scholarly journals TiO2/Halloysite Composites Codoped with Carbon and Nitrogen from Melamine and Their Enhanced Solar-Light-Driven Photocatalytic Performance

2015 ◽  
Vol 2015 ◽  
pp. 1-8 ◽  
Author(s):  
Pengcheng Yao ◽  
Shuhui Zhong ◽  
Zhurui Shen
Keyword(s):  
Photoelectron Spectroscopy ◽  
Photocatalytic Performance ◽  
Weight Ratio ◽  
Halloysite Nanotubes ◽  
Degradation Efficiency ◽  
Solar Light ◽  
Potential Candidate ◽  
X Ray ◽  
Ft Ir ◽  
C And N

Carbon (C) and nitrogen (N) codoped anatase TiO2/amorphous halloysite nanotubes (C+N-TiO2/HNTs) were fabricated using melamine as C and N source. The samples prepared by different weight ratios of melamine and TiO2were investigated by X-ray diffraction (XRD) and UV-vis diffuse reflectance spectrometer. It is shown that the doping amounts of C and N could influence the photocatalytic performance of as-prepared composites. When the weight ratio of melamine/TiO2is 4.5, the C+N-TiO2/HNTs exhibited the best photocatalytic degradation efficiency of methyl blue (MB) under solar light irradiation. The obtained C+N-TiO2/HNTs were characterized by transmission electron microscopy (TEM), N2adsorption-desorption isotherm (BET), X-ray photoelectron spectroscopy (XPS), and Fourier transform infrared spectrum (FT-IR). The results showed that the aggregation was effectively reduced, and TiO2nanoparticles could be uniformly deposited on the surface of HNTs. This leads to an increase of their specific surface area. XPS and FT-IR analyses indicated TiO2particles were doped successfully with C and N via the linkage of the Ti–O–N, O–Ti–N, and Ti–O–C. Photocatalytic experiments showed that C+N-TiO2/HNTs had higher degradation efficiency of MB than TiO2/HNTs. This makes the composite a potential candidate for the photocatalytic wastewater treatment.

Preparation and Characterization of TiO2 Nanoparticle with SiO2 Shell

2011 ◽  
Vol 233-235 ◽  
pp. 1188-1191
Author(s):  
Hong Cai ◽  
Yan Chen ◽  
Yun Ying Wu
Keyword(s):  
Photoelectron Spectroscopy ◽  
Photocatalytic Performance ◽  
Sol Gel ◽  
Chemical Components ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ft Ir ◽  
Bonding Phase ◽  
Hydrolysis Of

Nano-TiO2 particles were prepared by sol-gel method, of which the surfaces were coated by SiO2. The coating was achieved by the hydrolysis of sodium silicate (Na2SiO3) in ammonium chloride (NH4Cl). The surface bonding, phase constitution and chemical components of the samples were characterized by Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction(XRD) and X-ray photoelectron spectroscopy (XPS). The mechanism of the SiO2 coating process onto TiO2 surface was analyzed. Results show that SiO2 particles were immobilized on the TiO2 surface via Ti—O—Si bondings, which formed at the interface. The SiO2 layer on TiO2 surface was amorphous, the photocatalytic performance was decreased of the TiO2 while its stability was enhanced after surface modification.

scholarly journals Manipulating the Structure and Characterization of Sr1−xLaxTiO3 Nanocubes toward the Photodegradation of 2-Naphthol under Artificial Solar Light

Catalysts ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 564
Author(s):  
Minh-Vien Le ◽  
Ngoc-Quoc-Duy Vo ◽  
Quoc-Cuong Le ◽  
Vy Anh Tran ◽  
T. Que-Phuong Phan ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Organic Contaminants ◽  
Parent Compound ◽  
Degradation Efficiency ◽  
Solar Light ◽  
Sem Images ◽  
Absorption Region ◽  
X Ray ◽  
Degradation Rate Constant ◽  
La Doped

