scholarly journals Mechanical Performance versus Corrosion Damage Indicators for Corroded Steel Reinforcing Bars

2015 ◽  
Vol 2015 ◽  
pp. 1-19 ◽  
Author(s):  
Silvia Caprili ◽  
Jörg Moersch ◽  
Walter Salvatore
Keyword(s):  
Performance Indicators ◽  
Mechanical Performance ◽  
Low Cycle Fatigue ◽  
Corrosion Damage ◽  
Fatigue Tests ◽  
Cycle Fatigue ◽  
Reinforcing Bars ◽  
Steel Bar ◽  
Damage Indicators ◽  
Current Standards

The experimental results of a testing campaign including tensile and low-cycle fatigue tests on different reinforcing steel bar types in the as-delivered and corroded condition are presented. Experimental data were statistically analyzed adopting ANOVA technique; Performance Indicators (PIs), describing the mechanical performance characteristics of reinforcements, and Corrosion Damage Indicators (CDIs), describing the detrimental effects of corrosion phenomena, were determined and correlated in order to evaluate the influence of corrosion on the behaviour of reinforcing steels, providing useful information for designers in addition to what is presented in current standards.

Effect of Alloying Elements on Mechanical Properties for A356 Casting Alloy

2007 ◽  
Vol 26-28 ◽  
pp. 111-114
Author(s):  
Chang Yeol Jeong ◽  
Chang Seog Kang ◽  
Jae Ik Cho
Keyword(s):  
Mechanical Performance ◽  
Low Cycle Fatigue ◽  
Fatigue Behavior ◽  
Eutectic Silicon ◽  
Magnesium Content ◽  
Eutectic Structure ◽  
Fatigue Tests ◽  
Cycle Fatigue ◽  
Experimental Conditions ◽  
Dendritic Arm Spacing

A quantitative study of the interactions between microstructural features such as secondary dendrite arm spacing (DAS), eutectic structure and fatigue behavior of two Al-Si-Mg casting alloys with silicon contents of 7% and 10% respectively, has been conducted. In the condition of minimizing casting defects, the influence of microstructural features on the mechanical performance becomes more pronounced. Depending on the magnesium content affecting the strength of the matrix, the tensile properties were changed upon experimental conditions; the tensile strength was increased with magnesium content, whereas the elongation was increased in the reverse case. The increase of both of high cycle fatigue and low cycle fatigue lives with decreasing the secondary dendritic arm spacing is observed, mainly due to homogeneous deformation owing to the fine size of eutectic silicon and Fe intermetallic particles. The fatigue dynamometer of a diesel cylinder head shows the same tendency with the results of specimen fatigue tests with microstructures.

Seismic resistance prediction of corroded S400 (BSt420) reinforcing bars

2018 ◽  
Vol 9 (1) ◽  
pp. 119-138
Author(s):  
Charis Apostolopoulos ◽  
George Konstantopoulos ◽  
Konstantinos Koulouris
Keyword(s):  
Seismic Behavior ◽  
Structural Integrity ◽  
Mechanical Performance ◽  
Low Cycle Fatigue ◽  
Seismic Loads ◽  
Reinforcing Bars ◽  
Content Type ◽  
The Past ◽  
Steel Bar ◽  
Resistance Prediction

Purpose Structures in seismic areas, during their service lifetime, are subjected to numerous seismic loads that certainly affect their structural integrity. The degradation of these structures, to a great extent, depends on the scale of seismic events, the steel mechanical performance on reversal loads and its resistance to corrosion phenomena. The paper aims to discuss these issues. Design/methodology/approach Based on the experimental results of seismic steel behavior S400 (BSt III), which was widely used in the past years, a prediction study of seismic steel behavior was conducted in the current study. This prediction on behavior of both reference and corroded steel was succeeded through a simulation of experimental low cycle fatigue conditions (LCF – strain controlled). Findings At the same time, the present study analyses fatigue factors (ef, a, fSR, ed, ep, R, b) that define their inelastic relation between tension – strain and a prediction model on behavior of both reference and corroded steel rebar, in seismic loads conditions (LCF), is proposed. Originality/value Moreover, this study dealt with the synergy of corrosion factor and the existence of superficial ribs (ribbed and smoothed) in seismic behavior of steel bar S400 (BSt420). The S-N curves that are exported can be resulted in a first attempt of prediction of anti-seismic behavior on reinforced concrete structures with this the same steel class.

