scholarly journals Image Analysis Determination of the Influence of Surface Structure of Silicone Rubbers on Biofouling

2015 ◽  
Vol 2015 ◽  
pp. 1-8 ◽  
Author(s):  
Sevil Atarijabarzadeh ◽  
Fritjof Nilsson ◽  
Henrik Hillborg ◽  
Sigbritt Karlsson ◽  
Emma Strömberg
Keyword(s):  
Image Analysis ◽  
Silicone Rubber ◽  
Microbial Growth ◽  
Plane Surface ◽  
Contact Angle Hysteresis ◽  
Contact Angles ◽  
Homogeneous Distribution ◽  
Textured Surface ◽  
Textured Surfaces ◽  
Band Formation

This study focuses on how the texture of the silicone rubber material affects the distribution of microbial growth on the surface of materials used for high voltage insulation. The analysis of surface wetting properties showed that the textured surfaces provide higher receding contact angles and therefore lower contact angle hysteresis. The textured surfaces decrease the risk for dry band formation and thus preserve the electrical properties of the material due to a more homogeneous distribution of water on the surface, which, however, promotes the formation of more extensive biofilms. The samples were inoculated with fungal suspension and incubated in a microenvironment chamber simulating authentic conditions in the field. The extent and distribution of microbial growth on the textured and plane surface samples representing the different parts of the insulator housing that is shank and shed were determined by visual inspection and image analysis methods. The results showed that the microbial growth was evenly distributed on the surface of the textured samples but restricted to limited areas on the plane samples. More intensive microbial growth was determined on the textured samples representing sheds. It would therefore be preferable to use the textured surface silicone rubber for the shank of the insulator.

scholarly journals Biomimetic Approach for the Elaboration of Highly Hydrophobic Surfaces: Study of the Links between Morphology and Wettability

Biomimetics ◽  
2021 ◽  
Vol 6 (2) ◽  
pp. 38
Author(s):  
Quentin Legrand ◽  
Stephane Benayoun ◽  
Stephane Valette
Keyword(s):  
Contact Angle ◽  
Ginkgo Biloba ◽  
Contact Angle Hysteresis ◽  
Contact Angles ◽  
Textured Surfaces ◽  
Replication Process ◽  
Wetting Behavior ◽  
Static Contact ◽  
Biomimetic Approach ◽  
Highly Hydrophobic

This investigation of morphology-wetting links was performed using a biomimetic approach. Three natural leaves’ surfaces were studied: two bamboo varieties and Ginkgo Biloba. Multiscale surface topographies were analyzed by SEM observations, FFT, and Gaussian filtering. A PDMS replicating protocol of natural surfaces was proposed in order to study the purely morphological contribution to wetting. High static contact angles, close to 135∘, were measured on PDMS replicated surfaces. Compared to flat PDMS, the increase in static contact angle due to purely morphological contribution was around 20∘. Such an increase in contact angle was obtained despite loss of the nanometric scale during the replication process. Moreover, a significant decrease of the hysteresis contact angle was measured on PDMS replicas. The value of the contact angle hysteresis moved from 40∘ for flat PDMS to less than 10∘ for textured replicated surfaces. The wetting behavior of multiscale textured surfaces was then studied in the frame of the Wenzel and Cassie–Baxter models. Whereas the classical laws made it possible to describe the wetting behavior of the ginkgo biloba replications, a hierarchical model was developed to depict the wetting behavior of both bamboo species.