Effective La-doped SrTiO3 (Sr1−xLaxTiO3, x = 0–0.1 mol.% La-doped) nanocubes were successfully synthesized by a hydrothermal method. The influence of different La dopant concentrations on the physicochemical properties of the host structure of SrTiO3 was fully characterized. X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) revealed that the Sr2+ in the crystal lattice of SrTiO3 was substituted by La3+. As a result, the absorption region of the Sr1−xLaxTiO3 could be extended to visible light. Scanning electron microscopy (SEM) images confirmed that their morphologies are associated with an increased surface area and an increased La-doping concentration. The decrease in the photoluminescence (PL) intensity of the dopant samples showed more defect levels created by the dopant La+3 cations in the SrTiO3 structure. The photocatalytic activities of Sr1−xLaxTiO3 were evaluated with regard to the degradation of 2-naphthol at typical conditions under artificial solar light. Among the candidates, Sr0.95La0.05TiO3 exhibited the highest photocatalytic performance for the degradation of 2-naphthol, which reached 92% degradation efficiency, corresponding to a 0.0196 min−1 degradation rate constant, within 180 minutes of irradiation. Manipulating the structure of Sr1−xLaxTiO3 nanocubes could produce a more effective and stable degradation efficiency than their parent compound, SrTiO3. The parameters remarkably influence the Sr1−xLaxTiO3 nanocubes’ structure, and their degradation efficiencies were also studied. Undoubtedly, substantial breakthroughs of Sr1−xLaxTiO3 nanocube photocatalysts toward the treatment of organic contaminants from industrial wastewater are expected shortly.

scholarly journals Characterization of Tio2 And An As-Prepared Tio2/Sio2 Composite And Their Photocatalytic Performance For The Reduction Of Low-Concentration N-NO3- In Water

2021 ◽  
Author(s):  
Wanzhen Zhong ◽  
Weizhang Fu ◽  
Shujuan Sun ◽  
Lingsheng Wang ◽  
Huaihao Liu ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Photocatalytic Performance ◽  
Uv Light ◽  
Removal Rate ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
X Ray ◽  
Load Rate ◽  
Hole Scavenger ◽  
Ft Ir

Abstract Excessive N-NO3- water pollution has become a widespread and serious problem that threatens human and ecosystem health. Here, a TiO2/SiO2 composite photocatalyst was prepared via the sol-gel/hydrothermal method. TiO2 and TiO2/SiO2 were characterized by X-ray diffraction (XRD), UV-Vis differential reflectance spectroscopy (DRS), Fourier infrared (FT-IR) spectroscopy, X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDS). Afterward, the photocatalytic performance of TiO2 and TiO2/SiO2 to reduce low nitrate concentrations (30 mgN·L-1) under UV light were evaluated and the effects of different factors on this process were investigated, after which the reaction conditions were optimized. Removal rates of up to 99.93% were achieved at a hole scavenger (formic acid) concentration of 0.6 mL·L-1, a CO2 flow rate of 0.1 m3·h-1, and a TiO2 concentration of 0.9 g·L-1. In contrast, TiO2/SiO2 at a 1.4 g·L-1 concentration and a TiO2 load rate of 40% achieved a removal rate of 83.48%,But with more than 98% of nitrogen generation rate.NO2- and NH4+ were the minor products, whereas N2 was the main product.

scholarly journals Synthesis of Magnetic Ferrocene-Containing Polymer with Photothermal Effects for Rapid Degradation of Methylene Blue

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 558
Author(s):  
Wenhui Zhu ◽  
Caiyun Zhang ◽  
Yali Chen ◽  
Qiliang Deng
Keyword(s):  
Methylene Blue ◽  
Photoelectron Spectroscopy ◽  
Room Temperature ◽  
Degradation Rate ◽  
Model Compound ◽  
Vibrating Sample Magnetometer ◽  
Simulated Sunlight ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ft Ir

Photothermal materials are attracting more and more attention. In this research, we synthesized a ferrocene-containing polymer with magnetism and photothermal properties. The resulting polymer was characterized by Fourier-transform infrared (FT-IR), vibrating sample magnetometer (VSM), scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and thermogravimetric analysis (TGA). Its photo-thermocatalytic activity was investigated by choosing methylene blue (MB) as a model compound. The degradation percent of MB under an irradiated 808 nm laser reaches 99.5% within 15 min, and the degradation rate is 0.5517 min−1, which is 145 times more than that of room temperature degradation. Under irradiation with simulated sunlight, the degradation rate is 0.0092 min−1, which is approximately 2.5 times more than that of room temperature degradation. The present study may open up a feasible route to degrade organic pollutants.

Chemical Structures of Native Oxides Formed During Wet Chemical Treatments on NH4F Treated Si(111) Surfaces

1992 ◽  
Vol 259 ◽  
Author(s):  
Takeo Hattori ◽  
Hiroki Ogawa
Keyword(s):  
Photoelectron Spectroscopy ◽  
Attenuated Total Reflection ◽  
Native Oxide ◽  
X Ray ◽  
Chemical Treatments ◽  
Chemical Structures ◽  
Native Oxides ◽  
Ft Ir ◽  
Wet Chemical ◽  
Silicon Interface

