scholarly journals Experimental Thermal Analysis of Diesel Engine Piston and Cylinder Wall

2015 ◽  
Vol 2015 ◽  
pp. 1-10 ◽  
Author(s):  
Subodh Kumar Sharma ◽  
P. K. Saini ◽  
N. K. Samria
Keyword(s):  
Heat Transfer ◽  
Diesel Engine ◽  
Wall Temperature ◽  
Thermal Loading ◽  
Thermal Stresses ◽  
Transfer Model ◽  
Cylinder Wall ◽  
Fe Model ◽  
Transfer Coefficients ◽  
Thermocouple Wire

Knowledge of piston and cylinder wall temperature is necessary to estimate the thermal stresses at different points; this gives an idea to the designer to take care of weaker cross section area. Along with that, this temperature also allows the calculation of heat losses through piston and cylinder wall. The proposed methodology has been successfully applied to a water-cooled four-stroke direct-injection diesel engine and it allows the estimation of the piston and cylinder wall temperature. The methodology described here combines numerical simulations based on FEM models and experimental procedures based on the use of thermocouples. Purposes of this investigation are to measure the distortion in the piston, temperature, and radial thermal stresses after thermal loading. To check the validity of the heat transfer model, measure the temperature through direct measurement using thermocouple wire at several points on the piston and cylinder wall. In order to prevent thermocouple wire entanglement, a suitable pathway was designed. Appropriate averaged thermal boundary conditions such as heat transfer coefficients were set on different surfaces for FE model. The study includes the effects of the thermal conductivity of the material of piston, piston rings, and combustion chamber wall. Results show variation of temperature, stresses, and deformation at various points on the piston.

scholarly journals FINITE ELEMENT ANALYSIS OF THE HEAT TRANSFER IN A PISTON

2020 ◽  
Vol 4 (1) ◽  
pp. 45-51
Author(s):  
Aisha Muhammad ◽  
Shanono Ibrahim Haruna
Keyword(s):  
Heat Transfer ◽  
Finite Element ◽  
Numerical Simulations ◽  
Internal Combustion Engines ◽  
Thermal Stresses ◽  
Maximum Temperature ◽  
Cylinder Wall ◽  
Fe Model ◽  
Piston Cylinder ◽  
Piston Head

The gas expansion process that takes place in a piston cylinder assembly have been used in numerous applications. However, the time-dependent process of heat transfer is still not fully apprehended as the expansion processes are complex and difficult due to the unsteady property of the turbulent flow process. Internal combustion Engines(ICE) designs are conducted with the aim of achieving higher efficiency in the thermal characteristics. To optimize these designs, numerical simulations are conducted. However, modelling of the process in terms of heat transfer and combustion is complex and challenging. For a designer to understand, calculate and quantify the thermal stresses and heat losses at different sections of the structure, understanding the piston-cylinder wall is needed. This study carried out a numerical simulations based on Finite Element Method (FEM) to investigatethe stresses in the piston, and temperature after loading. Appropriate boundary conditions were set on different surfaces for FE model. The study includes the effects of the thermal conductivity of the material of piston, cylinder wall, and connecting rod. Results show the maximum Von-misses stress occurs on the piston head with a value of 3486. 1MPa. The maximum temperature of the piston head and cylinder wall stands at 68.252 and 42.704 degree Celsius respectively.

scholarly journals Heat Transfer in Rotating Serpentine Passages With Trips Normal to the Flow

1992 ◽  
Vol 114 (4) ◽  
pp. 847-857 ◽  
Author(s):  
J. H. Wagner ◽  
B. V. Johnson ◽  
R. A. Graziani ◽  
F. C. Yeh
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Large Scale ◽  
Flow Direction ◽  
Operating Conditions ◽  
Transfer Model ◽  
Transfer Coefficients ◽  
Flow Equations ◽  
Turbine Blade Cooling ◽  
Heat Transfer Coefficients