Dropwise Condensation Underneath Chemically Textured Surfaces: Simulation and Experiments

2010 ◽  
Vol 133 (2) ◽  
Author(s):  
Basant Singh Sikarwar ◽  
Nirmal Kumar Battoo ◽  
Sameer Khandekar ◽  
K. Muralidhar
Keyword(s):  
Contact Angle ◽  
Model Simulation ◽  
Contact Angle Hysteresis ◽  
Saturation Temperature ◽  
Static Contact Angle ◽  
Order Effects ◽  
Textured Surface ◽  
Dropwise Condensation ◽  
Textured Surfaces ◽  
Static Contact

Experimental observations of dropwise condensation of water vapor on a chemically textured surface of glass and its detailed computer simulation are presented. Experiments are focused on the pendant mode of dropwise condensation on the underside of horizontal and inclined glass substrates. Chemical texturing of glass is achieved by silanation using octyl-decyl-tri-chloro-silane (C18H37C13Si) in a chemical vapor deposition process. The mathematical model is built in such a way that it captures all the major physical processes taking place during condensation. These include growth due to direct condensation, droplet coalescence, sliding, fall-off, and renucleation of droplets. The effects arising from lyophobicity, namely, the contact angle variation and its hysteresis, inclination of the substrate, and saturation temperature at which the condensation is carried out, have been incorporated. The importance of higher order effects neglected in the simulation is discussed. The results of model simulation are compared with the experimental data. After validation, a parametric study is carried out for cases not covered by the experimental regime, i.e., various fluids, substrate inclination angle, saturation temperature, and contact angle hysteresis. Major conclusions arrived at in the study are the following: The area of droplet coverage decreases with an increase in both static contact angle of the droplet and substrate inclination. As the substrate inclination increases, the time instant of commencement of sliding of the droplet is advanced. The critical angle of inclination required for the inception of droplet sliding varies inversely with the droplet volume. For a given static contact angle, the fall-off time of the droplet from the substrate is a linear function of the saturation temperature. For a given fluid, the drop size distribution is well represented by a power law. Average heat transfer coefficient is satisfactorily predicted by the developed model.

scholarly journals Blood Platelet’s Behavior on Nanostructured Superhydrophobic Surface

2008 ◽  
Vol 2 ◽  
pp. 129-136 ◽  
Author(s):  
Ming Zhou ◽  
Jia Hong Yang ◽  
Xia Ye ◽  
Ao Ran Zheng ◽  
Gang Li ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Superhydrophobic Surface ◽  
Platelet Adhesion ◽  
Blood Compatibility ◽  
Blood Platelet ◽  
Contact Angles ◽  
Textured Surface ◽  
Textured Surfaces ◽  
Scanning Electron

Regular arrays of micro-pillars and nano-grooves structures on the silicon wafer are fabricated by using soft lithography, and the three dimension morphology of textured surface is observed by using scanning electron microscopy (SEM) and atomic force microscope (AFM). The static water contact angles are measured by using contact angle meter to characterize the wettabilities of these surfaces. To investigate how the presence of topography and the variations of wettability affect the haemocompatibility of textured surface contacted with blood, different patterned surfaces are designed and fabricated, and blood platelet adhesion test is carried out on these surfaces. The adhesion and coagulation of platelets are inspected by scanning electron microscopy (SEM). Experimental data presented in this paper indicate that different surface roughness and wettability are the important factors for blood platelet adhesion. The amount of adsorbed blood platelet is low on textured surfaces, compared with that on the flat surface. Especially, there is no coagulation and activation on the surface with nanometer grooves. That is to say, the superhydrophobic surface is apt to decrease blood platelet adhesion. The study suggests that surface with suitable wettabililty and textured structures exhibits superior blood compatibility.

scholarly journals Superhydrophobic Surface Preparation and Wettability Transition of Titanium Alloy with Micro/Nano Hierarchical Texture

Materials ◽  
2018 ◽  
Vol 11 (11) ◽  
pp. 2210 ◽  
Author(s):  
Zhiru Yang ◽  
Chongchong Zhu ◽  
Nan Zheng ◽  
Dezheng Le ◽  
Jianzhong Zhou
Keyword(s):  
Contact Angle ◽  
Titanium Alloy ◽  
Low Temperature ◽  
Superhydrophobic Surface ◽  
Contact Angles ◽  
Surface Wettability ◽  
Hydroxyl Groups ◽  
Textured Surface ◽  
Textured Surfaces ◽  
Low Temperature Annealing

