scholarly journals Designing of Collagen Based Poly(3-hydroxybutyrate-co-4-hydroxybutyrate) Scaffolds for Tissue Engineering

2015 ◽  
Vol 2015 ◽  
pp. 1-10 ◽  
Author(s):  
S. Vigneswari ◽  
H. P. S. Abdul Khalil ◽  
A. A. Amirul
Keyword(s):  
Molar Fraction ◽  
Fibroblast Cell ◽  
Solvent System ◽  
Optimal Level ◽  
Collagen Concentration ◽  
Water Contact ◽  
Angle Measurements ◽  
Contact Angle Measurements ◽  
Organic Elemental Analysis ◽  
Scanning Electron

P(3HB-co-4HB) copolymer was modified using collagen by adapting dual solvent system. The surface properties of samples were characterized by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), organic elemental analysis (CHN analysis), and water contact angle measurements. The effects of collagen concentration, scaffold thickness, and 4HB molar fraction on the hydrophilicity were optimized by the Taguchi method. The orthogonal array experiment was conducted to obtain the response for a hydrophilic scaffold. Analysis of variance (ANOVA) was used to determine the significant parameters and determine the optimal level for each parameter. The results also showed that the hydrophilicity of P(3HB-co-4HB)/collagen blend scaffolds increased as the collagen concentration increased up to 15 wt% with a molar fraction of 50 mol% at 0.1 mm scaffold thickness. The biocompatibility of the P(3HB-co-4HB)/collagen blend surface was evaluated by fibroblast cell (L929) culture. The collagen blend scaffold surfaces showed significant cell adhesion and growth as compared to P(3HB-co-4HB) copolymer scaffolds.

Nanostructured Polymer Brushes With Reversibly Changing Properties

2002 ◽  
Vol 727 ◽  
Author(s):  
Denys Usov ◽  
Manfred Stamm ◽  
Sergiy Minko ◽  
Christian Froeck ◽  
Andreas Scholl ◽  
...  
Keyword(s):  
Polymer Brushes ◽  
Phase Segregation ◽  
Water Contact ◽  
Angle Measurements ◽  
Nanostructured Polymer ◽  
Contact Angle Measurements ◽  
Vertical Segregation ◽  
Oxygen Plasma Etching ◽  
Grafting From ◽  
Photoemission Electron

AbstractWe investigated the interplay between different mechanisms of the lateral and vertical segregation in the synthesized via “grafting from” approach symmetric A/B (where A and B are poly(styrene-co-2,3,4,5,6-pentafluorostyrene) and poly(methylmethacrylate), respectively) polymer brushes upon exposure to different solvents. We used X-ray photoemission electron spectroscopy and microscopy (X-PEEM), AFM, water contact angle measurements, and oxygen plasma etching to study morphology of the brushes. The ripple morphology after toluene (nonselective solvent) revealed elongated lamellar-like domains of A and B polymers alternating across the surface. The dimple-A morphology consisting of round clusters of the polymer A was observed after acetone (selective solvent for B). The top layer was enriched with the polymer B showing that the brush underwent both the lateral and vertical phase segregation. A qualitative agreement with predictions of SCF theory was found.

scholarly journals Epoxy/alumina composite coating on welded steel 316L with excellent wear and anticorrosion properties

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Maryama Hammi ◽  
Younes Ziat ◽  
Zakaryaa Zarhri ◽  
Charaf Laghlimi ◽  
Abdelaziz Moutcine
Keyword(s):  
Electrochemical Behaviour ◽  
Sem Analysis ◽  
Water Contact ◽  
Welded Steel ◽  
Melted Zone ◽  
Angle Measurements ◽  
Contact Angle Measurements ◽  
Alumina Composite ◽  
The Cost ◽  
Good Contrast

AbstractThe main purpose of this study is to elaborate anticorrosive coatings for the welded steel 316L, since this later is widely used in industrial field. Hence, within this work we have studied the electrochemical behaviour of different zones of the welded steel 316 in 1 M HCl media. The macrography study of the welded steel has revealed the different areas with a good contrast. We have stated three different zones, namely; melted zone (MZ), heat affected zone (HAZ) and base metal zone (BM). Impedance studies on welded steel 316L were conducted in 1 M HCl solution, coating of Epoxy/Alumina composite was applied on different zones, in order to reveal the anti-corrosion efficiency in each zone. Scanning electron microscopy (SEM) analysis was undertaken in order to check how far the used coating in such aggressive media protects the studied zones and these findings were assessed by water contact angle measurements. The choice of this coating is based on the cost and the safety. We concluded that the Epoxy/Alumina composite has a good protecting effect regarding welded steel in aggressive media.

