scholarly journals Uniform Nonlinear Constitutive Model and Parameters for Clay in Different Consolidation Conditions Based on Regression Method

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Tao Cheng ◽  
Keqin Yan ◽  
Huazhi Zhang ◽  
Xianfeng Luo ◽  
Shengfang Li
Keyword(s):  
Constitutive Model ◽  
Initial Conditions ◽  
Constitutive Relations ◽  
Test Sample ◽  
Maximum Relative Error ◽  
Compression Tests ◽  
Stress Strain ◽  
Strain Behavior ◽  
Nonlinear Constitutive Model ◽  
Isotropic Consolidation

The nonlinear constitutive relations of clay are investigated considering different initial conditions. Highly compressible clay is selected as the test sample. Two groups of tri-axial compression tests are performed, respectively, afterK0consolidation and isotropic consolidation. On the basis of the framework ofE~vmodel, a uniform nonlinear constitutive model is proposed by fitting the test data. With the average slope of the unloading-reloading curve selected as the unloading modulus, the unloading function is constructed as the loading-unloading criterion. Moreover, a comparison between the experimental stress-strain curves and the results predicted by the constitutive model is made. It is shown that the prediction is reasonable, which can reflect the stress-strain behavior of the soil under theK0consolidation and isotropic consolidation conditions. The maximum relative error of the two series of curves is not remarkable, less than 6%.

Numerical Simulation for the Deformation of Composite Wall Insulation System

2011 ◽  
Vol 374-377 ◽  
pp. 187-190
Author(s):  
Tao Cheng
Keyword(s):  
Constitutive Model ◽  
Triaxial Compression ◽  
Constitutive Relations ◽  
Compression Tests ◽  
Stress Strain ◽  
Strain Behavior ◽  
Nonlinear Constitutive Model ◽  
Isotropic Consolidation ◽  
Composite Wall ◽  
Triaxial Compression Tests

The nonlinear constitutive relations of clay are investigated with different initial stress conditions. Two series of triaxial compression tests are performed, respectively after consolidation and isotropic consolidation. On the basis of the framework of ~ model, a uniform nonlinear constitutive model is proposed by fitting of the test data. With the average slope of the unloading-reloading curve selected as the unloading modulus, the unloading function is constructed as the loading-unloading criterion. Moreover, a comparison of the experimental stress-strain curves with the predicted results by the constitutive model is made. It is shown that the model prediction is reasonable, which can reflect the stress-strain behavior of the soil under the consolidation and isotropic consolidation conditions.

Nonlinear Constitutive Model for Clay on K0 Consolidation Conditions

2011 ◽  
Vol 368-373 ◽  
pp. 515-518
Author(s):  
Tao Cheng
Keyword(s):  
Constitutive Model ◽  
Triaxial Compression ◽  
Constitutive Relations ◽  
Compression Tests ◽  
Stress Strain ◽  
Strain Behavior ◽  
Nonlinear Constitutive Model ◽  
Isotropic Consolidation ◽  
Nonlinear Constitutive Relations ◽  
Triaxial Compression Tests

The nonlinear constitutive relations of clay are investigated with different initial stress conditions. Two series of triaxial compression tests are performed, respectively after consolidation and isotropic consolidation. On the basis of the framework of ~ model, a uniform nonlinear constitutive model is proposed by fitting of the test data. With the average slope of the unloading-reloading curve selected as the unloading modulus, the unloading function is constructed as the loading-unloading criterion. Moreover, a comparison of the experimental stress-strain curves with the predicted results by the constitutive model is made. It is shown that the model prediction is reasonable, which can reflect the stress-strain behavior of the soil under the consolidation and isotropic consolidation conditions.

The Constitutive Model for High Temperature Flow Behavior of SiC/6168Al Composite

2015 ◽  
Vol 1089 ◽  
pp. 37-41
Author(s):  
Jiang Wang ◽  
Sheng Li Guo ◽  
Sheng Pu Liu ◽  
Cheng Liu ◽  
Qi Fei Zheng
Keyword(s):  
Constitutive Model ◽  
Hot Deformation ◽  
Flow Behavior ◽  
Type Equation ◽  
Strain Rate Range ◽  
Compression Tests ◽  
Stress Strain ◽  
Hollomon Parameter ◽  
Proposed Model ◽  
Relationship Of

The hot deformation behavior of SiC/6168Al composite was studied by means of hot compression tests in the temperature range of 300-450 °C and strain rate range of 0.01-10 s-1. The constitutive model was developed to predict the stress-strain curves of this composite during hot deformation. This model was established by considering the effect of the strain on material constants calculated by using the Zenter-Hollomon parameter in the hyperbolic Arrhenius-type equation. It was found that the relationship of n, α, Q, lnA and ε could be expressed by a five-order polynomial. The stress-strain curves obtained by this model showed a good agreement with experimental results. The proposed model can accurately describe the hot flow behavior of SiC/6168Al composite, and can be used to numerically analyze the hot forming processes.

