scholarly journals Design and Optimization of LTE 1800 MIMO Antenna

2014 ◽  
Vol 2014 ◽  
pp. 1-10 ◽  
Author(s):  
Huey Shin Wong ◽  
Mohammad Tariqul Islam ◽  
Salehin Kibria
Keyword(s):  
Microstrip Antenna ◽  
Coplanar Waveguide ◽  
High Gain ◽  
Monopole Antenna ◽  
The Other ◽  
Mimo Antenna ◽  
Design And Optimization ◽  
Multiple Input ◽  
Wireless Application ◽  
Better Than

A multiple input and multiple output (MIMO) antenna that comprises a printed microstrip antenna and a printed double-L sleeve monopole antenna for LTE 1800 wireless application is presented. The printed double-L sleeve monopole antenna is fed by a 50 ohm coplanar waveguide (CPW). A novel T-shaped microstrip feedline printed on the other side of the PCB is used to excite the waveguide’s outer shell. Isolation characteristics better than −15 dB can be obtained for the proposed MIMO antenna. The proposed antenna can operate in LTE 1800 (1710 MHz–1880 MHz). This antenna exhibits omnidirectional characteristics. The efficiency of the antenna is greater than 70% and has high gain of 2.18 dBi.

Near Zero Parameter Metamaterial Inspired Superstrate for Isolation Improvement in MIMO Wireless Application

Frequenz ◽  
2020 ◽  
Vol 74 (1-2) ◽  
pp. 17-23
Author(s):  
Robert Mark ◽  
Soma Das
Keyword(s):  
Multiple Input Multiple Output ◽  
High Gain ◽  
Antenna System ◽  
Impedance Bandwidth ◽  
Mimo Antenna ◽  
Multiple Input ◽  
Input Multiple Output ◽  
Wireless Application ◽  
Measured Impedance ◽  
Edge Separation

AbstractIn this paper, near zero parameter based metamaterial superstrate is presented for mutual coupling reduction in multiple-input-multiple-output (MIMO) antenna. The proposed design offers a peak isolation of 38 dB with edge-separation of 0.042λ0 at resonating frequency. To verify the simulations results, a prototype of the proposed antenna is fabricated and experimentally measured. The two elements MIMO is designed with measured impedance bandwidth of 5.6 to 5.95 GHz with a peak measured gain of 7.4 dBi and efficiency above 95 %.The measurement established an isolation enhancement of 30 dB with minimum correlation coefficient of 0.05 within operating band. The proposed method offers a good design technique for high gain and closely packed MIMO antenna system for WLAN applications.

scholarly journals A High Isolation MIMO Antenna without Decoupling Structure for LTE 700 MHz

2015 ◽  
Vol 2015 ◽  
pp. 1-7 ◽  
Author(s):  
Yanjie Wu ◽  
Yunliang Long
Keyword(s):  
Impedance Matching ◽  
Multiple Input Multiple Output ◽  
Monopole Antenna ◽  
Antenna Element ◽  
Mimo Antenna ◽  
High Isolation ◽  
Antenna Performance ◽  
Measurement Results ◽  
Multiple Input ◽  
Input Multiple Output

This paper presents a long-term evolution (LTE) 700 MHz band multiple-input-multiple-output (MIMO) antenna, and high isolation between the two symmetrical antenna elements is obtained without introducing extra decoupling structure. Each antenna element is a combination antenna of PIFA and a meander monopole antenna. The end of the PIFA and the meander monopole antenna are, respectively, overlapped with the 50 Ω microstrip feed line, the two overlapping areas produce additional capacitance which can be considered decoupling structures to enhance the isolation for the MIMO antenna, as well as the impedance matching of the antenna elements. The MIMO antenna is etched on FR4 PCB board with dimensions of 71 × 40 × 1.6 mm3; the edge-to-edge separation of the two antenna elements is only nearly 0.037 λat 700 MHz. Both simulation and measurement results are used to confirm the MIMO antenna performance; the operating bandwidth is 698–750 MHz withS11≤−6 dB andS21≤−23 dB.

