scholarly journals Characterization of Modified Magnetite Nanoparticles for Albumin Immobilization

2014 ◽  
Vol 2014 ◽  
pp. 1-6 ◽  
Author(s):  
A. K. Bordbar ◽  
A. A. Rastegari ◽  
R. Amiri ◽  
E. Ranjbakhsh ◽  
M. Abbasi ◽  
...  
Keyword(s):  
Sol Gel ◽  
Xrd Analysis ◽  
Covalent Immobilization ◽  
Initial Value ◽  
X Ray ◽  
Buffer Solutions ◽  
Transmission Electron ◽  
Ft Ir ◽  
Chemical Coprecipitation Method

Magnetite Fe3O4 nanoparticles (NPs) were prepared by chemical coprecipitation method. Silica-coated magnetite NPs were prepared by sol-gel reaction, subsequently coated with 3-aminopropyltriethoxysilane (APTES) via silanization reaction, and then were activated with 2,4,6-trichloro-1,3,5-triazine (TCT) and covalently immobilized with bovine serum albumin (BSA). The size and structure of the particles were characterized by transmission electron microscopy (TEM), X-ray powder diffraction (XRD), and dynamic light scattering (DLS) techniques. The immobilization was confirmed by Fourier transform infrared spectroscopy (FT-IR). XRD analysis showed that the binding process has not done any phase change to Fe3O4. The immobilization time for this process was 4 h and the amount of immobilized BSA for the initial value of 1.05 mg BSA was about 120 mg/gr nanoparticles. Also, the influences of three different buffer solutions and ionic strength on covalent immobilization were evaluated.

Synthesis and Characterization of Bi2Al4O9 Powders

2012 ◽  
Vol 624 ◽  
pp. 34-37
Author(s):  
Xiao Yan Zhang ◽  
Wen Shu Hu ◽  
Xi Wei Qi ◽  
Gui Fang Sun ◽  
Jian Quan Qi ◽  
...  
Keyword(s):  
Crystallization Process ◽  
Sol Gel ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
Absorption Bands ◽  
X Ray ◽  
Oxide Powders ◽  
Sol Gel Process ◽  
Ft Ir

Bi2Al4O9 powders were prepared by sol-gel process. The precursors were heated at 500-800°C for 2h to obtain Bi2Al4O9 powder and X-ray diffraction (XRD), Differential thermal analysis (DTA), thermogravimetric analysis (TG), field emission scanning electron microscope (SEM), Fourier transform infrared spectroscopy (FT-IR) techniques were used to characterize precursor and derived oxide powders. XRD analysis show that the powder is still amorphous after calcined at 500°C. The peaks of Bi2Al4O9 become sharp after calcined at 575°C though still existing some amorphous phase. After calcining at 675-800°C, the powder has fully turned into pure Bi2Al4O9 phase. The crystallization process can also be confirmed by DTA-TG and IR. Calcining the precursor at 575°C, the absorption bands at 527 cm-1, 738 cm-1, 777 cm-1, and 919 cm-1are observed, which are assigned to Bi2Al4O9 and becoming stronger and sharper with the increase of temperature.

Characterization of ordered mesoporous films on silicon (001) surface using X-ray and electron diffraction

2005 ◽  
Vol 38 (1) ◽  
pp. 211-216 ◽  
Author(s):  
Pang-Hung Liu ◽  
Kuei-Jung Chao ◽  
Xing-Jian Guo ◽  
Kuo-Ying Huang ◽  
Yen-Ru Lee ◽  
...  
Keyword(s):  
Electron Diffraction ◽  
Sol Gel ◽  
Dip Coating ◽  
Silica Film ◽  
Continuous Film ◽  
X Ray ◽  
Transmission Electron ◽  
Ordered Mesoporous ◽  
Direction Dependence

A continuous silica film with well aligned mesochannels parallel to the Si(001) surface was found to be formed through sol–gel dip-coating of a silica precursor with nonionic ethylene oxide surfactant. Two two-dimensional mesoporous structures in centered and non-centered rectangular symmetries and with the short axes of elongated ellipsoidal pores normal to the surface were observed by X-ray and electron diffraction. Detailed transmission electron microscopy investigations were employed to view the direction dependence of the channel or pore packing in the continuous film.

