scholarly journals Performance Analysis of Wind-Induced Piezoelectric Vibration Bimorph Cantilever for Rotating Machinery

2015 ◽  
Vol 2015 ◽  
pp. 1-10 ◽  
Author(s):  
Gongbo Zhou ◽  
Houlian Wang ◽  
Zhencai Zhu ◽  
Linghua Huang ◽  
Wei Li
Keyword(s):  
Cantilever Beam ◽  
Output Voltage ◽  
Theory Model ◽  
Rotating Machinery ◽  
Response Analysis ◽  
Maximum Output ◽  
Piezoelectric Bimorph ◽  
Resonant Condition ◽  
Harmonic Response Analysis ◽  
Piezoelectric Vibration

Harvesting the energy contained in the running environment of rotating machinery would be a good way to supplement energy to the wireless sensor. In this paper, we take piezoelectric bimorph cantilever beam with parallel connection mode as energy collector and analyze the factors which can influence the generation performance. First, a modal response theory model is built. Second, the static analysis, modal analysis, and piezoelectric harmonic response analysis of the wind-induced piezoelectric bimorph cantilever beam are given in detail. Finally, an experiment is also conducted. The results show that wind-induced piezoelectric bimorph cantilever beam has low resonant frequency and stable output under the first modal mode and can achieve the maximum output voltage under the resonant condition. The output voltage increases with the increase of the length and width of wind-induced piezoelectric bimorph cantilever beam, but the latter increasing amplitude is relatively smaller. In addition, the output voltage decreases with the increase of the thickness and the ratio of metal substrate to piezoelectric patches thickness. The experiment showed that the voltage amplitude generated by the piezoelectric bimorph cantilever beam can reach the value simulated in ANSYS, which is suitable for actual working conditions.

Power Harvesting for Rotating Structure Using Piezoelectric Generators

2006 ◽  
Author(s):  
Saurav Gupta ◽  
Grant M. Warner
Keyword(s):  
Cantilever Beam ◽  
Piezoelectric Materials ◽  
Ring System ◽  
Rotating Machinery ◽  
Piezoelectric Bimorph ◽  
Mems Sensors ◽  
Power Harvesting ◽  
Slip Ring ◽  
Sensor Signals ◽  
Rotating Structure

Conventional method of measuring the mechanical properties of rotating machinery is to couple sensors on the machine through a slip ring, which is a non-trivial, expensive, lengthy and manpower intensive process. An alternative to this is to use a contactless RF slip ring which has no physical wear and hence no maintenance. But application of contactless RF slip ring is possible only if these services are low powered and sensor signals can be multiplexed. With the advance in low powered MEMS sensors, contactless slip ring system can be used. But providing power to these sensors is an issue. One approach would be to harness power from the untapped surrounding energy which could be used to recharge and/or replace battery powered connections. One method to accomplish this is to use piezoelectric materials (PZT) to capture energy lost due to vibration and rotation of the test equipment. This captured energy can then be used to provide uninterrupted power to the appropriate sensors. Focusing our attention on blades, rotating structures will be modeled as cantilever beam. Piezoelectric bimorph attached to the rotating cantilever beam will provide an estimate for the available power that can be used for harvesting.

Novel Low-Frequency Rectangular-Loop Piezoelectric Energy Harvester

2014 ◽  
Vol 635-637 ◽  
pp. 928-931
Author(s):  
Shuai Yuan ◽  
Bing Jiang ◽  
Li Juan Chen ◽  
Yu Guo Hao ◽  
Jian Bo Xin ◽  
...  
Keyword(s):  
Resonant Frequency ◽  
Output Voltage ◽  
Energy Harvester ◽  
Low Frequency ◽  
Effective Bandwidth ◽  
Response Analysis ◽  
Element Analysis ◽  
Piezoelectric Energy ◽  
The Finite Element Analysis ◽  
Harmonic Response Analysis

The ambient energy harvesting based on piezoelectric has become an important subject in recent research publications. A new rectangular-loop piezoelectric energy harvester(RLPEH) is proposed. The characteristic is analyzed by the finite element analysis (FEA) which includes the static analysis, modal analysis and harmonic response analysis. The analysis results show that the RLPEH could reduce the resonant frequency and improve the output voltage. The three order resonant frequency is 18.6Hz, 40.8Hz and 85.4Hz. The output voltage is 42V under 3m/s2 of acceleration and the effective bandwidth is 18.7Hz with output voltage above 10V.

