scholarly journals Integrated Analysis of Permeability Reduction Caused by Polymer Retention for Better Understanding Polymer Transport

2015 ◽  
Vol 2015 ◽  
pp. 1-10
Author(s):  
ByungIn Choi ◽  
Jinsuk Choi ◽  
Kun Sang Lee
Keyword(s):  
Flow Behavior ◽  
Polymer Concentration ◽  
Integrated Analysis ◽  
Permeability Reduction ◽  
Reservoir Permeability ◽  
Polymer Transport ◽  
Concentration Loss ◽  
Polymer Retention ◽  
Interpretation Method ◽  
Reduction Factors

Polymer retention is one of the most important factors to govern polymer propagation through porous media, determining whether successful or not. The focus of previous studies has been limited to polymer concentration loss caused by the retention; not only change in polymer concentration, but also reduction in reservoir permeability is the main issue for theoretical transport study. Due to the lack of accuracy of Langmuir isotherm describing the polymer retention mechanisms, this study proposes a new type of matching interpretation method to correlate the permeability reduction factors from experiments to permeability. In order to solve the problem of poorly matching results between estimation and observation, use of nonadsorptive constant conditionally selected in matching process was made. Based on the threshold permeability reduction factors, approximate critical permeability can be calculated to which nonadsorptive constant would be applied. Results showed significant improvements in the estimation of permeability reduction for both low and high permeability cores. In addition, effects of permeability reduction on polymer transport in field scale were analyzed using the proposed matching model. Thus, not only does this interpretation method help to evaluate prediction for accurate flow behavior, but also unwanted risk can be evaluated.

Drag Reducing Polymer in Helicoidal Flow

1981 ◽  
Vol 103 (4) ◽  
pp. 491-496 ◽  
Author(s):  
J. T. Kuo ◽  
L. S. G. Kovasznay
Keyword(s):  
Drag Reduction ◽  
Polymer Solution ◽  
Ph Value ◽  
Flow Behavior ◽  
Superposition Principle ◽  
Polymer Concentration ◽  
Second Phase ◽  
Additional Parameter ◽  
Solution Flow ◽  
Screw Pump

A novel flow configuration was explored for the study of the behavior of drag reducing polymers. A screw pump consisting of a smooth cylinder and a concentrically placed screw was used to create a strongly three-dimensional but essentially laminar flow. In the first phase of the study, the static pressure head developed by the screw pump was measured as a function of polymer concentration (polyox 10 to 100 ppm in water). A large increase of the developed head was observed that behaved in an analogous manner to drag reduction as far as concentration and straining of the polymer solution was concerned. In the second phase of the study, a new apparatus was constructed and the additional parameter of a superimposed through flow was included and the degree of failure of the superposition principle was established. Sensitivity of the phenomenon to chemicals like HCl, HNO3, and NaOH in the polymer solution was also studied. When the effect of these chemicals on the polymer solution flow behavior was presented in terms of the pH value of the polymer solution, it showed a similar trend to those observed in drag reduction.

Polyacrylamide Adsorption and Readsorption in Sandstone Porous Media

SPE Journal ◽  
2019 ◽  
Vol 25 (01) ◽  
pp. 497-514 ◽  
Author(s):  
Vitor H. S. Ferreira ◽  
Rosangela B. Z. L. Moreno
Keyword(s):  
Oil Recovery ◽  
Polymer Concentration ◽  
Polymer Adsorption ◽  
Mobility Control ◽  
Polymer Molecule ◽  
Type I ◽  
Type Iv ◽  
Polymer Retention ◽  
Successive Injection ◽  
Flowing Solution