Microstructures are applied to various hydrophobic/hydrophilic surfaces due to the role of adjusting the surface wettability. In this paper, a 1064 nm pulsed picosecond laser was applied to prepare a micro/nano hierarchical structure on the surface of the titanium alloy (Ti-6Al-4V). The microstructures consist of dimple arrays with various diameters, depths, and areal densities. They are obtained by controlling the pulse energy and the number of pulses. The nanostructures are periodic ripples, which are defined as laser-induced periodic surface structure (LIPSS), and the dimensional parameter of LIPSS can be adjusted by changing the laser energy density and scanning speed. The contact angles of various laser textured surfaces were measured. It is found that the contact angle increases with the density of micro-textured surface increases, and the wetting state of textured surfaces conforms to the Cassie model. Some laser processed samples were subjected to low-temperature annealing treatment. It is observed that the low-temperature annealing process can accelerate the surface wettability transition significantly, which is attributed to the change of the hydroxyl groups on the surface. Finally, a superhydrophobic surface with the maximum contact angle of 144.58° is obtained.

scholarly journals Wettability control of polymeric microstructures replicated from laser-patterned stamps

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Yangxi Fu ◽  
Marcos Soldera ◽  
Wei Wang ◽  
Stephan Milles ◽  
Kangfa Deng ◽  
...  
Keyword(s):  
Contact Angle Hysteresis ◽  
Contact Angles ◽  
Spatial Period ◽  
Structured Surfaces ◽  
High Adhesion ◽  
Direct Laser ◽  
Periodic Microstructures ◽  
Structure Height ◽  
Direct Laser Interference Patterning ◽  
Micropillar Arrays

AbstractIn this study, two-step approaches to fabricate periodic microstructures on polyethylene terephthalate (PET) and poly(methyl methacrylate) (PMMA) substrates are presented to control the wettability of polymeric surfaces. Micropillar arrays with periods between 1.6 and 4.6 µm are patterned by plate-to-plate hot embossing using chromium stamps structured by four-beam Direct Laser Interference Patterning (DLIP). By varying the laser parameters, the shape, spatial period, and structure height of the laser-induced topography on Cr stamps are controlled. After that, the wettability properties, namely the static, advancing/receding contact angles (CAs), and contact angle hysteresis were characterized on the patterned PET and PMMA surfaces. The results indicate that the micropillar arrays induced a hydrophobic state in both polymers with CAs up to 140° in the case of PET, without modifying the surface chemistry. However, the structured surfaces show high adhesion to water, as the droplets stick to the surfaces and do not roll down even upon turning the substrates upside down. To investigate the wetting state on the structured polymers, theoretical CAs predicted by Wenzel and Cassie-Baxter models for selected structured samples with different topographical characteristics are also calculated and compared with the experimental data.

Multiscale Analysis on Friction-Reducing Characteristics of Textured Surface in Nanoscale Sliding Contacts

2011 ◽  
Vol 86 ◽  
pp. 649-652
Author(s):  
Rui Ting Tong ◽  
Geng Liu ◽  
Lan Liu ◽  
Shang Jun Ma
Keyword(s):  
Copper Substrate ◽  
Dynamics Simulation ◽  
Textured Surface ◽  
Face Centered Cubic ◽  
Textured Surfaces ◽  
Sliding Contacts ◽  
Friction Forces ◽  
Surface Textures ◽  
Force Reduction ◽  
Face Centered

A multiscale method coupled molecular dynamics simulation and finite element method is used to investigate two dimensional nanoscale sliding contacts between a rigid cylindrical tip and an elastic face centered cubic copper substrate with textured surface, in which adhesive effects are considered. Two series of nanoscale surface textures with different asperity shape, different asperity heights and different spacing between asperities are designed. Through the friction forces comparisons between smooth surface and textured surfaces, a better shape is advised to indicate that asperity shape plays an important role in friction force reduction. With proper asperity height and proper spacing between asperities, surface textures can reduce friction forces effectively.