Experiments were conducted to determine the effects of buoyancy and Coriolis forces on heat transfer in turbine blade internal coolant passages. The experiments were conducted with a large-scale, multipass, heat transfer model with both radially inward and outward flow. Trip strips on the leading and trailing surfaces of the radial coolant passages were used to produce the rough walls. An analysis of the governing flow equations showed that four parameters influence the heat transfer in rotating passages: coolant-to-wall temperature ratio, Rossby number, Reynolds number, and radius-to-passage hydraulic diameter ratio. The first three of these four parameters were varied over ranges that are typical of advanced gas turbine engine operating conditions. Results were correlated and compared to previous results from stationary and rotating similar models with trip strips. The heat transfer coefficients on surfaces, where the heat transfer increased with rotation and buoyancy, varied by as much as a factor of four. Maximum values of the heat transfer coefficients with high rotation were only slightly above the highest levels obtained with the smooth wall model. The heat transfer coefficients on surfaces where the heat transfer decreased with rotation, varied by as much as a factor of three due to rotation and buoyancy. It was concluded that both Coriolis and buoyancy effects must be considered in turbine blade cooling designs with trip strips and that the effects of rotation were markedly different depending upon the flow direction.

The Infrared Characteristics of the Wall Temperature of Boiling Heat Transfer in Microchannel

2011 ◽  
Vol 383-390 ◽  
pp. 811-815
Author(s):  
Hu Gen Ma ◽  
Jian Mei Bai ◽  
Rong Jian Xie ◽  
Wen Jing Tu
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Wall Temperature ◽  
Boiling Heat Transfer ◽  
Transfer Test ◽  
Axial Direction ◽  
Transfer Model ◽  
Micro Channel ◽  
Vapor Quality ◽  
Test Rig

In this paper, the boiling heat transfer test rig was designed and built, while the characteristics of boiling Heat Transfer of refrigerants in micro-channel was researched. The wall temperature of micro-channel was measured by TH5104 Infrared thermography. The results showed that there were obvious variations for wall temperature of micro-channel along the axial direction when boiling heat transfer occurred in the micro-channel. The temperature distribution affected obviously by the heat flux, mass flow rate; vapor quality and heat transfer model.

Comparison of Existing Supercritical Carbon Dioxide Heat Transfer Correlations for Horizontal and Vertical Bare Tubes

2012 ◽  
Author(s):  
Prabu Surendran ◽  
Sahil Gupta ◽  
Tiberiu Preda ◽  
Igor Pioro
Keyword(s):  
Heat Transfer ◽  
Carbon Dioxide ◽  
Supercritical Carbon Dioxide ◽  
Wall Temperature ◽  
Statistical Error ◽  
Heat Fluxes ◽  
Transfer Coefficients ◽  
Bulk Fluid ◽  
Heat Transfer Correlations ◽  
Supercritical Carbon

This paper presents a thorough analysis of ability of various heat transfer correlations to predict wall temperatures and Heat Transfer Coefficients (HTCs) against experiments on internal forced-convective heat transfer to supercritical carbon dioxide conducted by Koppel [1], He [2], Kim [3] and Bae [4]. It should be noted the Koppel dataset was taken from a paper which used the Koppel data but was not written by Koppel. All experiments were completed in bare tubes with diameters from 0.948 mm to 9 mm for horizontal and vertical configurations. The datasets contain a total of 1573 wall temperature points with pressures ranging from 7.58 to 9.59 MPa, mass fluxes of 400 to 1641 kg/m2s and heat fluxes from 20 to 225 kW/m2. The main objective of the study was to compare several correlations and select the best of them in predicting HTC and wall temperature values for supercritical carbon dioxide. This study will be beneficial for analyzing heat exchangers involving supercritical carbon dioxide, and for verifying scaling parameters between CO2 and other fluids. In addition, supercritical carbon dioxide’s use as a modeling fluid is necessary as the costs of experiments are lower than supercritical water. The datasets were compiled and calculations were performed to find HTCs and wall and bulk-fluid temperatures using existing correlations. Calculated results were compared with the experimental ones. The correlations used were Mokry et al. [5], Swenson et al. [6] and a set of new correlations presented in Gutpa et al. [7]. Statistical error calculations were performed are presented in the paper.