Summary The term polymer retention describes all mechanisms that remove the polymer from the flowing solution, with adsorption being its primary cause. This phenomenon can lead to detrimental effects during polymer enhanced oil recovery (EOR). In this paper, we present an investigation of dynamic polymer adsorption in sandstone-outcrop cores using polymer solutions. We study the effects of permeability and polymer concentration on the adsorption under two conditions: on virgin cores (adsorption) and a previously polymer-flooded core (readsorption). According to the results, two concentration plateaus and two regions of concentration-dependent adsorption characterize the polymer adsorption in a virgin porous medium, following a proposed Type IV isotherm. The transition between the first plateau and the second adsorption region occurs near to the overlapping concentration from dilute to semidilute regimes (cp*). Polymer readsorption increases slightly with the successive injection of banks with a higher polymer concentration, following a Type I (Langmuir) isotherm. For that case, we propose a readsorption mechanism on the basis of the desorption of a polymer molecule section and the adsorption of a new free polymer molecule. The adsorption and readsorption isotherms are similar until cp*, while the adsorption is much higher than readsorption for concentrations higher than cp*. Therefore, if the polymer concentration of the mobility control bank is greater than cp*, the total polymer loss during field applications can be reduced by preinjecting a polymer bank of lower concentration.

Scaling Behavior in Electrohydrodynamic Jetting of Polymeric Solutions

2019 ◽  
Author(s):  
Abhishek K. Singh ◽  
Kaushlendra Dubey ◽  
Rajiv K. Srivastava ◽  
Supreet Singh Bahga
Keyword(s):  
Flow Rate ◽  
Flow Behavior ◽  
Polymer Concentration ◽  
Viscoelastic Behavior ◽  
Scaling Behavior ◽  
Jet Stability ◽  
Polymeric Solutions ◽  
Newtonian Liquids ◽  
The Stability ◽  
Viscoelastic Liquids

Abstract An electrohydrodynamic (EHD) jet forms when a leaky-dielectric liquid issuing out of a needle is accelerated and stretched by electrostatic forces. Stability and scaling behavior of the EHD jet of polymeric solutions depend on electrostatics, fluid mechanics and rheology of the liquid. While EHD jetting of Newtonian liquids have been described in the literature, the effect of non-Newtonian rheology on EHD jetting is still not well-understood. Therefore, we present a detailed experimental investigation of the stability and scaling behavior of EHD jets of polymeric solutions that exhibit non-Newtonian flow behavior. The stability of cone-jet was analyzed by varying flow rate, electric field and polymer concentration. Experiments were performed for polymeric solutions of polycaprolactone (PCL) dissolved in acetic acid. Our experiments show that non-Newtonian viscoelastic behavior can significantly alter the stability characteristics of the EHD jet. We have found that increase of elasticity of polymeric solutions results in enhanced jet stability. Finally, we present the dependence of experimentally measured diameter dj of the EHD jet on the flow rate Q. Experimentally measured diameter of the EHD jet scales as dj ∼ Q0.65 for both Newtonian and non-Newtonian viscoelastic liquids, which can be attributed to dominant inertia forces in our experiment.

scholarly journals Investigation of Surfactant-Polymer Interactions Using Rheology and Surface Tension Measurements

Polymers ◽  
2020 ◽  
Vol 12 (10) ◽  
pp. 2302 ◽  
Author(s):  
Jia Yang ◽  
Rajinder Pal
Keyword(s):  
Surface Tension ◽  
Polymer Solutions ◽  
Flow Behavior ◽  
Polymer Concentration ◽  
Critical Aggregation Concentration ◽  
Ionic Surfactant ◽  
Marginal Effect ◽  
Anionic Polymer ◽  
Flow Behavior Index ◽  
Drag Reducing Polymer

The interactions between surfactants and a drag-reducing polymer were investigated at a low polymer concentration of 500 ppm, using measurements of the rheology and surface activity of surfactant-polymer solutions. A well-known drag-reducing polymer (anionic sodium carboxymethyl cellulose) and five different surfactants (two anionic, two non-ionic, and one zwitterionic) were selected for the interaction studies. The surfactant-polymer solutions were shear thinning in nature, and they followed the power law model. The interaction between the surfactant and polymer had a strong effect on the consistency index of the solution and a marginal effect on the flow behavior index. The surface tension versus surfactant concentration plots were interpreted in terms of the interactions between surfactant and polymer. The critical aggregation concentration (CAC) of the surfactant was estimated based on the surface tension and rheological data. The CAC values of the same charge surfactants as that of the polymer were found to be significantly higher than other combinations of surfactant and polymer, such as non-ionic surfactant/anionic polymer, and zwitterionic surfactant/anionic polymer.