Compact UWB–MIMO antenna with quad-band-notched characteristic

2016 ◽  
Vol 9 (5) ◽  
pp. 1147-1153 ◽  
Author(s):  
Ling Wu ◽  
Yingqing Xia
Keyword(s):  
Correlation Coefficient ◽  
Radiation Pattern ◽  
Mimo System ◽  
Ground Plane ◽  
Multiple Input Multiple Output ◽  
Mimo Antenna ◽  
X Band ◽  
Multiple Input ◽  
Input Multiple Output ◽  
Better Than

With quad-band-notched characteristic, a compact ultrawideband (UWB) multiple-input-multiple-output (MIMO) antenna is introduced in the paper. The UWB–MIMO system has two similar monopole elements and occupies 30 × 45 mm2. By inserting two L-shaped slots, CSRR and C-shaped stubs, four notched bands are achieved (3.25–3.9, 5.11–5.35, 5.5–6.06, and 7.18–7.88 GHz) to filter WiMAX, lower WLAN, upper WLAN, and X-band. Meanwhile, the isolation is obviously enhanced with three metal strips on the ground plane. Results indicate that the antenna covers UWB frequency band of 3.1 – 10.6 GHz except four rejected bands, isolation of better than −18 dB, envelope correlation coefficient of <0.02, and good radiation pattern, thus making it useful for UWB systems.

scholarly journals Desain U-slot Ganda untuk Meningkatkan Bandwidth Antena MIMO 5G Millimeter-wave

2020 ◽  
Vol 8 (1) ◽  
pp. 150
Author(s):  
EFRI SANDI ◽  
WISNU DJATMIKO ◽  
RIZKITA KURNIA PUTRI
Keyword(s):  
Millimeter Wave ◽  
Microstrip Antenna ◽  
Multiple Input Multiple Output ◽  
Antenna Design ◽  
Frequency Allocation ◽  
Mimo Antenna ◽  
Main Requirement ◽  
Multiple Input ◽  
Input Multiple Output ◽  
High Bandwidth

ABSTRAK Pada penelitian ini dikembangkan rekayasa antena mikrostrip (MSA) dengan penambahan U-slot ganda untuk meningkatkan performansi bandwidth antena mikrostrip. Penelitian sebelumnya berfokus pada penambahan U-slot tunggal dan didesain untuk frekuensi di bawah 15 GHz. Kebutuhan utama antena 5G adalah memiliki bandwidth yang lebar dan kemampuan Multiple Input Multiple Output (MIMO). Untuk itu perlu dikembangkan desain antena MIMO 5G dengan bandwidth yang lebih lebar pada frekuensi millimeter-wave 28 GHz sebagai kandidat utama alokasi frekuensi untuk komunikasi seluler 5G. Pada penelitian ini diajukan teknik desain antena MIMO dengan penambahan rekayasa U-slot ganda untuk meningkatkan performansi bandwidth. Hasil kalkulasi dan simulasi menunjukkan bahwa dengan penambahan U-slot ganda, dihasilkan peningkatan performansi bandwith sebesar 68% dibandingkan desain antena tanpa U-slot. Jika dibandingkan dengan hasil penelitian U-slot sebelumnya, penambahan U-slot ganda menghasilkan peningkatan bandwidth sebesar 76%. Kata kunci: U-Slot ganda, antena 5G millimeter-wave, MIMO, bandwidth ABSTRACT In this study, a microstrip antenna (MSA) was developed with the addition of a double U-slot to improve bandwidth performance. Previous studies have focused on adding single U-slots and designed for frequencies below 15 GHz. The main requirement for 5G antennas is high bandwidth performance and multiple inputmultiple output capabilities (MIMO). Therefore, it is necessary to develop a 5G MIMO antenna with broader bandwidth at the millimeter-wave frequency 28 GHz as the primary candidate for frequency allocation for 5G cellular communication. In this study, MIMO antenna design techniques were proposed with the addition of a double U-slot method to improve bandwidth performance. The calculation and simulation results show that with the addition of a double U-slot, an increase in bandwidth performance of 68% compared to antenna designs without U-slots and 76% when compared to using a single U-slot in previous studies. Keywords: Double U-Slot, millimeter-wave 5G antenna, MIMO, bandwidth

scholarly journals Metamaterial-Based Highly Isolated MIMO Antenna for Portable Wireless Applications

Electronics ◽  
2018 ◽  
Vol 7 (10) ◽  
pp. 267 ◽  
Author(s):  
Amjad Iqbal ◽  
Omar A Saraereh ◽  
Amal Bouazizi ◽  
Abdul Basir
Keyword(s):  
Mutual Coupling ◽  
Multiple Input Multiple Output ◽  
High Gain ◽  
Metamaterial Structure ◽  
Mimo Antenna ◽  
Wireless Applications ◽  
Capacity Loss ◽  
Multiple Input ◽  
Input Multiple Output ◽  
Edge Separation

In this paper, a metamaterial structure is presented to lower the mutual coupling between the closely spaced microstrip patch antenna elements. Two elements Multiple Input Multiple Output (MIMO) antenna is closely placed with each other at edge to edge separation of 0.135 λ 0 (7 mm). Isolation improvement of 9 dB is achieved by keeping the metamaterial structure in between the MIMO elements. With the proposed structure, the isolation is achieved around −24.5 dB. Due to low ECC, high gain, low channel capacity loss and very low mutual coupling between elements, the proposed antenna is a good candidate for the MIMO applications. The proposed antenna is fabricated and tested. A reasonable agreement between simulated and measured results is observed.