Thermal Analysis of Cooling System in a Gas Turbine Transition Piece

2011 ◽  
Author(s):  
Jun Su Park ◽  
Namgeon Yun ◽  
Hokyu Moon ◽  
Kyung Min Kim ◽  
Sin-Ho Kang ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Thermal Stresses ◽  
Cooling System ◽  
Structural Information ◽  
Thermal Analyses ◽  
Thermal Design ◽  
Transfer Coefficients ◽  
Transition Piece ◽  
Inlet Conditions

This paper presents thermal analyses of the cooling system of a transition piece, which is one of the primary hot components in a gas turbine engine. The thermal analyses include heat transfer distributions induced by heat and fluid flow, temperature, and thermal stresses. The purpose of this study is to provide basic thermal and structural information on transition piece, to facilitate their maintenance and repair. The study is carried out primarily by numerical methods, using the commercial software, Fluent and ANSYS. First, the combustion field in a combustion liner with nine fuel nozzles is analyzed to determine the inlet conditions of a transition piece. Using the results of this analysis, pressure distributions inside a transition piece are calculated. The outside of the transition piece in a dump diffuser system is also analyzed. Information on the pressure differences is then used to obtain data on cooling channel flow (one of the methods for cooling a transition piece). The cooling channels have exit holes that function as film-cooling holes. Thermal and flow analyses are carried out on the inside of a film-cooled transition piece. The results are used to investigate the adjacent temperatures and wall heat transfer coefficients inside the transition piece. Overall temperature and thermal stress distributions of the transition piece are obtained. These results will provide a direction to improve thermal design of transition piece.

Measurement and Modeling of Condensation Heat Transfer Coefficients in Circular Microchannels

2006 ◽  
Vol 128 (10) ◽  
pp. 1050-1059 ◽  
Author(s):  
Todd M. Bandhauer ◽  
Akhil Agarwal ◽  
Srinivas Garimella
Keyword(s):  
Heat Transfer ◽  
Flow Rate ◽  
Heat Transfer Model ◽  
Condensation Heat Transfer ◽  
Low Flow ◽  
Transfer Model ◽  
Shear Stresses ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Circular Microchannels

A model for predicting heat transfer during condensation of refrigerant R134a in horizontal microchannels is presented. The thermal amplification technique is used to measure condensation heat transfer coefficients accurately over small increments of refrigerant quality across the vapor-liquid dome (0<x<1). A combination of a high flow rate closed loop primary coolant and a low flow rate open loop secondary coolant ensures the accurate measurement of the small heat duties in these microchannels and the deduction of condensation heat transfer coefficients from measured UA values. Measurements were conducted for three circular microchannels (0.506<Dh<1.524mm) over the mass flux range 150<G<750kg∕m2s. Results from previous work by the authors on condensation flow mechanisms in microchannel geometries were used to interpret the results based on the applicable flow regimes. The heat transfer model is based on the approach originally developed by Traviss, D. P., Rohsenow, W. M., and Baron, A. B., 1973, “Forced-Convection Condensation Inside Tubes: A Heat Transfer Equation For Condenser Design,” ASHRAE Trans., 79(1), pp. 157–165 and Moser, K. W., Webb, R. L., and Na, B., 1998, “A New Equivalent Reynolds Number Model for Condensation in Smooth Tubes,” ASME, J. Heat Transfer, 120(2), pp. 410–417. The multiple-flow-regime model of Garimella, S., Agarwal, A., and Killion, J. D., 2005, “Condensation Pressure Drop in Circular Microchannels,” Heat Transfer Eng., 26(3), pp. 1–8 for predicting condensation pressure drops in microchannels is used to predict the pertinent interfacial shear stresses required in this heat transfer model. The resulting heat transfer model predicts 86% of the data within ±20%.