scholarly journals PLA-Based Hybrid and Composite Electrospun Fibrous Scaffolds as Potential Materials for Tissue Engineering

2017 ◽  
Vol 2017 ◽  
pp. 1-11 ◽  
Author(s):  
Anna Magiera ◽  
Jarosław Markowski ◽  
Elzbieta Menaszek ◽  
Jan Pilch ◽  
Stanislaw Blazewicz
Keyword(s):  
Tissue Engineering ◽  
Mechanical Tests ◽  
Hybrid Structures ◽  
Poly Lactic Acid ◽  
Electrospinning Technique ◽  
Water Contact ◽  
Human Osteoblasts ◽  
Angle Measurements ◽  
Contact Angle Measurements ◽  
Normal Human

The aim of the study was to manufacture poly(lactic acid)- (PLA-) based nanofibrous nonwovens that were modified using two types of modifiers, namely, gelatin- (GEL-) based nanofibres and carbon nanotubes (CNT). Hybrid nonwovens consisting of PLA and GEL nanofibres (PLA/GEL), as well as CNT-modified PLA nanofibres with GEL nanofibres (PLA + CNT/GEL), in the form of mats, were manufactured using concurrent-electrospinning technique (co-ES). The ability of such hybrid structures as potential scaffolds for tissue engineering was studied. Both types of hybrid samples and one-component PLA and CNTs-modified PLA mats were investigated using scanning electron microscopy (SEM), water contact angle measurements, and biological and mechanical tests. The morphology, microstructure, and selected properties of the materials were analyzed. Biocompatibility and bioactivity in contact with normal human osteoblasts (NHOst) were studied. The coelectrospun PLA and GEL nanofibres retained their structures in hybrid samples. Both types of hybrid nonwovens were not cytotoxic and showed better osteoinductivity in comparison to scaffolds made from pure PLA. These samples also showed significantly reduced hydrophobicity compared to one-component PLA nonwovens. The CNT-contained PLA nanofibres improved mechanical properties of hybrid samples and such a 3D system appears to be interesting for potential application as a tissue engineering scaffold.

scholarly journals Surface Modification of the Alloy Ti-7.5Mo by Anodization for Biomedical Applications

2016 ◽  
Vol 869 ◽  
pp. 913-917 ◽  
Author(s):  
Ana Lucia do Amaral Escada ◽  
Javier Andres Muñoz Chaves ◽  
Ana Paula Rosifini Alves Claro
Keyword(s):  
Contact Angle ◽  
Electron Microscope ◽  
Biomedical Applications ◽  
Anatase Phase ◽  
Ammonium Fluoride ◽  
X Ray ◽  
Angle Measurements ◽  
Contact Angle Measurements ◽  
Simple Surface ◽  
Scanning Electron

The purpose of this study was to evaluate the TiO2 nanotubes growth and the variation in its diameter to improve the surface properties of Ti-7.5Mo to use for biomedical applications. For the nanotubes TiO2 growth, the samples were anodized in glycerol and ammonium fluoride and divided according to the anodizing potential at 5V to 10V and 24 hour time. The surfaces were examined by scanning electron microscope (SEM), X-ray analysis (XRD) and contact angle measurements. The average tube diameter, ranging in size from 13 to 23 nm, was found to increase with increasing anodizing voltage. It was also observed a decrease in contact angle in accordance with the increase in the anodizing potential. The X-ray analysis showed the presence of anatase phase in samples whose potential was 10V and this condition represents a simple surface treatment for Ti-7.5Mo alloy that has high potential for biomedical applications.

scholarly journals Synthesis, Hydrophilicity and Micellization of Coil–Brush Polystyrene-b-(polyglycidol-g-polyglycidol) Copolymer—Comparison with Linear Polystyrene-b-Polyglycidol

Polymers ◽  
2022 ◽  
Vol 14 (2) ◽  
pp. 253
Author(s):  
Mariusz Gadzinowski ◽  
Maciej Kasprów ◽  
Teresa Basinska ◽  
Stanislaw Slomkowski ◽  
Łukasz Otulakowski ◽  
...  
Keyword(s):  
Contact Angle ◽  
Self Assembly ◽  
Original Method ◽  
Critical Micellization Concentration ◽  
Water Contact ◽  
1H And 13C Nmr ◽  
Similar Composition ◽  
Angle Measurements ◽  
Contact Angle Measurements ◽  
Static Conditions