Transport of Polymers in Low Permeability Carbonate Rocks

2021 ◽  
Author(s):  
Haofeng Song ◽  
Pinaki Ghosh ◽  
Kishore Mohanty
Keyword(s):  
Polymer Concentration ◽  
Material Balance ◽  
Economic Feasibility ◽  
Resistance Factor ◽  
Residual Oil ◽  
Residual Resistance ◽  
Oil Saturation ◽  
Residual Oil Saturation ◽  
Polymer Transport ◽  
Residual Resistance Factor

Abstract Polymer transport and retention affect oil recovery and economic feasibility of EOR processes. Most studies on polymer transport have focused on sandstones with permeabilities (k) higher than 200 mD. A limited number of studies were conducted in carbonates with k less than 100 mD and very few in the presence of residual oil. In this work, transport of four polymers with different molecular weights (MW) and functional groups are studied in Edwards Yellow outcrop cores (k<50 mD) with and without residual oil saturation (Sor). The retention of polymers was estimated by both the material balance method and the double-bank method. The polymer concentration was measured by both the total organic carbon (TOC) analyzer and the capillary tube rheology. Partially hydrolyzed acrylamide (HPAM) polymers exhibited high retention (> 150 μg/g), inaccessible pore volume (IPV) greater than 7%, and high residual resistance factor (>9). A sulfonated polyacrylamide (AN132), showed low retentions (< 20 μg/g) and low IPV. The residual resistance factor (RRF) of AN132 in the water-saturated rock was less than 2, indicating little blocking of pore throats in these tight rocks. The retention and RRF of the AN132 polymer increased in the presence of residual oil saturation due to partial blocking of the smaller pore throats available for polymer propagation in an oil-wet core.

Some Aspects of Polymer Retention in Porous Media Using a C14-Tagged Hydrolyzed Polyacrylamide

1975 ◽  
Vol 15 (04) ◽  
pp. 323-337 ◽  
Author(s):  
M.T. Szabo
Keyword(s):  
Porous Media ◽  
Oil Recovery ◽  
Pore Volume ◽  
Produced Water ◽  
Polymer Concentration ◽  
Oil Saturation ◽  
Polymer Flow ◽  
Hydrolyzed Polyacrylamide ◽  
Polymer Retention ◽  
Inaccessible Pore Volume