Protein Forced Unfolding and Its Effects on the Finite Deformation Stress-Strain Behavior of Biomacromolecular Solids

2005 ◽  
Vol 874 ◽  
Author(s):  
H. Jerry Qi ◽  
Christine Ortiz ◽  
Mary C. Boyce
Keyword(s):  
Constitutive Model ◽  
Single Molecule ◽  
Biological Networks ◽  
Finite Deformation ◽  
State Theory ◽  
Force Extension ◽  
Stress Strain ◽  
Strain Behavior ◽  
Mechanics Model ◽  
Deformation Stress

AbstractMany proteins have been experimentally observed to exhibit a force-extension behavior with a characteristic repeating pattern of a nonlinear rise in force with imposed displacement to a peak, followed by a significant force drop upon reaching the peak (a “saw-tooth” profile) due to successive unfolding of modules during extension. This behavior is speculated to play a governing role in biological and mechanical functions of natural materials and biological networks composed of assemblies of such protein molecules. In this paper, a constitutive model for the finite deformation stress-strain behavior of crosslinked networks of modular macromolecules is developed. The force-extension behavior of the individual modular macromolecule is represented using the Freely Jointed Chain (FJC) statistical mechanics model together with a two-state theory to capture unfolding. The single molecule behavior is then incorporated into a formal continuum mechanics framework to construct a constitutive model. Simulations illustrate a relatively smooth “yield”-like stress-strain behavior of these materials due to activate unfolding in these microstructures.

scholarly journals Effect of Melt Temperature and Hold Pressure on the Weld-Line Strength of an Injection Molded Talc-Filled Polypropylene

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Yuanxin Zhou ◽  
P. K. Mallick
Keyword(s):  
Line Strength ◽  
Weld Line ◽  
Yield Strain ◽  
Stress Strain ◽  
Melt Temperature ◽  
Strain Behavior ◽  
The Core ◽  
Nonlinear Constitutive Model ◽  
Softening Behavior ◽  
Injection Molded

Tensile stress-strain behavior coupled with fractography was used to investigate the weld-line strength of an injection molded 40 w% talc-filled polypropylene. The relationship between processing conditions, microstructure, and tensile strength was established. Fracture surface of the weld line exhibited skin-core morphology with different degrees of talc particle orientations in the core and in the skin. Experimental results also showed that the thickness of the core decreased and the thickness of the skins increased with increasing melt temperature and increasing hold pressure, which resulted in an increase of yield strength and yield strain with increasing melt temperature and increasing hold pressure. Finally, a three-parameter nonlinear constitutive model was developed to describe the strain softening behavior of the weld-line strength of talc-filled polypropylene. The parameters in this model are the modulus E, the strain exponent m, and the compliance factor β. The simulated stress-strain curves from the model are in good agreement with the test data, and both m and β are functions of skin-core thickness ratio.

scholarly journals Stress-Strain Behavior of Perfluorosulfonic Acid Membranes at Various Temperatures and Humidities: Experiments and Phenomenological Modeling

2008 ◽  
Vol 6 (1) ◽  
Author(s):  
Ahmet Kusoglu ◽  
Yaliang Tang ◽  
Michael H. Santare ◽  
Anette M. Karlsson ◽  
Simon Cleghorn ◽  
...  
Keyword(s):  
Constitutive Model ◽  
Flow Behavior ◽  
True Strain ◽  
Plastic Behavior ◽  
Stress Strain ◽  
True Strain Rate ◽  
Material Constants ◽  
Strain Behavior ◽  
Constitutive Response ◽  
Perfluorinated Sulfonic Acid