Experimental Investigation of Heat Transfer in Impingement Air Cooled Plate Fin Heat Sinks

2005 ◽  
Vol 128 (4) ◽  
pp. 412-418 ◽  
Author(s):  
Zhipeng Duan ◽  
Y. S. Muzychka
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Thermal Resistance ◽  
Thermal Performance ◽  
Heat Transfer Model ◽  
Heat Sinks ◽  
Transfer Model ◽  
Transfer Coefficients ◽  
Developing Flow ◽  
Rectangular Channels

Impingement cooling of plate fin heat sinks is examined. Experimental measurements of thermal performance were performed with four heat sinks of various impingement inlet widths, fin spacings, fin heights, and airflow velocities. The percent uncertainty in the measured thermal resistance was a maximum of 2.6% in the validation tests. Using a simple thermal resistance model based on developing laminar flow in rectangular channels, the actual mean heat transfer coefficients are obtained in order to develop a simple heat transfer model for the impingement plate fin heat sink system. The experimental results are combined into a dimensionless correlation for channel average Nusselt number Nu∼f(L*,Pr). We use a dimensionless thermal developing flow length, L*=(L∕2)∕(DhRePr), as the independent parameter. Results show that Nu∼1∕L*, similar to developing flow in parallel channels. The heat transfer model covers the practical operating range of most heat sinks, 0.01<L*<0.18. The accuracy of the heat transfer model was found to be within 11% of the experimental data taken on four heat sinks and other experimental data from the published literature at channel Reynolds numbers less than 1200. The proposed heat transfer model may be used to predict the thermal performance of impingement air cooled plate fin heat sinks for design purposes.

Evaluation of Numerical Methods to Predict Temperature Distributions of an Experimentally Investigated Convection-Cooled Gas-Turbine Blade

2017 ◽  
Author(s):  
E. Findeisen ◽  
B. Woerz ◽  
M. Wieler ◽  
P. Jeschke ◽  
M. Rabs
Keyword(s):  
Heat Transfer ◽  
Numerical Methods ◽  
Gas Turbine ◽  
Turbine Blade ◽  
Gas Turbines ◽  
Cooling System ◽  
Fe Model ◽  
Gas Turbine Blade ◽  
Transfer Coefficients ◽  
Temperature Distributions

This paper presents two different numerical methods to predict the thermal load of a convection-cooled gas-turbine blade under realistic operating temperature conditions. The subject of the investigation is a gas-turbine rotor blade equipped with an academic convection-cooling system and investigated at a cascade test-rig. It consists of three cooling channels, which are connected outside the blade, so allowing cooling air temperature measurements. Both methods use FE models to obtain the temperature distribution of the solid blade. The difference between these methods lies in the generation of the heat transfer coefficients along the cooling channel walls which serve as a boundary condition for the FE model. One method, referred to as the FEM1D method, uses empirical one-dimensional correlations known from the available literature. The other method, the FEM2D method, uses three-dimensional CFD simulations to obtain two-dimensional heat transfer coefficient distributions. The numerical results are compared to each other as well as to experimental data, so that the benefits and limitations of each method can be shown and validated. Overall, this paper provides an evaluation of the different methods which are used to predict temperature distributions in convection-cooled gas-turbines with regard to accuracy, numerical cost and the limitations of each method. The temperature profiles obtained in all methods generally show good agreement with the experiments. However, the more detailed methods produce more accurate results by causing higher numerical costs.

Heat Transfer Enhancement by Turbulent Impinging Jets

2000 ◽  
Author(s):  
M. Kumagai ◽  
R. S. Amano ◽  
M. K. Jensen
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Stokes Equations ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Impinging Jets ◽  
Transfer Model ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients

Abstract A numerical and experimental investigation on cooling of a solid surface was performed by studying the behavior of an impinging jet onto a fixed flat target. The local heat transfer coefficient distributions on a plate with a constant heat flux were computationally investigated with a normally impinging axisymmetric jet for nozzle diameter of 4.6mm at H/d = 4 and 10, with the Reynolds numbers of 10,000 and 40,000. The two-dimensional cylindrical Navier-Stokes equations were solved using a two-equation k-ε turbulence model. The finite-volume differencing scheme was used to solve the thermal and flow fields. The predicted heat transfer coefficients were compared with experimental measurements. A universal function based on the wave equation was developed and applied to the heat transfer model to improve calculated local heat transfer coefficients for short nozzle-to-plate distance (H/d = 4). The differences between H/d = 4 and 10 due to the correlation among heat transfer coefficient, kinetic energy and pressure were investigated for the impingement region. Predictions by the present model show good agreement with the experimental data.

Sign in / Sign up

Export Citation Format

Share Document