Abstract Numerous single-phase flow and oil-recovery tests were carried out in unconsolidated sands and Berea sandstone cores using C14-tagged, hydrolyzed polyacrylamide solutions. The polymer-retention polyacrylamide solutions. The polymer-retention data from these flow tests are compared with data obtained from static adsorption tests. Polymer concentrations in produced water in Polymer-flooding tests were studied using various Polymer-flooding tests were studied using various polymer concentrations, slug sizes, salt polymer concentrations, slug sizes, salt concentrations, and different permeability sands. Results show that polymer retention by mechanical entrapment had a dominant role in determining the total polymer retention in short sand packs. However, the role of mechanical entrapment was less in the large-surface-area Berea cores. In oil-recovery tests, high polymer concentrations were noted at water breakthrough in sand-pack experiments, an indication that the irreducible water was not displaced effectively ahead of the polymer slug. However, in similar tests with Berea cores, a denuded zone developed at the leading edge of the polymer slug. polymer slug. The existence of inaccessible pore volume to polymer flow is shown both in sand packs and in polymer flow is shown both in sand packs and in sandstone cores. Absolute polymer-retention values show an almost linear dependency on polymer concentration. The effect of polymer slug size on absolute polymer retention is also discussed. Distribution of retained polymer in sand packs showed an exponential decline with distance. The "dynamic polymer-retention" values in short sand packs showed much higher vales than the ‘static packs showed much higher vales than the’ static polymer-adsorption" values caused by mechanical polymer-adsorption" values caused by mechanical entrapment. The mechanism of polymer retention in silica sands and sandstones is described, based on the observed phenomenon. Introduction It is widely recognized that, as polymer solution flows in a porous medium, a portion of the polymer is retained. It is evident that both physical adsorption and mechanical entrapment contribute to polymer retention. The question of the relative importance of these retention mechanisms has not been studied adequately. The effect of residual oil saturation on polymer retention and the polymer retention during the displacement of oil from porous media has also been studied inadequately. Mungen et al. have reported a few data on polymer concentration in produced water in oil-recovery tests. However, no produced water in oil-recovery tests. However, no comparison was made between polymer retention at 100-percent water saturation and at partial oil saturation. It has been shown that the actual size of the flowing polymer molecules, with the associated water, can approach the dimensions of certain smaller pores found in porous media. Therefore, an inaccessible pore volume exists in which no polymer flow occurs. In this study, the existence polymer flow occurs. In this study, the existence of inaccessible pore volume is shown clearly, both in sand and sandstone. Although polymer-retention values have been reported for various conditions, correlation is difficult because of the differing conditions of measurements. The effect of slug size, polymer concentration, salinity, and type of porous media on polymer retention has not been systematically studied. The purpose of this study was to develop answers to these questions, rather than to provide adsorption data for actual field core samples. For this reason, unconsolidated silica sands were used in most of the experiments reported. This permitted identical, uniform single-layer and multilayer porous media to be constructed for repeated experiments under varying test conditions. Some experiments were also carried out in Berea sandstone cores to determine whether sand-pack results can be extrapolated to consolidated sandstones. Using a C 14-tagged polymer provided a very rapid, simple, and accurate polymer-concentration determination technique. SPEJ P. 323

Effect of Concentration on HPAM Retention in Porous Media

SPE Journal ◽  
2014 ◽  
Vol 19 (03) ◽  
pp. 373-380 ◽  
Author(s):  
Guoyin Zhang ◽  
R.S.. S. Seright
Keyword(s):  
Porous Medium ◽  
Porous Media ◽  
Polymer Solution ◽  
Polymer Concentration ◽  
Retention Mechanism ◽  
Dynamic Measurements ◽  
Polymer Molecules ◽  
Adsorbed Polymer ◽  
Hydrolyzed Polyacrylamide ◽  
Polymer Retention

Summary This paper investigates the effect of hydrolyzed polyacrylamide (HPAM) polymer concentration on retention in porous media by use of both static and dynamic measurements. Consistent results by use of these two methods show that different polymer-retention behaviors exist in dilute, semidilute, and concentrated regions. In both the dilute and concentrated regions, polymer retention has little dependence on concentration. In contrast, in the semidilute region, polymer retention is concentration dependent. If a porous medium is first contacted sufficiently with dilute polymer solution to satisfy the retention, no significant additional retention occurs during exposure to higher HPAM concentrations. On the basis of the experimental results, a concentration-related retention mechanism is proposed that considers the orientation of the adsorbed polymer molecules and the interaction between molecular coils in solution. By use of this model, we explain why polymer retention does not show much dependence on concentration in the dilute and concentrated regimes. Further, in the semidilute region, we explain how moderate coil interactions lead to mixed adsorbed-polymer orientation and magnitude on rock surfaces, and retention becomes concentration dependent. In field applications of polymer and chemical floods, reduced polymer retention may be achieved by first injecting a low-concentration polymer bank.