Design of a Unique Unimorph and Bimorph Cantilever Energy Harvesting System

2020 ◽  
Vol 12 (4) ◽  
pp. 506-512
Author(s):  
Ashok Batra ◽  
Almuatasim Alomari ◽  
James Sampson ◽  
Alak Bandyopadhyay ◽  
Mohan Aggarwal
Keyword(s):  
Resonant Frequency ◽  
Energy Conversion ◽  
Cantilever Beam ◽  
Output Voltage ◽  
Electromechanical Coupling ◽  
Energy Harvester ◽  
Piezoelectric Element ◽  
Maximum Output ◽  
Element Analysis ◽  
Piezoelectric Energy

Piezoelectric energy conversion has received considerable attention for vibration-to-electric energy conversion over the past decade. A typical piezoelectric energy harvester is a unimorph or a bimorph cantilever located on a vibrating host structure. This paper presents a comparison between unimorph and bimorph cantilever beam having a number of segmented PMN-PT piezo-elements on the input and output power. The numerical simulation was carried out by applying the finite element analysis (FEA) using COMSOL multi-physics software in order to predict output voltage and power over a frequency range of 60–200 Hz for the first resonant frequencies. The simulation results show maximum output voltage and power harvested of 7.38 V and 135.73 μW, respectively, by the unimorph piezoelectric energy harvester at resonant frequency value of 84 Hz with electromechanical coupling factor (ke) of 77.29%. These results highlight that the highest value of the output electrical power can be obtained when the piezoelectric element is attached on the top of a clamped end of a cantilever piezoelectric beam. Moreover, in an unimorph or bimorph cantilever beam system, increasing the number of piezoelectric elements results in a higher resonant frequency shift and significantly decreasing in the harvested power.

Harmonic Response Analysis of Rotor-Rolling Bearing-Base System for Fault Diagnosis of Rotating Machinery Based on Base

2011 ◽  
Vol 143-144 ◽  
pp. 669-674
Author(s):  
B. Qin ◽  
J.G. Wu ◽  
X.J. Li ◽  
B.H. Yao
Keyword(s):  
Fault Diagnosis ◽  
Condition Monitoring ◽  
Vibration Signal ◽  
Rolling Bearing ◽  
Rotating Machinery ◽  
Response Analysis ◽  
Base System ◽  
Test Bed ◽  
Harmonic Response ◽  
Harmonic Response Analysis

In the fault diagnosis of rotating machinery through vibration analysis of the base, the signal may be weak and impure since the vibration signal which collected at the base is far away from the fault source. In order to provide useful evidences for the condition monitoring and fault diagnosis of rolling bearing based on the base vibration signal analysis, the rotor-bearing-base system model is built by taking the Spectra Quest comprehensive fault simulation test-bed as the object, the harmonic response analysis of the entire system is done with finite element analysis software ANSYS, and the ideal locations where sensors are installed on the base are obtained. These will form the foundation for the condition monitoring and fault diagnosis of rolling bearing based on the base vibration signal.

Design and Simulation of Piezoelectric Bimorph Cantilever Beam

2019 ◽  
Author(s):  
Nitesh Dixit ◽  
Amit Kumar Saraf ◽  
Dr. MP Singh
Keyword(s):  
Cantilever Beam ◽  
Piezoelectric Bimorph

scholarly journals A Dual Frequency Ultrasonic Cleaning Tank Developed by Transient Dynamic Analysis

2021 ◽  
Vol 11 (2) ◽  
pp. 699
Author(s):  
Worapol Tangsopa ◽  
Jatuporn Thongsri
Keyword(s):  
High Performance ◽  
Acoustic Pressure ◽  
Single Frequency ◽  
Response Analysis ◽  
Dual Frequency ◽  
Transient Dynamic Analysis ◽  
Ultrasonic Cleaning ◽  
Calculational Method ◽  
Successful Design ◽  
Harmonic Response Analysis

At present, development of manufacturer’s ultrasonic cleaning tank (UCT) to match the requirements from consumers usually relies on computer simulation based on harmonic response analysis (HRA). However, this technique can only be used with single-frequency UCT. For dual frequency, the manufacturer used information from empirical experiment alongside trial-and-error methods to develop prototypes, resulting in the UCT that may not be fully efficient. Thus, lack of such a proper calculational method to develop the dual frequency UCT was a problem that greatly impacted the manufacturers and consumers. To resolve this problem, we proposed a new model of simulation using transient dynamics analysis (TDA) which was successfully applied to develop the prototype of dual frequency UCT, 400 W, 18 L in capacity, eight horn transducers, 28 and 40 kHz frequencies for manufacturing. The TDA can indicate the acoustic pressure at all positions inside the UCT in transient states from the start to the states ready for proper cleaning. The calculation also reveals the correlation between the positions of acoustic pressure and the placement positions of transducers and frequencies. In comparison with the HRA at 28 kHz UCT, this TDA yielded the results more accurately than the HRA simulation, comparing to the experiments. Furthermore, the TDA can also be applied to the multifrequency UCTs as well. In this article, the step-by-step development of methodology was reported. Finally, this simulation can lead to the successful design of the high-performance dual frequencies UCT for the manufacturers.

scholarly journals Theoretical and Experimental Studies on MEMS Variable Cross-Section Cantilever Beam Based Piezoelectric Vibration Energy Harvester