ABSTRACTChemical structures of native oxides formed during wet chemical treatments on NH4F treated Si(111) surfaces were investigated using X-ray Photoelectron Spectroscopy (XPS) and Fourier Transformed Infrared Attenuated Total Reflection(FT-IR-ATR). It was found that the amounts of Si-H bonds in native oxides and those at native oxide/silicon interface are negligibly small in the case of native oxides formed in H2SO4-H2O2-H2O solution. Based on this discovery, it was confirmed that native oxides can be characterized by the amount of Si-H bonds in native oxides. Furthermore, it was found that the combination of various wet chemical treatments with the treatment in NH4OH-H2O2-H2O solution results in the drastic decrease in the amount of Si-H bonds in native oxides.

scholarly journals Dual Light- and pH-Responsive Composite of Polyazo-Derivative Grafted Cellulose Nanocrystals

Materials ◽  
2018 ◽  
Vol 11 (9) ◽  
pp. 1725 ◽  
Author(s):  
Xiaohong Liu ◽  
Ming Li ◽  
Xuemei Zheng ◽  
Elias Retulainen ◽  
Shiyu Fu
Keyword(s):  
Cellulose Nanocrystals ◽  
Photoelectron Spectroscopy ◽  
Surface Composition ◽  
X Ray Diffraction ◽  
Responsive Materials ◽  
X Ray ◽  
Ph Response ◽  
Transmission Electron ◽  
Ft Ir ◽  
Hexyl Methacrylate

As a type of functional group, azo-derivatives are commonly used to synthesize responsive materials. Cellulose nanocrystals (CNCs), prepared by acid hydrolysis of cotton, were dewatered and reacted with 2-bromoisobuturyl bromide to form a macro-initiator, which grafted 6-[4-(4-methoxyphenyl-azo) phenoxy] hexyl methacrylate (MMAZO) via atom transfer radical polymerization. The successful grafting was supported by Fourier transform infrared spectroscopy (FT-IR) and Solid magnetic resonance carbon spectrum (MAS 13C-NMR). The morphology and surface composition of the poly{6-[4-(4-methoxyphenylazo) phenoxy] hexyl methacrylate} (PMMAZO)-grafted CNCs were confirmed with Transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). The grafting rate on the macro-initiator of CNCs was over 870%, and the polydispersities of branched polymers were narrow. The crystal structure of CNCs did not change after grafting, as determined by X-ray diffraction (XRD). The polymer PMMAZO improved the thermal stability of cellulose nanocrystals, as shown by thermogravimetry analysis (TGA). Then the PMMAZO-grafted CNCs were mixed with polyurethane and casted to form a composite film. The film showed a significant light and pH response, which may be suitable for visual acid-alkali measurement and reversible optical storage.

Preparation and Characterization of Ni2+-Montmorillonite/Polyvinyl Alcohol Water-Soluble Nanocomposite Film

2005 ◽  
Vol 13 (8) ◽  
pp. 839-846 ◽  
Author(s):  
Li-Ping Wang ◽  
Yun-Pu Wang ◽  
Fa-Ai Zhang
Keyword(s):  
Polyvinyl Alcohol ◽  
Photoelectron Spectroscopy ◽  
Thermal Characteristics ◽  
Water Soluble ◽  
Scanning Calorimetry ◽  
Xps Spectra ◽  
X Ray ◽  
Alcohol Water ◽  
Ft Ir ◽  
Silicate Layers

A new type of nano-composite film was prepared from polyvinyl alcohol, Ni2+-montmorillonite (Ni2+-MMT), defoamer, a levelling agent and a plasticizer. Its thermal characteristics were studied by Differential Scanning Calorimetry (DSC). The intermolecular interactions were measured by Fourier transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS), and the tensile strength (TS) and elongation at break (%E) were measured. The microstructures were studied by X-ray diffraction (XRD) and atomic force microscopy (AFM). FT-IR and XPS spectra indicated that cross-linking has taken place between PVA and Ni2+-MMT. XRD and AFM indicate that the PVA molecules had inserted themselves into the silicate layers of MMT, exfoliating them and dispersing them randomly into the PVA matrix. Compared to pure PVA film, the TS of the films was increased and %E decreased when the Ni2+-Montmorillonite was added and the dissolution temperature of the film was also reduced.

scholarly journals Photocatalytic activity of Cu2O/ZnO nanocomposite for the decomposition of methyl orange under visible light irradiation

2019 ◽  
Vol 26 (1) ◽  
pp. 104-113 ◽  
Author(s):  
Xian-sheng Wang ◽  
Yu-duo Zhang ◽  
Qiao-chu Wang ◽  
Bo Dong ◽  
Yan-jia Wang ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Methyl Orange ◽  
Photoelectron Spectroscopy ◽  
Visible Region ◽  
Methyl Orange Solution ◽  
Degradation Efficiency ◽  
X Ray ◽  
Transmission Electron ◽  
Consistent Performance ◽  
Two Phases

