact Angle ◽  
Homogeneous Distribution ◽  
Test Machine ◽  
Wear Property ◽  
Erosion Wear ◽  
The Matrix ◽  
The Impact

The influences of the impact angle and the corrosive agent acidity on low-chromium and nickel contained cast iron were studied in the behavior of erosion wear. The wear rule was summarized and the mechanics of the erosion wear behavior were analyzed in this thesis. Erosion wear experiments were carried on MCF-30 erosion test machine, and then the structure and surface morphology of the samples were analyzed by Scanning Electron Microscopy (SEM). The results showed that the alloy carbide (Fe, Cr)3C was generated by a kind of reticulate distribution in the matrix after oil quench at 960°C and temper at 250°C. The continuous and homogeneous distribution, just like the skeleton of the material, enhanced the wear resistance. The shape of erosion wear curve was M at different impact angles. The biggest wear rate occurred at a 60-degree impact angle. The erosion wear property was greatly affected by the strong acid, but it can be ignored when pH3.

A Procedure to Predict Solid Particle Erosion in Elbows and Tees

1995 ◽  
Vol 117 (1) ◽  
pp. 45-52 ◽  
Author(s):  
S. A. Shirazi ◽  
J. R. Shadley ◽  
B. S. McLaury ◽  
E. F. Rybicki
Keyword(s):  
Experimental Data ◽  
Impact Velocity ◽  
Erosion Rate ◽  
Operating Conditions ◽  
Fluid Viscosity ◽  
Erosion Rates ◽  
Sand Particles ◽  
Liquid Flows ◽  
The Impact ◽  
Sand Size

A semi-empirical procedure has been developed for predicting erosion rates in pipe geometries, such as elbows and tees. The procedure can be used to estimate safe operating conditions and velocities in oil and gas production where sand is present. In the proposed procedure, a concept is introduced that allows determination of erosion rate for different pipe geometries. In the procedure, based on empirical observations, the erosion rate is related to the impact velocity of sand particles on a pipe fitting wall. A simplified particle tracking model is developed and is used to estimate the impact velocity of sand particles moving in a stagnation region near the pipe wall. A new concept of equivalent stagnation length allows the simplified procedure to be applicable to actual pipe geometries. The “equivalent stagnation regions” of an elbow and a tee geometry of different sizes are obtained from experimental data for small pipe diameters, and a computational model is used to extend the procedure to larger pipe diameters. Currently, the prediction method applies to mild steel and accounts for the effects of sand size, shape, and density; fluid density, viscosity, and flow speed; and pipe size and shape. The proposed method has been verified for gas and liquid flows through several comparisons with experimental data reported in the literature. The results of the model accurately predict the effects of sand size and fluid viscosity observed in the experiments. Furthermore, predicted erosion rates showed good agreement with experimental data for gas, liquid, and gas-liquid flows in several 50.8-mm (2-in.) elbows and tees.

scholarly journals An Influence of Factors of Flow Condition, Particle and Material Properties on Slurry Erosion Resistance

2019 ◽  
Vol 19 (2) ◽  
pp. 28-53 ◽  
Author(s):  
M. H. Buszko ◽  
A. K. Krella
Keyword(s):  
Material Properties ◽  
Erosion Resistance ◽  
Synergistic Effects ◽  
Impact Angle ◽  
Operating Conditions ◽  
Slurry Erosion ◽  
Particle Properties ◽  
Different Types ◽  
Degradation Of Materials ◽  
The Impact

AbstractThe degradation of materials due to slurry erosion is the serious problem which occurs in the power industries. The paper presents actual knowledge about an influence of individual factors connected with flow conditions, particles and material properties on the slurry erosion resistance. Among the factors connected with operating conditions, an influence of impact angle, and velocity of impact, particle concertation and liquid temperature have been described. In case of the factors connected with solid particle properties, an influence of the size, shape and hardness have been discussed. In the part devoted to the impact of material properties, due to different types of materials, the issues of resistance to erosion of slurries related to the properties of steel, ceramics and polymers are discussed separately. In the paper has been shown that a change of any of mentioned factors causes a change in the erosion rate due to the synergistic effects that accompany to slurry degradation.