Micromachines ◽  
2021 ◽  
Vol 12 (7) ◽  
pp. 772
Author(s):  
Xianming He ◽  
Dongxiao Li ◽  
Hong Zhou ◽  
Xindan Hui ◽  
Xiaojing Mu
Keyword(s):  
Power Density ◽  
Cantilever Beam ◽  
Cross Section ◽  
Energy Harvester ◽  
Variable Cross Section ◽  
Vibration Energy ◽  
Variable Cross ◽  
Vibration Energy Harvester ◽  
Piezoelectric Vibration Energy Harvester ◽  
Piezoelectric Vibration

The piezoelectric vibration energy harvester (PVEH) based on the variable cross-section cantilever beam (VCSCB) structure has the advantages of uniform axial strain distribution and high output power density, so it has become a research hotspot of the PVEH. However, its electromechanical model needs to be further studied. In this paper, the bidirectional coupled distributed parameter electromechanical model of the MEMS VCSCB based PVEH is constructed, analytically solved, and verified, which laid an important theoretical foundation for structural design and optimization, performance improvement, and output prediction of the PVEH. Based on the constructed model, the output performances of five kinds of VCSCB based PVEHs with different cross-sectional shapes were compared and analyzed. The results show that the PVEH with the concave quadratic beam shape has the best output due to the uniform surface stress distribution. Additionally, the influence of the main structural parameters of the MEMS trapezoidal cantilever beam (TCB) based PVEH on the output performance of the device is theoretically analyzed. Finally, a prototype of the Aluminum Nitride (AlN) TCB based PVEH is designed and developed. The peak open-circuit voltage and normalized power density of the device can reach 5.64 V and 742 μW/cm3/g2, which is in good agreement with the theoretical model value. The prototype has wide application prospects in the power supply of the wireless sensor network node such as the structural health monitoring system and the Internet of Things.

Dynamic Analysis of DVG 850 High-Speed Machining Center

2012 ◽  
Vol 487 ◽  
pp. 203-207
Author(s):  
Gong Xue Zhang ◽  
Xiao Kai Shen
Keyword(s):  
High Speed ◽  
Simulation Analysis ◽  
Response Analysis ◽  
Improved Method ◽  
Analysis Software ◽  
Element Analysis ◽  
Harmonic Response ◽  
Machining Center ◽  
Calculation Results ◽  
Harmonic Response Analysis

Purpose, with the application of workbench finite element analysis software, get the analysis results of DVG 850 high-speed vertical machining center via the modal analysis and harmonic response analysis. Use the calculation results for reference, put forward the improved method, and prove the credibility of the simulation analysis by testing DVG 850 prototype.

scholarly journals Analytical Modeling of a Doubly Clamped Flexible Piezoelectric Energy Harvester with Axial Excitation and Its Experimental Characterization

Sensors ◽  
2021 ◽  
Vol 21 (11) ◽  
pp. 3861
Author(s):  
Jie Mei ◽  
Qiong Fan ◽  
Lijie Li ◽  
Dingfang Chen ◽  
Lin Xu ◽  
...  
Keyword(s):  
Output Power ◽  
Power Output ◽  
Output Voltage ◽  
Energy Harvester ◽  
Load Resistance ◽  
Engineering Practice ◽  
Maximum Output ◽  
Widespread Application ◽  
Piezoelectric Energy ◽  
Axial Excitation

With the rapid development of wearable electronics, novel power solutions are required to adapt to flexible surfaces for widespread applications, thus flexible energy harvesters have been extensively studied for their flexibility and stretchability. However, poor power output and insufficient sensitivity to environmental changes limit its widespread application in engineering practice. A doubly clamped flexible piezoelectric energy harvester (FPEH) with axial excitation is therefore proposed for higher power output in a low-frequency vibration environment. Combining the Euler–Bernoulli beam theory and the D’Alembert principle, the differential dynamic equation of the doubly clamped energy harvester is derived, in which the excitation mode of axial load with pre-deformation is considered. A numerical solution of voltage amplitude and average power is obtained using the Rayleigh–Ritz method. Output power of 22.5 μW at 27.1 Hz, with the optimal load resistance being 1 MΩ, is determined by the frequency sweeping analysis. In order to power electronic devices, the converted alternating electric energy should be rectified into direct current energy. By connecting to the MDA2500 standard rectified electric bridge, a rectified DC output voltage across the 1 MΩ load resistor is characterized to be 2.39 V. For further validation of the mechanical-electrical dynamical model of the doubly clamped flexible piezoelectric energy harvester, its output performances, including both its frequency response and resistance load matching performances, are experimentally characterized. From the experimental results, the maximum output power is 1.38 μW, with a load resistance of 5.7 MΩ at 27 Hz, and the rectified DC output voltage reaches 1.84 V, which shows coincidence with simulation results and is proved to be sufficient for powering LED electronics.

Sign in / Sign up

Export Citation Format

Share Document