In this paper, an original method of synthesis of coil–brush amphiphilic polystyrene-b-(polyglycidol-g-polyglycidol) (PS-b-(PGL-g-PGL)) block copolymers was developed. The hypothesis that their hydrophilicity and micellization can be controlled by polyglycidol blocks architecture was verified. The research enabled comparison of behavior in water of PS-b-PGL copolymers and block–brush copolymers PS-b-(PGL-g-PGL) with similar composition. The coil–brush copolymers were composed of PS-b-PGL linear core with average DPn of polystyrene 29 and 13 of polyglycidol blocks. The DPn of polyglycidol side blocks of coil–b–brush copolymers were 2, 7, and 11, respectively. The copolymers were characterized by 1H and 13C NMR, GPC, and FTIR methods. The hydrophilicity of films from the linear and coil–brush copolymers was determined by water contact angle measurements in static conditions. The behavior of coil–brush copolymers in water and their critical micellization concentration (CMC) were determined by UV-VIS using 1,6-diphenylhexa-1,3,5-trien (DPH) as marker and by DLS. The CMC values for brush copolymers were much higher than for linear species with similar PGL content. The results of the copolymer film wettability and the copolymer self-assembly studies were related to fraction of hydrophilic polyglycidol. The CMC for both types of polymers increased exponentially with increasing content of polyglycidol.

How Electrophoretic Deposition with Ligand-Free Platinum Nanoparticles Affects Contact Angle

2015 ◽  
Vol 654 ◽  
pp. 218-223 ◽  
Author(s):  
Alexander Heinemann ◽  
Sven Koenen ◽  
Kerstin Schwabe ◽  
Christoph Rehbock ◽  
Stephan Barcikowski
Keyword(s):  
Contact Angle ◽  
Electrophoretic Deposition ◽  
Platinum Nanoparticles ◽  
Deposition Time ◽  
Deposition Process ◽  
Angle Measurements ◽  
Contact Angle Measurements ◽  
Ligand Free ◽  
Vital Parameters ◽  
Scanning Electron

Electrophoretic deposition of ligand-free platinum nanoparticles has been studied to elucidate how wettability, indicated by contact angle measurements, is linked to vital parameters of the electrophoretic deposition process. These parameters, namely the colloid concentration, electric field strength and deposition time, have been systematically varied in order to determine their influence on the contact angle. Additionally, scanning electron microscopy has been used to confirm the homogeneity of the achieved coatings.

scholarly journals Improved de-inking of inkjet-printed paper using environmentally friendly atmospheric pressure low temperature plasma for paper recycling

2019 ◽  
Vol 9 (1) ◽  
Author(s):  
Rodolphe Mauchauffé ◽  
Seung Jun Lee ◽  
Isaac Han ◽  
Sang Hyeong Kim ◽  
Se Youn Moon
Keyword(s):  
Plasma Treatment ◽  
Atmospheric Pressure ◽  
Paper Recycling ◽  
Temperature Plasma ◽  
Water Contact ◽  
Angle Measurements ◽  
Natural Energy ◽  
Contact Angle Measurements ◽  
Speed Up ◽  
Uv Visible

Abstract Nowadays, due to environmental pollution and natural energy consumption caused by waste paper, many researches are being conducted on the reuse of printed-paper. To recycle the paper, de-inking has to be performed. In this article, in order to reduce the use of the commonly used de-inking chemicals, the effect of an atmospheric pressure helium plasma treatment on the de-inking enhancement of printed-paper is studied. Through colorimeter and UV-visible spectrometer measurements the plasma treatment is shown to speed up the de-inking. While SEM observations and FTIR measurements suggest that the paper quality is retained upon plasma treatment, the increase of surface hydrophilicity measured by water contact angle measurements, compared to non-treated paper, is believed to enhance the fiber swelling of the paper and lead to a faster ink removal.