scholarly journals Design of a Novel Triple Band Monopole Antenna for WLAN/WiMAX MIMO Applications in the Laptop Computer

2019 ◽  
Vol 2019 ◽  
pp. 1-11 ◽  
Author(s):  
Jayshri Kulkarni ◽  
Raju Seenivasan ◽  
V. Abhaikumar ◽  
Deepak Ram Prasath Subburaj
Keyword(s):  
Antenna Array ◽  
Correlation Coefficient ◽  
Monopole Antenna ◽  
Antenna Design ◽  
Impedance Bandwidth ◽  
Laptop Computer ◽  
Multiple Input ◽  
Medium Band ◽  
Better Than ◽  
Triple Band

This paper presents a triple band monopole antenna design with an overall size of 21  ×  8  mm2 for WLAN/WiMAX Multiple Input and Multiple Output (MIMO) applications in the laptop computer. It comprises of three monopole radiating elements, along with two rectangular open-ended tuning stubs. This structure excites 2.4/5.2/5.8 GHz WLAN and 2.3/3.3/5.5 GHz WiMAX bands. The prototype testing of proposed antenna array formed by using the same antenna design shows that, it has measured -10dB impedance bandwidth of 11.86% (2.22-2.50 GHz) in a lower band (fl), 5% (3.25-3.42 GHz) in medium band (fm) and 16.84% (5.00-5.92 GHz) in upper band (fu). The measured gain and radiation efficiency are well above 3.65 dBi and 75%, respectively, throughout the operating bands. Also, the measured isolation between two antennas is better than -20dB and envelope correlation coefficient (ECC) is less than 0.004 across the three bands of interest. This confirms the applicability of the proposed antenna array for MIMO applications in the laptop computer.

Design of a Miniaturized UWB-MIMO Antenna with Four Notched-Band Characteristics

Frequenz ◽  
2019 ◽  
Vol 73 (7-8) ◽  
pp. 245-252 ◽  
Author(s):  
Ling Wu ◽  
Hao Lyu ◽  
Huaqing Yu ◽  
Jing Xu
Keyword(s):  
Radiation Pattern ◽  
Multiple Input Multiple Output ◽  
Mimo Antenna ◽  
Ground Plan ◽  
Notched Band ◽  
X Band ◽  
Multiple Input ◽  
Input Multiple Output ◽  
Better Than

Abstract With four rejected bands, a miniaturized ultrawideband multiple-input-multiple-output (UWB-MIMO) antenna is presented. Four notched bands are realized by applying three pairs of L-shape slots and two symmetrical C-like metal stubs. Thus the system can relief latent interference from 3.5 GHz WiMAX/5.3 GHz lower WLAN/5.8 GHz upper WLAN/8.1 GHz X-band. To minimize port coupling and covering 3.1–10.6 GHz UWB band, a T-like metal stub is designed in the ground plan. The results proves that the antenna has four rejected bands across the working band of 3.1 ~ 11 GHz. Moreover, the antenna has compact volume of 21 × 27 × 0.8 mm3, better than −18 dB port isolation, preferable radiation pattern and gentle gain.

Dual circular slot ring triple-band MIMO antenna for 5G applications

Frequenz ◽  
2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Anand Kumar ◽  
Santosh Kumar Mahto ◽  
Rashmi Sinha ◽  
Arvind Choubey
Keyword(s):  
Mutual Coupling ◽  
Ground Plane ◽  
Multiple Input Multiple Output ◽  
Mobile Terminal ◽  
High Gain ◽  
Mimo Antenna ◽  
Multiple Input ◽  
Input Multiple Output ◽  
Smart Wearable ◽  
Triple Band

AbstractA Triple-band Multiple-Input-Multiple-Output (MIMO) antenna for 5G mobile terminal applications is proposed in this paper. The design comprises four-port/two resonators, each having two concentric circular slot ring radiators etched on a ground plane of size 50 mm ${\times}$ 50 mm. The antenna is fed by perpendicularly arranged 50 Ω microstrip line feeds on the top layer. Decoupling techniques were used to suppress mutual coupling between the two resonators. The perpendicular arrangement of the feed lines and port reduces mutual coupling between the two ports and increases isolation. The antenna operates in multiple bands: 3.35–3.69 GHz, 24–28 GHz, and 37–40 GHz frequency range with central frequencies at 3.5 GHz, 26 GHz, and 38 GHz, respectively allocated for 5G. The antenna provides a gain of 2.7–7.8 dB and a radiation efficiency of 0.49–0.85 in the operating bands. Diversity performance is studied in terms of the Envelop Correlation Coefficient (ECC), Diversity Gain (DG), and Total Active Reflection Coefficient (TARC) were found to be less than 0.01, greater than 9.99 dB, and less than −10 dB respectively. The proposed antenna offers good S-parameters, voltage standing wave ratio (VSWR), TARC, radiation pattern, high gain, and low ECC. The antenna was fabricated and tested. The measured results and simulated results are in good agreement. It possesses sufficient potential for 5G mobile terminal and smart wearable applications.