A Study on Slurry Erosion Behavior of High Chromium White Cast Iron

2017 ◽  
Vol 139 (4) ◽  
Author(s):  
M. A. Al-Bukhaiti ◽  
A. Abouel-Kasem ◽  
K. M. Emara ◽  
S. M. Ahmed
Keyword(s):  
Impact Velocity ◽  
Erosion Resistance ◽  
Normal Incidence ◽  
Impact Angle ◽  
Silica Sand ◽  
Slurry Erosion ◽  
High Chromium ◽  
Nominal Size ◽  
Plastic Indentation ◽  
Erosion Mechanisms

High chromium white irons (HCCIs) are used extensively throughout the mineral processing industry to handle erosive and corrosive slurries. This study is an investigation of the effect of impact angle and velocity on slurry erosion of HCCI. The tests were carried out using a rotating whirling-arm rig with particle concentration of 1 wt. %. Silica sand which has a nominal size range of 500–710 μm was used as an erodent. The results were obtained for angles of 30 deg, 45 deg, 60 deg, and 90 deg to the exposed surface and velocities of 5, 10, and 15 m/s. The highest erosion resistance of HCCI was at normal impact and the lowest at an angle of 30 deg, irrespective of velocity. The low erosion resistance at an oblique angle is due to large material removal by microcutting from ductile matrix and gross removal of carbides. The effect of velocity, over the studied range from 5 m/s to 15 m/s, on the increase in the erosion rate was minor. The change of impact velocity resulted in changing the slurry erosion mechanisms. At normal incidence, plastic indentation with extruded material of the ductile matrix was the dominant erosion mechanism at low impact velocity (5 m/s). With increasing impact velocity, the material was removed by the indentation of the ductile matrix and to smaller extent of carbide fracture. However, at high impact velocity (15 m/s), gross fracture and cracking of the carbides besides plastic indentation of the ductile matrix were the dominant erosion mechanisms.

Erosion and its Effect on a Water-Cooled Turbine

1978 ◽  
Author(s):  
Max Freedman
Keyword(s):  
Impact Velocity ◽  
Gas Turbines ◽  
Mass Loss Rate ◽  
Impact Angle ◽  
Aluminum Specimen ◽  
High Impact Velocity ◽  
Short Time ◽  
Impact Angles ◽  
The Impact

Erosion tests were run to obtain data for designing a water-cooled gas turbine collection shroud. All tests utilized a coherent stream of water ejected from a static nozzle against stationary small block specimens. Twenty-one tests were run with aluminum specimens and 16 more tests with other materials. The impact velocity was varied from 165 to 270 m/s (540 to 890 fps). The impact angle was varied from 10 to 90 deg. The mass loss rate results generally show four erosion regions, which are consistent with the literature. A correlation between regions two and four was found. Aluminum specimen erosion rate was found to be unexpectedly high with impact angles of 10 deg and moderate-to-high impact velocity. No report of previous liquid erosion work at impact angles less than 30 deg was found; since it is expected that water-cooled gas turbines will operate at impact angles of about 15 deg, erosion in this low impact angle region should be studied. If the correlation between erosion regions two and four can be quantized, then very short-time tests could be used to predict long-term erosion at minimal cost.

Evaluating Impact Properties of Cement Clinker at Different Angle for Impact Indentation

2011 ◽  
Vol 492 ◽  
pp. 43-46
Author(s):  
Xiu Fang Wang ◽  
Yi Wang Bao ◽  
Yan Qiu ◽  
Xiao Gen Liu ◽  
Yuan Tian
Keyword(s):  
Impact Velocity ◽  
Impact Force ◽  
Surface Damage ◽  
Impact Angle ◽  
Cement Clinker ◽  
Damage Degree ◽  
Indentation Tests ◽  
Impact Angles ◽  
The Impact ◽  
Peak Impact Force

Spherical impact indentation tests with different impact angles (90°, 60°, 45°, and 30°) was carried out to understand the effect of impact angles on damage degree of cement clinker. A linear rail which can adjust angle to alter impact velocity was used to guide the slipping impact head to impact the sample. The different steel wedge was used to change the impact angle. It is found that the area of damage surface for cement clinker is most serious the peak impact force for surface damage decreases but the contact indentation becomes longer with decreasing impact angle when the impact angle is 45°. Under almost the same impact velocity, the smaller the impact angle, the higher the impulse, the longer contact time, and the peak impact force of 45° is maximum.

Sign in / Sign up

Export Citation Format

Share Document