Non-woven Membranes Electrospun from Polylactic Acid Incorporating Silver Nanoparticles as Biocide

2012 ◽  
Vol 1376 ◽  
Author(s):  
Haydee Vargas-Villagran ◽  
Elvia Teran-Salgado ◽  
Maraolina Dominguez-Diaz ◽  
Osvaldo Flores ◽  
Bernardo Campillo ◽  
...  
Keyword(s):  
Contact Angle ◽  
Silver Nanoparticles ◽  
Polylactic Acid ◽  
Chloroform Solution ◽  
Average Diameter ◽  
Electrospinning Process ◽  
Water Contact ◽  
X Ray Scattering ◽  
Angle Measurements ◽  
Contact Angle Measurements

ABSTRACTIn this research, we describe the electrospinning processing of polylactic acid (PLA) and the influence of silver nanoparticles on the morphology and microstructure of produced non woven membranes thus produced. The PLA was electrospun from a chloroform solution and a filamentary and granular morphology was obtained, the filaments having an average diameter of 1.25 μm, When silver nanoparticles (of ca. 12 nm size) were incorporated, the filaments diameter was reduced to an average of 0.65 μm, and the density of beads was also reduced. The membranes were rather amorphous, as revealed by X-ray scattering, presumably due to the quenching process associated with the electrospinning process. Water contact angle measurements showed that silver nanoparticles induced significant hidrophobicity in the membranes as neat PLA membrane had a contact angle of 54° and PLA/Ag membrane exhibited an angle of 115°.

Surface-modified halloysite nanotubes as fillers applied in reinforcing the performance of polytetrafluoroethylene

Clay Minerals ◽  
2018 ◽  
Vol 53 (4) ◽  
pp. 643-656 ◽  
Author(s):  
Zhi-Lin Cheng ◽  
Xing-Yu Chang ◽  
Zan Liu ◽  
Dun-Zhong Qin
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Sodium Dodecyl ◽  
Halloysite Nanotubes ◽  
Angle Measurements ◽  
Transmission Electron ◽  
Contact Angle Measurements ◽  
Ftir Spectrometry ◽  
Surface Modified ◽  
Scanning Electron

ABSTRACTIn order to improve the dispersibility of halloysite nanotubes (HNTs) in polytetrafluoroethylene (PTFE), the modification of HNT surfaces was studied with three types of modifiers (polymethyl methacrylate [PMMA], sodium dodecyl sulfate [SDS] and carboxylic acid). The modified HNTs were characterized by Fourier-transform infrared (FTIR) spectrometry, transmission electron microscopy (TEM), scanning electron microscopy (SEM) and contact angle measurements. The HNTs were used to reinforce the mechanical properties of PTFE. The mechanical results indicated that the tensile strength of the modified HNT-filled PTFE nanocomposites (F-HNT/PTFE) improved to an acceptable degree and Young's modulus increased significantly. The tribological results showed that the wear rate of F-HNT/PTFE decreased by 21–82 and 9–40 times compared to pure PTFE and the pristine F-HNT/PTFE, respectively.

scholarly journals Protection of LiFePO4 against Moisture

Materials ◽  
2020 ◽  
Vol 13 (4) ◽  
pp. 942 ◽  
Author(s):  
Nicolas Delaporte ◽  
Michel L. Trudeau ◽  
Daniel Bélanger ◽  
Karim Zaghib
Keyword(s):  
Photoelectron Spectroscopy ◽  
Inductively Coupled Plasma ◽  
Atomic Emission ◽  
Carbon Surface ◽  
Water Contact ◽  
Inductively Coupled ◽  
Spontaneous Reduction ◽  
Angle Measurements ◽  
Contact Angle Measurements ◽  
Carbon Coated

In this study, a carbon-coated LiFePO4 (LFP/C) powder was chemically grafted with trifluoromethylphenyl groups in order to increase its hydrophobicity and to protect it from moisture. The modification was carried out by the spontaneous reduction of in situ generated 4-trifluoromethylphenyl ions produced by the diazotization of 4-trifluoromethylaniline. X-ray photoelectron spectroscopy was used to analyze the surface organic species of the modified powder. The hydrophobic properties of the modified powder were investigated by carrying out its water contact angle measurements. The presence of the trifluoromethylphenyl groups on the carbon-coated LiFePO4 powder increased its stability in deionized water and reduced its iron dissolution in the electrolyte used for assembling the battery. The thermogravimetric and inductively coupled plasma atomic emission spectroscopy analyses revealed that 0.2–0.3 wt.% Li was deinserted during grafting and that the loading of the grafted molecules varied from 0.5 to 0.8 wt.% depending on the reaction conditions. Interestingly, the electrochemical performance of the modified LFP/C was not adversely affected by the presence of the trifluoromethylphenyl groups on the carbon surface. The chemical relithiation of the grafted samples was carried out using LiI as the reducing agent and the lithium source in order to obtain fully lithiated grafted powders.

Sign in / Sign up

Export Citation Format

Share Document