scholarly journals Bandwidth enhancement and miniaturization of circular-shaped microstrip antenna based on beleved half-cut structure for MIMO 2x2 application

2019 ◽  
Vol 9 (2) ◽  
pp. 1110 ◽  
Author(s):  
Teguh Firmansyah ◽  
Supriyanto Praptodiyono ◽  
Herudin Herudin ◽  
Didik Aribowo ◽  
Syah Alam ◽  
...  
Keyword(s):  
Microstrip Antenna ◽  
Mutual Coupling ◽  
Multiple Input Multiple Output ◽  
Center Frequency ◽  
Design System ◽  
Antenna Structure ◽  
Bandwidth Enhancement ◽  
Mimo Antenna ◽  
Multiple Input ◽  
Input Multiple Output

<span lang="EN-US">In this paper, circular-shaped microstrip antenna was simulated, fabricated, and measured accordingly. As the novelty, to enhance bandwidth and reduce antenna size, beleved half-cut microstrip structure is proposed. Further, this proposed antenna structure will be applied to multiple input multiple output (MIMO) antenna 2</span><span lang="EN-US">´</span><span lang="EN-US">2. Therefore, this research was investigated conventional circular shape antenna (CCSA), circular shaped beleved antenna (CSBA), and MIMO circular shaped beleved antenna (MIMO-CBSA) as Model 1, Model 2, and Model 3, respectively. An FR4 substrate with er= 4.4, thickness h=1.6 mm, and tan d=0.0265 was used. The simulation has been conducted using Advanced Design System (ADS). The antenna CCSA/CSBA/ MIMO-CBSA achieve 1.831GHz/2.265 GHz/2.256 GHz, -15.13dB/-17.37dB/-17.25 dB, 1.42/1.31/1.33, and 1.474/2.332/2.322 for center frequency, reflection coefficient, VSWR, and bandwidth, respectively. This antenna has a size 63x90 mm and 51.5x90 mm for CCSA (Model 1) and CSBA (Model 2), respectively. After the structure of MIMO 2</span><span lang="EN-US">´</span><span lang="EN-US">2 was applied, the size of antenna MIMO-CBSA (Model 3) became 180 mm x 180 mm with a mutual coupling (S<sub>21</sub>)=-26.18 dB and mutual coupling (S<sub>31</sub>)=-26.41 dB. The result showed that proposed antenna CSBA (Model 2) has wider-bandwidth of 58,2% and smaller-size of 18.2%. Furthermore, after CSBA (Model 2) structure was applied to MIMO 2</span><span lang="EN-US">´</span><span lang="EN-US">2 (Model 3) and the MIMO antenna obtain good mutual coupling (&lt;-15dB). Moreover, the measured results are good agreement with the simulated results. In conclusion, all of these advantages make it particularly valuable in multistandard antenna applications design such as GSM950, WCDMA1800, LTE2300, and WLAN2400.</span>

Compact 4-Port MIMO/Diversity Antenna with Low Correlation for UWB Application

Frequenz ◽  
2018 ◽  
Vol 72 (9-10) ◽  
pp. 429-435 ◽  
Author(s):  
Rohit Mathur ◽  
Santanu Dwari
Keyword(s):  
Group Delay ◽  
Multiple Input Multiple Output ◽  
Polarization Diversity ◽  
Mimo Antenna ◽  
S Parameter ◽  
Compact Size ◽  
Multiple Input ◽  
Input Multiple Output ◽  
Diversity Antenna ◽  
Better Than

Abstract A compact four port multiple-input-multiple-output (MIMO) antenna with polarization diversity for ultrawideband (UWB) application is proposed. The antenna contains four monopoles where each monopole has three concentric rings. Orthogonal arrangement of monopoles of the antenna provides good isolation and polarization diversity. The antenna has compact size of 36×36×1.6 mm3. It operates in the frequency band of 3.2 to 11 GHz where isolation is better than 15 dB. The envelop correlation coefficient (ECC) and diversity gain from S-parameter have been calculated to evaluate MIMO performance of the antenna. In addition to ensure distortion less transmission in UWB group delay is also calculated.

Sign in / Sign up

Export Citation Format

Share Document