The constitutive response of perfluorinated sulfonic acid (PFSA) membranes based on tensile testing is investigated, and a phenomenological constitutive model for the elastoplastic flow behavior as a function of temperature and humidity is proposed. To this end, the G’Sell–Jonas (1979, “Determination of the Plastic Behavior of Solid Polymers at Constant True Strain Rate,” J. Mater. Sci., 14, pp. 583–591) constitutive model for semicrystalline polymers is extended by incorporating, in addition to temperature, relationships between the material constants of this model and the measured relative humidity. By matching the proposed constitutive model to the experimental stress-strain data, useful material constants are found. Furthermore, correlations between these material constants and Young’s modulus and proportional limit stress are investigated. The influence of material orientation, inherited from processing conditions, on the stress-strain behavior is also studied. The proposed model can be used to approximate the mechanical behavior of PFSA membranes in numerical simulations of a fuel cell operation.

Development of a Flow Evolution Network Model for the Stress–Strain Behavior of Poly(L-lactide)

2017 ◽  
Vol 139 (9) ◽  
Author(s):  
Maureen L. Dreher ◽  
Srinidhi Nagaraja ◽  
Jorgen Bergstrom ◽  
Danika Hayman
Keyword(s):  
Finite Element ◽  
Constitutive Model ◽  
Computational Modeling ◽  
Medical Devices ◽  
Constitutive Models ◽  
Constitutive Relationship ◽  
Displacement Curve ◽  
Stress Strain ◽  
Strain Behavior ◽  
Flow Evolution

Computational modeling is critical to medical device development and has grown in its utility for predicting device performance. Additionally, there is an increasing trend to use absorbable polymers for the manufacturing of medical devices. However, computational modeling of absorbable devices is hampered by a lack of appropriate constitutive models that capture their viscoelasticity and postyield behavior. The objective of this study was to develop a constitutive model that incorporated viscoplasticity for a common medical absorbable polymer. Microtensile bars of poly(L-lactide) (PLLA) were studied experimentally to evaluate their monotonic, cyclic, unloading, and relaxation behavior as well as rate dependencies under physiological conditions. The data were then fit to a viscoplastic flow evolution network (FEN) constitutive model. PLLA exhibited rate-dependent stress–strain behavior with significant postyield softening and stress relaxation. The FEN model was able to capture these relevant mechanical behaviors well with high accuracy. In addition, the suitability of the FEN model for predicting the stress–strain behavior of PLLA medical devices was investigated using finite element (FE) simulations of nonstandard geometries. The nonstandard geometries chosen were representative of generic PLLA cardiovascular stent subunits. These finite element simulations demonstrated that modeling PLLA using the FEN constitutive relationship accurately reproduced the specimen’s force–displacement curve, and therefore, is a suitable relationship to use when simulating stress distribution in PLLA medical devices. This study demonstrates the utility of an advanced constitutive model that incorporates viscoplasticity for simulating PLLA mechanical behavior.

A Cyclic Stress-Strain Constitutive Model for Polycrystalline Magnesium Alloy and its Application

2007 ◽  
Vol 546-549 ◽  
pp. 81-88
Author(s):  
Xiang Guo Zeng ◽  
Qing Yuan Wang ◽  
Jing Hong Fan ◽  
Zhan Hua Gao ◽  
Xiang He Peng
Keyword(s):  
Magnesium Alloy ◽  
Constitutive Model ◽  
Cyclic Stress ◽  
Stress And Strain ◽  
Slip Systems ◽  
Stress Strain ◽  
Strain Behavior ◽  
Cast Magnesium ◽  
Magnesium Alloy Am60 ◽  
Good Agreement

The stress-strain behavior of cast magnesium alloy (AM60) was investigated by strain-controlled cyclic testing carried out on MTS. In order to describe the cyclic stress and strain properties of AM60 by means of the energy storing characteristics of microstructure during irreversible deformation, a plastic constitutive model with no yielding surface was developed for single crystal by adopting a spring-dashpot mechanical system. Plastic dashpots reflecting the material transient response were introduced to describe the plasticity of slip systems. By utilizing the KBW self-consistent theory, a polycrystalline plastic constitutive model for Magnesium alloy was formed. The numerical analysis in the corresponding algorithm is greatly simplified as no process of searching for the activation of the slip systems and slip directions is required. The cyclic stress-strain behavior, based on this model, is discussed. The simulation results show good agreement with the experimental data for AM60.

Sign in / Sign up

Export Citation Format

Share Document