Flow Behavior Through Porous Media and Microdisplacement Performances of Hydrophobically Modified Partially Hydrolyzed Polyacrylamide

SPE Journal ◽  
2016 ◽  
Vol 21 (03) ◽  
pp. 688-705 ◽  
Author(s):  
Yongjun Guo ◽  
Jun Hu ◽  
Xinmin Zhang ◽  
Rusen Feng ◽  
Huabing Li
Keyword(s):  
Pore Size ◽  
Flow Behavior ◽  
Polymer Concentration ◽  
Molecular Structures ◽  
Microporous Membranes ◽  
Series Connection ◽  
Partially Hydrolyzed Polyacrylamide ◽  
Hydrophobically Modified ◽  
Monomer Content ◽  
Hydrolyzed Polyacrylamide

Summary To investigate the relationship between the flow behavior and microdisplacement performance and the molecular structures, especially associating monomer content, of hydrophobically modified partially hydrolyzed polyacrylamides (HMHPAMs) with varied associating monomer content, compared with that of partially hydrolyzed polyacrylamide (HPAM), a series of experiments were conducted that involved the filtration through screen viscometer, nucleopore membrane, and series-connection microporous membranes; the flow through three serial mounted artificial cores; and the displacement in the microetching model. The screen factors and the hydrodynamic sizes of polymers were obtained by screen viscometer and nucleopore membrane, respectively. The results show that the screen factors and hydrodynamic sizes of HMHPAMs were much-more sensitive to the polymer concentration, filtration pressure, and associating monomer content than HPAM. Moreover, the filtration experiment through series-connection microporous membranes indicates that there were moderate associating monomer content or greater flow pressure or pore size for HMHPAMs to easily pass and obtain equivalent differential pressure between membranes, which implies that the compatibility between the pore size and the hydrodynamic sizes of the microstructures is the most-important factor for the injectivity of HMHPAMs. The resistance factor (RF) established by HMHPAMs through three serial mounted artificial cores notably tended to be higher than HPAMs, and the HMHPAMs with higher associating monomer content could generate a greater RF. In contrast, when the associating monomer content was low enough and the permeability was high enough, the flow could obtain equilibrium easily and the RFs were almost in accordance, which indicate there was moderate associating monomer content for HMHPAMs to propagate deep into the cores. At the same viscosity, HMHPAMs had better microdisplacement efficiency than glycerol (no effect) and HPAM (a small portion) for displacing the residual oil trapped in the “dead” ends of flow channel. The pilot tests of the associative polymer AP-P4, which was developed for Bohai oil fields, have demonstrated the great application potential of HMHPAMs for enhanced oil recovery (EOR).

Retention and Flow Characteristics of Polymer Solutions in Porous Media

1977 ◽  
Vol 17 (02) ◽  
pp. 111-121 ◽  
Author(s):  
J.G. Dominguez ◽  
G.P. Willhite
Keyword(s):  
Porous Media ◽  
Flow Rate ◽  
Polymer Solutions ◽  
Polymer Concentration ◽  
Flow Characteristics ◽  
Porous Matrix ◽  
Polymer Molecules ◽  
Partially Hydrolyzed Polyacrylamide ◽  
Hydrolyzed Polyacrylamide ◽  
Polymer Retention