AbstractZnO is modified by Cu2O by the process of precipitation and calcination. X-ray diffraction has shown that Cu2O/ZnO catalysts are made of highly purified cubic Cu2O and hexagonal ZnO. Scanning electron microscopy and transmission electron microscopy have shown that ZnO adhered to the surface of Cu2O. Due to the doping of Cu2O, the absorption range of the Cu2O/ZnO catalyst is shifted from the ultraviolet to the visible region due to diffuse reflection. X-ray photoelectron spectroscopy and photoluminescence spectra have confirmed that there is a substantial interaction between the two phases of the resultant catalyst. The degradation efficiency of Cu2O/ZnO on methyl orange solution is obviously enhanced compared to Cu2O and ZnO. The maximum degradation efficiency is 98%. The degradation efficiency is affected by the pH of the solution and initial concentration. After three rounds of recycling, the degradation rate is almost same. This shows a consistent performance of Cu2O/ZnO. The increase in catalytic ability is related to the lattice interaction caused by the doping of Cu2O.

scholarly journals Preparation and characterization of self-cleaning cotton fabric loaded with self-dispersive and reactive biphasic TiO2

2021 ◽  
Author(s):  
Kuang Wang ◽  
Jiayi Chen ◽  
Jialong Tian ◽  
Dawei Gao ◽  
Xiaolei Song ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Cotton Fabrics ◽  
Ammonia Solution ◽  
X Ray ◽  
Washing Fastness ◽  
Fastness Property ◽  
Structure Dispersion ◽  
Ft Ir ◽  
Self Cleaning

Abstract In this article, amino functionalized TiO2 (TiO2/KH550) was obtained in a mild reaction between 3-aminopropyltriethoxysilane and TiO2 with the aid of concentrated ammonia solution. 4-(4,6-dichloro-1,3,5-triazine-2-yl) amino) sodium benzenesulfonate (SAT) was synthesized and characterized by 1H NMR and fourier transform infrared spectroscopy (FT-IR). Self-dispersive and reactive TiO2 (TiO2/KH550/SAT) was prepared by nucleophile substitution reaction between TiO2/KH550 and SAT. Finally, cotton fabrics loaded with different amounts of TiO2/KH550/SAT were achieved by pad-dry-cure method. The chemical structure, dispersion and thermal performance of TiO2, TiO2/KH550 and TiO2/KH550/SAT were investigated by FT-IR, zeta potential and thermogravimetric analysis (TG). The crystalline phase, morphology, chemical composition and optical absorption property of cotton fabrics were studied by X-ray diffraction (XRD), scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS) and ultraviolet-visible diffuse reflectance spectroscopy (UV-Vis DRS). Moreover, the anti-ultraviolet, self-cleaning and washing fastness properties of cotton fabrics were investigated. It has been found that TiO2/KH550/SAT demonstrated excellent dispersion stability in aqueous even after standing for a month. Cotton fabrics loaded with TiO2/KH550/SAT possessed adorable anti-ultraviolet performance, highly efficient and durable self-cleaning activity as well as appreciable washing fastness property. The mechanism and possible reactions for the preparation of self-cleaning cotton fabrics loaded with TiO2/KH550/SAT were proposed.

Preparation and Photocatalytic Properties of Rod-Shaped TiO2 Based on Salix Fiber

2014 ◽  
Vol 609-610 ◽  
pp. 250-254
Author(s):  
Ya Bin Li ◽  
Jin Tian Huang ◽  
Yan Fei Pan
Keyword(s):  
Photocatalytic Performance ◽  
Sol Gel ◽  
Average Diameter ◽  
X Ray Diffraction ◽  
Nanocomposite Structure ◽  
X Ray ◽  
Infrared Spectrometer ◽  
Ft Ir ◽  
Degradation Of Methyl Orange ◽  
Scanning Electron

In the paper, the TiO2nanomaterials adopted the microcrystalline cellulose as the template by the template method and sol-gel method was prepared. Through the infrared spectrometer (FT-IR), scanning electron microscope (SEM), X-ray diffraction (XRD), the surface morphology, composition and the type of the samples were characterized respectively. The influence of the macro morphology of TiO2photocatalytic performance to use the reaction of decolorization and degradation of methyl orange as model was analyzed. The results showed that TiO2which was produced by the template of sallix fiber was Rod-shaped and the average diameter size of nanocomposite structure was 20.592 nm, which can provide a new method of producing other morphology of TiO2.

Sign in / Sign up

Export Citation Format

Share Document