Mechanical Characterization and Modeling of Direct Metal Laser Sintered Stainless Steel GP1

2019 ◽  
Vol 141 (3) ◽  
Author(s):  
Sanna F. Siddiqui ◽  
Abiodun A. Fasoro ◽  
Calvin Cole ◽  
Ali P. Gordon
Keyword(s):  
Stainless Steel ◽  
Mechanical Performance ◽  
Low Cycle Fatigue ◽  
Constitutive Models ◽  
Fatigue Tests ◽  
Material Behavior ◽  
Layer By Layer ◽  
Cycle Fatigue ◽  
Layer Deposition ◽  
Experimental Findings

The additive manufacturing (AM) process is unique in that it can facilitate anisotropy because of the layer-by-layer deposition technique intrinsic to this process. In order to develop a component for a desired application, it is necessary to understand the mechanics that facilitate this material behavior. This study investigates how build orientation affects the mechanical performance of as-built direct metal laser sintered (DMLS) stainless steel (SS) GP1 (also referred to as 17-4PH) through strain-controlled monotonic tension and completely reversed low-cycle fatigue (LCF) testing. The anisotropic behavior of DMLS SS GP1 is assessed for samples built along the horizontal plane. Fracture surfaces were found to exhibit ductile responses that were consistent with the σ–ε curves. Constitutive models (i.e., Ramberg–Osgood, Hahn) based upon linear elasticity and nonlinear plasticity are presented and used to simulate the monotonic discontinuous stress–strain yielding response of this material, which are found to be in agreement with the experimental data. A collection of low-cycle fatigue tests reveals initial strain hardening to stabilization, followed by softening to fracture. Tensile and fatigue material constants determined from experimental findings are also presented in this study. Plasticity effects on the life of varying build orientations are explored.

scholarly journals Fatigue Testing of Wearable Sensing Technologies: Issues and Opportunities

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4070
Author(s):  
Andrea Karen Persons ◽  
John E. Ball ◽  
Charles Freeman ◽  
David M. Macias ◽  
Chartrisa LaShan Simpson ◽  
...  
Keyword(s):  
Fatigue Life ◽  
Prediction Models ◽  
Fatigue Testing ◽  
Low Cycle Fatigue ◽  
Wearable Sensors ◽  
Fatigue Tests ◽  
Proof Of Concept ◽  
Cycle Fatigue ◽  
Wearable Sensing ◽  
Failure Data

Standards for the fatigue testing of wearable sensing technologies are lacking. The majority of published fatigue tests for wearable sensors are performed on proof-of-concept stretch sensors fabricated from a variety of materials. Due to their flexibility and stretchability, polymers are often used in the fabrication of wearable sensors. Other materials, including textiles, carbon nanotubes, graphene, and conductive metals or inks, may be used in conjunction with polymers to fabricate wearable sensors. Depending on the combination of the materials used, the fatigue behaviors of wearable sensors can vary. Additionally, fatigue testing methodologies for the sensors also vary, with most tests focusing only on the low-cycle fatigue (LCF) regime, and few sensors are cycled until failure or runout are achieved. Fatigue life predictions of wearable sensors are also lacking. These issues make direct comparisons of wearable sensors difficult. To facilitate direct comparisons of wearable sensors and to move proof-of-concept sensors from “bench to bedside,” fatigue testing standards should be established. Further, both high-cycle fatigue (HCF) and failure data are needed to determine the appropriateness in the use, modification, development, and validation of fatigue life prediction models and to further the understanding of how cracks initiate and propagate in wearable sensing technologies.

Cumulative acoustic emission energy for damage detection in composites reinforced by carbon fibers within low-cycle fatigue regime at various displacement amplitudes and rates

2021 ◽  
pp. 096739112098570
Author(s):  
Mohammad Azadi ◽  
Mohsen Alizadeh ◽  
Seyed Mohammad Jafari ◽  
Amin Farrokhabadi
Keyword(s):  
Acoustic Emission ◽  
Carbon Fibers ◽  
Polymer Matrix Composites ◽  
Low Cycle Fatigue ◽  
Energy Parameter ◽  
Fatigue Tests ◽  
Matrix Cracking ◽  
Matrix Composites ◽  
Cycle Fatigue ◽  
Cumulative Energy

In the present article, acoustic emission signals were utilized to predict the damage in polymer matrix composites, reinforced by carbon fibers, in the low-cycle fatigue regime. Displacement-controlled fatigue tests were performed on open-hole samples, under different conditions, at various displacement amplitudes of 5.5, 6.0, 6.5 and 7.0 mm and also under various displacement rates of 25, 50, 100 and 200 mm/min. After acquiring acoustic emission signals during cycles, two characteristic parameters were used, including the energy and the cumulative energy. Obtained results implied that the energy parameter of acoustic emission signals could be used only for the macroscopic damage, occurring at more than 65% of normalized fatigue cycles under different test conditions. However, the cumulative energy could properly predict both microscopic and macroscopic defects, at least two failure types, including matrix cracking at first cycles and the fiber breakage at last cycles. Besides, scanning electron microscopy images proved initially such claims under all loading conditions.

Evaluation of the Heat Treatment Role for Light Aluminum Alloys Subjected to Creep and Low Cycle Fatigue

2010 ◽  
Vol 638-642 ◽  
pp. 455-460 ◽  
Author(s):  
A. Rutecka ◽  
L. Dietrich ◽  
Zbigniew L. Kowalewski
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Low Cycle Fatigue ◽  
Numerical Models ◽  
Cyclic Hardening ◽  
Fatigue Tests ◽  
Cycle Fatigue ◽  
Lower Stress ◽  
Creep Tests ◽  
Different Temperatures

The AlSi8Cu3 and AlSi7MgCu0.5 cast aluminium alloys of different composition and heat treatment were investigated to verify their applicability as cylinder heads in the car engines [1]. Creep tests under the step-increased stresses at different temperatures, and low cycle fatigue (LCF) tests for a range of strain amplitudes and temperatures were carried out. The results exhibit a significant influence of the heat treatment on the mechanical properties of the AlSi8Cu3 and AlSi7MgCu0.5. An interesting fact is that the properties strongly depend on the type of quenching. Lower creep resistance (higher strain rates) and lower stress response during fatigue tests were observed for the air quenched materials in comparison to those in the water quenched. Cyclic hardening/softening were also observed during the LCF tests due to the heat treatment applied. The mechanical properties determined during the tests can be used to identify new constitutive equations and to verify existing numerical models.