One Step Synthesis and Characterization of Zirconia-Graphene Composites

2012 ◽  
Vol 600 ◽  
pp. 174-177 ◽  
Author(s):  
Jian Fei Xia ◽  
Zong Hua Wang ◽  
Yan Zhi Xia ◽  
Fei Fei Zhang ◽  
Fu Qiang Zhu ◽  
...  
Keyword(s):  
Synthesis And Characterization ◽  
Two Dimensional ◽  
X Ray Diffraction ◽  
X Ray ◽  
Graphene Composite ◽  
Transmission Electron ◽  
One Step ◽  
Ft Ir ◽  
Xrd Techniques

Zirconia-graphene composite (ZrO2-G) has been successfully synthesized via decomposition of ZrOCl2•6H2O in a water-isopropanol system with dispersed graphene oxide (GO) utilizing Na2S as a precursor could enable the occurrence of the deposition of Zr4+ and the deoxygenation of GO at the same time. Transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FT-IR) and X-ray diffraction (XRD) techniques were used to characterize the samples. It was found that graphene were fully coated with ZrO2, and the ZrO2 existing in tetragonal phase, which resulted in the formation of two-dimensional composite.

scholarly journals Hydrogenative Cyclization of Levulinic Acid to γ-Valerolactone with Methanol and Ni-Fe Bimetallic Catalysts

Catalysts ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1096
Author(s):  
Ligang Luo ◽  
Xiao Han ◽  
Qin Zeng
Keyword(s):  
Photoelectron Spectroscopy ◽  
Levulinic Acid ◽  
Hydrogen Donor ◽  
Effect Of Temperature ◽  
X Ray ◽  
Transmission Electron ◽  
Ft Ir ◽  
Temperature Programmed

A series of Ni-Fe/SBA-15 catalysts was prepared and tested for the catalytic hydrogenation of levulinic acid to γ-valerolactone, adopting methanol as the only hydrogen donor, and investigating the synergism between Fe and Ni, both supported on SBA-15, towards this reaction. The characterization of the synthesized catalysts was carried out by XRD (X-ray powder diffraction), TEM (transmission electron microscopy), H2-TPD (hydrogen temperature-programmed desorption), XPS (X-ray photoelectron spectroscopy), and in situ FT-IR (Fourier transform–infrared spectroscopy) techniques. H2-TPD and XPS results have shown that electron transfer occurs from Fe to Ni, which is helpful both for the activation of the C=O bond and for the dissociative activation of H2 molecules, also in agreement with the results of the in situ FT-IR spectroscopy. The effect of temperature and reaction time on γ-valerolactone production was also investigated, identifying the best reaction conditions at 200 °C and 180 min, allowing for the complete conversion of levulinic acid and the complete selectivity to γ-valerolactone. Moreover, methanol was identified as an efficient hydrogen donor, if used in combination with the Ni-Fe/SBA-15 catalyst. The obtained results are promising, especially if compared with those obtained with the traditional and more expensive molecular hydrogen and noble-based catalysts.

Sol-Gel Synthesis and Characterization of Nanocrystalline Bi4Ti3O12 Powders

2014 ◽  
Vol 997 ◽  
pp. 359-362 ◽  
Author(s):  
Chun Hong Ma ◽  
Xue Lin ◽  
Liang Wang ◽  
Yong Sheng Yan
Keyword(s):  
Phase Inversion ◽  
Bismuth Titanate ◽  
Sol Gel ◽  
Tetrabutyl Titanate ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Sol Gel Synthesis ◽  
Source Materials

Nanocrystalline bismuth titanate (Bi4Ti3O12; BTO) powders were successfully prepared by the sol-gel method, using bismuth nitrate (Bi(NO3)3·5H2O) and tetrabutyl titanate (Ti(OC4H9)4) as source materials, acetic anhydride and ethanediol as solvents. The thermal decomposition and phase inversion process of the gel precursors were studied by using differential thermal analysis (DTA). The crystal structures and microstructures of BTO powders were investigated by using x-ray diffraction (XRD), and transmission electron microscope (TEM). The crystallization of amorphous bismuth titanate has been discussed. The effect of sintering temperature on the structure and morphology of BTO was investigated. At 644 oC and above, BTO powder undergoes a phase transformation from tetragonal to orthorhombic. At 900 oC, the purified orthorhombic BTO nanocrystals were obtained.

Synthesis and Characterization of Organic/Inorganic Interpenetrating Polymer Networks

1995 ◽  
Vol 385 ◽  
Author(s):  
Barry J. Bauer ◽  
Catheryn L. Jackson ◽  
Da-Wei Liu
Keyword(s):  
Sol Gel ◽  
Polymer Networks ◽  
Interpenetrating Polymer Networks ◽  
X Ray ◽  
X Ray Scattering ◽  
Transmission Electron ◽  
Pure Phases ◽  
Hydrolysis Of ◽  
Polymerization Conditions

ABSTRACTInterpenetrating polymer networks have been synthesized by performing sol-gel chemistry and conventional organic polymerizations in mixtures of the monomers. The organic polymers were acrylates, and the inorganic phase was SiO2 formed by hydrolysis of orthosilicates. Polymerizations were conducted at a variety of relative rates, and the chemistry was designed to allow different amounts of grafting between the components. The morphology was characterized by transmission electron microscopy and small angle neutron and x-ray scattering. Wide variations in morphology were observed depending on the polymerization conditions, ranging from grossly phase separated to dendritic to finely divided structures (at a 100Å size scale). The phases ranged from mixtures of the two components to relatively pure phases. The interface between the phases ranged from very narrow to relatively broad.