Relief reconstruction of rough-textured surface through image analysis

2003 ◽  
Author(s):  
Anis Benslimane ◽  
Majdi Khoudeir ◽  
Jacques Brochard ◽  
Vincent Legeay ◽  
Min-Tan Do
Keyword(s):  
Image Analysis ◽  
Textured Surface

The Surface Modification with Fluorocarbon Thin Films for the Prevention of Stiction in Mems

1998 ◽  
Vol 518 ◽  
Author(s):  
Sang-Ho Lee ◽  
Myong-Jong Kwon ◽  
Jin-Goo Park ◽  
Yong-Kweon Kim ◽  
Hyung-Jae Shin
Keyword(s):  
Contact Angle ◽  
Contact Angle Hysteresis ◽  
Contact Angles ◽  
Fluorocarbon Films ◽  
Perfluorodecanoic Acid ◽  
Large Hysteresis ◽  
Static Contact ◽  
Receding Contact ◽  
Highly Hydrophobic ◽  
Receding Contact Angle

AbstractHighly hydrophobic fluorocarbon films were prepared by the vapor phase (VP) deposition method in a vacuum chamber using both liquid (3M's FC40, FC722) and solid sources (perfluorodecanoic acid (CF3(CF2)8COOH), perfluorododecane (C12F26)) on Al, Si and oxide coated wafers. The highest static contact angles of water were measured on films deposited on aluminum substrate. But relatively lower contact angles were obtained on the films on Si and oxide wafers. The advancing and receding contact angle analysis using a captive drop method showed a large contact angle hysteresis (ΔH) on the VP deposited fluorocarbon films. AFM study showed poor film coverage on the surface with large hysteresis. FTIR-ATR analysis positively revealed the stretching band of CF2 groups on the VP deposited substrates. The thermal stability of films was measured at 150°C in air and nitrogen atmospheres as a function of time. The rapid decrease of contact angles was observed on VP deposited FC and PFDA films in air. However, no decrease of contact angle on them was observed in N2.

scholarly journals Which Is the Motion State of a Droplet on an Inclined Hydrophilic Rough Surface in Gravity: Pinned or Sliding?

2021 ◽  
Vol 11 (9) ◽  
pp. 3734
Author(s):  
Jian Dong ◽  
Youhai Guo ◽  
Long Jiao ◽  
Chao Si ◽  
Yinbo Bian ◽  
...  
Keyword(s):  
Rough Surface ◽  
Contact Angle Hysteresis ◽  
Minimum Energy ◽  
Contact Angles ◽  
Microfluidic Chips ◽  
Motion State ◽  
Receding Contact ◽  
Novel Design ◽  
Minimum Energy Dissipation ◽  
Good Agreement

The motion state of a droplet on an inclined, hydrophilic rough surface in gravity, pinned or sliding, is governed by the balance between the driving and the pinned forces. It can be judged by the droplet’s shape on the inclined hydrophilic rough surface and the droplet’s contact angle hysteresis. In this paper, we used the minimum energy theory, the minimum energy dissipation theory, and the nonlinear numerical optimization algorithm to establish Models 1–3 to calculate out the advancing/receding contact angles (θa/θr), the initial front/rear contact angles (θ1−0/θ2−0) and the dynamic front/rear contact angles (θ1−*/θ2−*) for a droplet on a rough surface. Also, we predicted the motion state of the droplet on an inclined hydrophilic rough surface in gravity by comparing θ1−0(θ2−0) and θ1−*(θ2−*) with θa(θr). Experiments were done to verify the predictions. They showed that the predictions were in good agreement with the experimental results. These models are promising as novel design approaches of hydrophilic functional rough surfaces, which are frequently applied to manipulate droplets in microfluidic chips.

Sign in / Sign up

Export Citation Format

Share Document