Effect of Different Welded Structures on Mechanical Properties of TA2 Tube-to-Tubesheet Joints

2014 ◽  
Vol 136 (4) ◽  
Author(s):  
Xinlong Wei ◽  
Yang Qian ◽  
Junhui Wang ◽  
Jianxin Zhou ◽  
Xiang Ling
Keyword(s):  
Applied Load ◽  
Low Cycle Fatigue ◽  
Weld Zone ◽  
Steel Tube ◽  
Fatigue Tests ◽  
Cycle Fatigue ◽  
Welded Structures ◽  
Pull Out ◽  
Weld Toe ◽  
Welded Tube

Four types of TA2 welded tube-to-tubesheet joints prepared by manual tungsten arc argon-shielded welding technique are studied in this paper. The pull-out tests and low cycle fatigue tests were performed to optimize welded structures of tube and tubesheet. The results show that fractures of welded TA2 tube and tubesheet samples occur at weld zone of TA2 steel tube for the pull-out tests and low cycle fatigue tests. The extension-tubesheet welded joints have the maximum pull-out forces and the best fatigue resistance, and the internal-bore welded joint with 45 deg bevel occupies second place. Fractures are both initiated from weld toe of the outside of tube for the pull-out tests and low cycle fatigue tests. Crack propagates along the direction of 45 deg for the pull-out test. However, crack propagates perpendicularly to the direction of the applied load for low cycle fatigue test, and then fractures immediately parallel to the direction of the applied load. Fatigue striations with a spacing of about 10 μm can be observed on the fatigue crack propagation zone. However, hemispheroidal dimples exist on instant rupture zone.

Damage in Adhesive Joints During Low Cycle Fatigue

2010 ◽  
Author(s):  
Iva´n C. Ca´bulo-Pe´rez ◽  
Juan P. Casas-Rodri´guez
Keyword(s):  
Plastic Strain ◽  
Low Cycle Fatigue ◽  
Stress Test ◽  
Damage Model ◽  
Fatigue Tests ◽  
Constant Stress ◽  
Cycle Fatigue ◽  
Damage Behavior ◽  
Non Linear ◽  
Compressive Loads

The objective of this research is to study the damage behavior of bulk adhesive and single lap joint (SLJ) specimens during low cycle fatigue (LCF). Fatigue tests under constant stress amplitude were done and strain response was measured through cycles to failure using the bulk adhesive and SLJ data. A non linear damage model was used to fit experimental results. Identification of the damage parameters for bulk adhesive was obtained from the damage against accumulated plastic strain plot. It is shown that the plastic strain can be obtained from the constant stress test if the instantaneous elastic modulus, i.e. modulus affected by damage, is evaluated for each cycle. On the other hand, damage in SLJ was seen mainly in the adhesive for itself — no substrate failure — this fact is used to propose that fatigue response in the joint is due to continuum damage accumulation in the adhesive as the number of cycles increases. Damage behavior under compressive loads was not taken into account but good correlation of numerical and experimental data was obtained. It was found that damage evolution behaves in a non linear manner as the plastic deformation grows for each cycle: on fatigue onset an accelerated damage grow is observed, then a proportional evolution, and finally a rapid failure occurs; this characteristics were seen in both the SLJ and bulk adhesive specimen. So far, this research takes the damage model found in a standard adhesive specimen and assumes it is accurate enough to represent the damage behavior of the SLJ configuration.

scholarly journals Impact of Temperature on Low-Cycle Fatigue Characteristics of the HR6W Alloy

Materials ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 6741
Author(s):  
Grzegorz Junak ◽  
Anżelina Marek ◽  
Michał Paduchowicz
Keyword(s):  
Fatigue Life ◽  
Room Temperature ◽  
Low Cycle Fatigue ◽  
Fatigue Tests ◽  
Total Strain ◽  
Cycle Fatigue ◽  
Fatigue Characteristics

This paper presents the results of tests conducted on the HR6W (23Cr-45Ni-6W-Nb-Ti-B) alloy under low-cycle fatigue at room temperature and at 650 °C. Fatigue tests were carried out at constant values of the total strain ranges. The alloy under low-cycle fatigue showed cyclic strengthening both at room temperature and at 650 °C. The degree of HR6W strengthening described by coefficient n’ was higher at higher temperatures. At the same time, its fatigue life Nf at room temperature was, depending on the range of total strain adopted in the tests, several times higher than observed at 650 °C.

Sign in / Sign up

Export Citation Format

Share Document