Growth and Characterization of PZT Thin Films

2008 ◽  
Author(s):  
Daqun Bao ◽  
Yi Zhang ◽  
Hang Guo
Keyword(s):  
Thin Films ◽  
Sol Gel ◽  
Xrd Analysis ◽  
Annealing Process ◽  
Pzt Thin Films ◽  
X Ray ◽  
Crystallographic Structures ◽  
Strain Equation

This paper presents the growth and characterization of PZT thin films by using the sol-gel technology. In this paper, we study the influences of annealing process and different substrates on the orientation and crystalline quality of PZT thin films. The crystallographic structures are tested by using X-ray diffractometer (XRD), and the residual stresses of PZT thin films are obtained by calculation from a derived stress-strain equation in XRD analysis. Moreover, surface morphology and microstructure of the films are investigated by using AFM and SEM, and the polarization hysteresis of PZT thin films is measured by using a Sawyer Tower circuit. The results show that PZT thin films prepared by using the sol-gel method have good properties and can be used for developing PZT-based micro and nano devices.

Synthesis and Characterization of HgSe Nanostructure Using a Novel Precursor

2013 ◽  
Vol 32 (2) ◽  
pp. 157-162 ◽  
Author(s):  
Mahdiyeh Esmaeili-Zare ◽  
Masoud Salavati-Niasari ◽  
Davood Ghanbari
Keyword(s):  
Electron Microscopy ◽  
Synthesis And Characterization ◽  
Sonochemical Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Mercury Selenide ◽  
Ft Ir ◽  
Ft Ir Spectroscopy

AbstractMercury selenide nanostructures were synthesized from the reaction of N, N′-bis(salicylidene)propane-1,3-diamine mercury complex, (Hg(Salpn)) as a novel precursor, via sonochemical method. The effect of different surfactant on the morphology and particle size of the products was investigated. Products were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared (FT-IR) spectroscopy and X-ray energy dispersive spectroscopy (EDS).

Sol-gel derived Ba(Mg1/3Ta2/3)O3 thin films: Preparation and structure

1997 ◽  
Vol 12 (3) ◽  
pp. 596-599 ◽  
Author(s):  
Ji Zhou ◽  
Qing-Xin Su ◽  
K. M. Moulding ◽  
D. J. Barber
Keyword(s):  
Thin Films ◽  
Annealing Temperature ◽  
Volume Fraction ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Sol Gel Process ◽  
Small Grains

Ba(Mg1/3Ta2/3)O3 thin films were prepared by a sol-gel process involving the reaction of barium isopropoxide, tantalum ethoxide, and magnesium acetate in 2-methoxyethanol and subsequently hydrolysis, spin-coating, and heat treatment. Transmission electron microscopy, x-ray diffraction, and Raman spectroscopy were used for the characterization of the thin films. It was shown that the thin films tend to crystallize with small grains sized below 100 nm. Crystalline phase with cubic (disordered) perovskite structure was formed in the samples annealed at a very low temperature (below 500 °C), and well-crystallized thin films were obtained at 700 °C. Although disordered perovskite is dominant in the thin films annealed below 1000 °C, a low volume fraction of 1 : 2 ordering domains was found in the samples and grows with an increase of annealing temperature.

scholarly journals Isolation and Characterization of Cellulose Nanofibers fromGigantochloa scortechiniias a Reinforcement Material

2016 ◽  
Vol 2016 ◽  
pp. 1-8 ◽  
Author(s):  
Chaturbhuj K. Saurabh ◽  
Asniza Mustapha ◽  
M. Mohd. Masri ◽  
A. F. Owolabi ◽  
M. I. Syakir ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Cellulose Nanofibers ◽  
X Ray Diffraction ◽  
X Ray ◽  
Isolation And Characterization ◽  
Transmission Electron ◽  
Reinforcement Material ◽  
Bamboo Fibers ◽  
Ft Ir

Cellulose nanofibers (CNF) were isolated fromGigantochloa scortechiniibamboo fibers using sulphuric acid hydrolysis. This method was compared with pulping and bleaching process for bamboo fiber. Scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, X-ray diffraction, and thermogravimetric analysis were used to determine the properties of CNF. Structural analysis by FT-IR showed that lignin and hemicelluloses were effectively removed from pulp, bleached fibers, and CNF. It was found that CNF exhibited uniform and smooth morphological structures, with fiber diameter ranges from 5 to 10 nm. The percentage of crystallinity was significantly increased from raw fibers to cellulose nanofibers, microfibrillated, along with significant improvement in thermal stability. Further, obtained CNF were used as reinforcement material in epoxy based nanocomposites where tensile strength, flexural strength, and modulus of nanocomposites improved with the addition of CNF loading concentration ranges from 0 to 0.7%.

Sign in / Sign up

Export Citation Format

Share Document