Abstract Retention and flow characteristics of a solution containing Pusher 700, a high-molecular-weight, partially hydrolyzed polyacrylamide, were studied partially hydrolyzed polyacrylamide, were studied in an 86-md core made by compacting Teflon powder. The quantity, of polymer retained during linear displacement experiments ranged from 10 to 21 mu gm/gm for polymer concentrations of 100 to 500 ppm in 2-percent NaCl solutions. Nearly all retention ppm in 2-percent NaCl solutions. Nearly all retention was attributed to mechanical entrapment because of low polymer adsorption on the Teflon surface. Flow rate affected polymer retention. In increase in velocity was accompanied by polymer retention. Polymer was expelled when the flow rate was Polymer was expelled when the flow rate was reduced. Inaccessible pore volume was about 19 percent of the total pore volume. percent of the total pore volume.Resistance factors in different sections of the core ranged Pam 2 to 10 /or solutions of 100 to 500 ppm polymer concentration in 2-percent NaCl. ppm polymer concentration in 2-percent NaCl. Permeability reduction resulting from polymer Permeability reduction resulting from polymer retention produces the resistance factor in most of the core at a velocity of 3.2 ft/D. Resistance factors in the Teflon cores were two to three times lower than those reported for natural porous media where polymer is also retained by adsorption. Introduction The search for a low-cost, effective mobility control agent is currently focused on dilute aqueous solutions containing partially hydrolyzed polyacrylamides or polysaccharides. Rheological polyacrylamides or polysaccharides. Rheological properties have been studied, including the properties have been studied, including the effects of polymer concentration, shear rate, electrolyte concentration, and type of electrolyte. Correlation of rheological data and models with the flow behavior of polymer solutions in porous media has been complicated by the many interactions that occur between the complex porous matrix and the polymer solutions. Some data have been correlated using non-Newtonian rheological models to describe the variation of fluid viscosity with the apparent shear rate that the fluid experiences as it flows through the tortuous paths in porous media. These correlations have adjustable parameters determined from the particular set of parameters determined from the particular set of data used to develop the correlation. Investigators studying partially hydrolyzed polyacrylamide solutions observed apparent polyacrylamide solutions observed apparent viscosities 5 to 20 times the values measured in a conventional viscometer at the shear rates believed to exist in the porous media. These viscosity increases were not anticipated from the rheological behavior of the fluids. Pye introduced the concept of the resistance factor to quantify this effect. Burcik observed a decrease in the mobility of brine in a Berea sandstone disk that had been previously contacted with partially hydrolyzed previously contacted with partially hydrolyzed polyacrylamide. The mobility reduction persisted polyacrylamide. The mobility reduction persisted even after 100 PV of brine had been flushed through the disk. Burcik concluded that polymer molecules retained in the pore structure by adsorption or mechanical entrapment were hydrophillic and restricted the flow of water. Gogarty made an extensive experimental study of partially hydrolyzed polyacrylamide solutions in porous media and concluded that these polymer porous media and concluded that these polymer solutions reduced the permeability of the porous media. He noosed that polymer retention in natural cores occurred by mechanical entrapment and adsorption. Both mechanisms contributed to the resistance and residual or flushed resistance factors observed with polyacrylamide solutions. Other evidence of interactions between the polymer solution and the porous matrix was found. polymer solution and the porous matrix was found. Adsorption of polymer molecules on the surface of materials present in the porous matrix has been demonstrated in batch adsorption experiments. Material-balance calculations made on the streams entering and leaving porous media following step changes in concentrations show retention of polymer molecules in the porous media. polymer molecules in the porous media. A dependence of polymer retention on flow rate has been reported. Szabo devised a set of static and flow experiments in which polymer adsorption was held to a low level by using silica sand with a small surface area. Mechanical entrapment was found to be the dominant retention mechanism in short sand packs. packs. SPEJ P. 111

scholarly journals Effect of Polymer Adsorption on Permeability Reduction in Enhanced Oil Recovery

2014 ◽  
Vol 2014 ◽  
pp. 1-9 ◽  
Author(s):  
Saurabh Mishra ◽  
Achinta Bera ◽  
Ajay Mandal
Keyword(s):  
Oil Recovery ◽  
Polymer Concentration ◽  
Polymer Adsorption ◽  
Mobility Control ◽  
Special Focus ◽  
Permeability Reduction ◽  
Solution Ph ◽  
Residual Resistance ◽  
Polymer Injection ◽  
Hydrolyzed Polyacrylamide

In order to reduce the permeability to water or brine, there is a possibility of polymer injection into the reservoir. In the present work, special focus has been paid in polymer [partially hydrolyzed polyacrylamide (PHPA)] injection as a part of chemical method. Tests were conducted in the laboratory at the ambient temperature to examine the reduction in permeability to water or brine in the well-prepared sand packed after the polymer injection. The experiments were performed to study the effect of polymer adsorption on permeability reduction by analyzing residual resistance factor values with different concentrations of polymer solutions. The rheological behavior of the polymer has also been examined. The experimental results also indicate that the adsorption behavior of polymer is strongly affected by salinity, solution pH, and polymer concentration. To investigate the effect of polymer adsorption and mobility control on additional oil recovery, polymer flooding experiments were conducted with different polymer concentrations. It has been obtained that with the increase in polymer concentrations, oil recovery increases.

Sign in / Sign up

Export Citation Format

Share Document