scholarly journals Preparation, Characterization, and Enhanced Thermal and Mechanical Properties of Epoxy-Titania Composites

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
Zakya Rubab ◽  
Adeel Afzal ◽  
Humaira M. Siddiqi ◽  
Shaukat Saeed
Keyword(s):  
Mechanical Properties ◽  
Elevated Temperatures ◽  
Sol Gel ◽  
High Stress ◽  
Thermal And Mechanical Properties ◽  
Mechanical Mixing ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Thermal Oxidative Stability ◽  
Epoxy Polymers

This paper presents the synthesis and thermal and mechanical properties of epoxy-titania composites. First, submicron titania particles are prepared via surfactant-free sol-gel method using TiCl4as precursor. These particles are subsequently used as inorganic fillers (or reinforcement) for thermally cured epoxy polymers. Epoxy-titania composites are prepared via mechanical mixing of titania particles with liquid epoxy resin and subsequently curing the mixture with an aliphatic diamine. The amount of titania particles integrated into epoxy matrix is varied between 2.5 and 10.0 wt.% to investigate the effect of sub-micron titania particles on thermal and mechanical properties of epoxy-titania composites. These composites are characterized by X-ray photoelectron (XPS) spectroscopy, scanning electron microscopy (SEM), differential scanning calorimetry (DSC), thermogravimetric (TG), and mechanical analyses. It is found that sub-micron titania particles significantly enhance the glass transition temperature (>6.7%), thermal oxidative stability (>12.0%), tensile strength (>21.8%), and Young’s modulus (>16.8%) of epoxy polymers. Epoxy-titania composites with 5.0 wt.% sub-micron titania particles perform best at elevated temperatures as well as under high stress.

Electron microscopy of crystalline structure in thermotropic random copolymers

1991 ◽  
Vol 49 ◽  
pp. 1054-1055
Author(s):  
Afzana Anwer ◽  
S. Eilidh Bedford ◽  
Richard J. Spontak ◽  
Alan H. Windle
Keyword(s):  
Electron Microscopy ◽  
Crystalline Structure ◽  
Liquid Crystalline ◽  
Elevated Temperatures ◽  
Random Copolymers ◽  
Molecular Characteristics ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Identical Monomer ◽  
Periodic Layer

Random copolyesters composed of wholly aromatic monomers such as p-oxybenzoate (B) and 2,6-oxynaphthoate (N) are known to exhibit liquid crystalline characteristics at elevated temperatures and over a broad composition range. Previous studies employing techniques such as X-ray diffractometry (XRD) and differential scanning calorimetry (DSC) have conclusively proven that these thermotropic copolymers can possess a significant crystalline fraction, depending on molecular characteristics and processing history, despite the fact that the copolymer chains possess random intramolecular sequencing. Consequently, the nature of the crystalline structure that develops when these materials are processed in their mesophases and subsequently annealed has recently received considerable attention. A model that has been consistent with all experimental observations involves the Non-Periodic Layer (NPL) crystallite, which occurs when identical monomer sequences enter into register between adjacent chains. The objective of this work is to employ electron microscopy to identify and characterize these crystallites.

scholarly journals Effects of Sintering Temperature on Densification, Microstructure and Mechanical Properties of Al-Based Alloy by High-Velocity Compaction

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 218
Author(s):  
Xianjie Yuan ◽  
Xuanhui Qu ◽  
Haiqing Yin ◽  
Zaiqiang Feng ◽  
Mingqi Tang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Velocity ◽  
Sintered Density ◽  
Sintering Temperature ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron ◽  
High Velocity Compaction ◽  
Sintered Temperature

This present work investigates the effects of sintering temperature on densification, mechanical properties and microstructure of Al-based alloy pressed by high-velocity compaction. The green samples were heated under the flow of high pure (99.99 wt%) N2. The heating rate was 4 °C/min before 315 °C. For reducing the residual stress, the samples were isothermally held for one h. Then, the specimens were respectively heated at the rate of 10 °C/min to the temperature between 540 °C and 700 °C, held for one h, and then furnace-cooled to the room temperature. Results indicate that when the sintered temperature was 640 °C, both the sintered density and mechanical properties was optimum. Differential Scanning Calorimetry, X-ray diffraction of sintered samples, Scanning Electron Microscopy, Energy Dispersive Spectroscopy, and Transmission Electron Microscope were used to analyse the microstructure and phases.

Research on compatibility and surface of high impact bio-based polyamide

2021 ◽  
pp. 095400832110055
Author(s):  
Yang Wang ◽  
Yuhui Zhang ◽  
Yuhan Xu ◽  
Xiucai Liu ◽  
Weihong Guo
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Differential Scanning Calorimetry ◽  
Crystallization Behavior ◽  
High Impact ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Scanning Electron

The super-tough bio-based nylon was prepared by melt extrusion. In order to improve the compatibility between bio-based nylon and elastomer, the elastomer POE was grafted with maleic anhydride. Scanning Electron Microscopy (SEM) and Thermogravimetric Analysis (TGA) were used to study the compatibility and micro-distribution between super-tough bio-based nylon and toughened elastomers. The results of mechanical strength experiments show that the 20% content of POE-g-MAH has the best toughening effect. After toughening, the toughness of the super-tough nylon was significantly improved. The notched impact strength was 88 kJ/m2 increasing by 1700%, which was in line with the industrial super-tough nylon. X-ray Diffraction (XRD) and Differential Scanning Calorimetry (DSC) were used to study the crystallization behavior of bio-based PA56, and the effect of bio-based PA56 with high crystallinity on mechanical properties was analyzed from the microstructure.

Enhancing the Thermal and Mechanical Characteristics of Polyvinyl Alcohol (PVA)-Hemp Protein Particles (HPP) Composites

2021 ◽  
Vol 36 (2) ◽  
pp. 137-143
Author(s):  
S. A. Awad
Keyword(s):  
Mechanical Properties ◽  
Elevated Temperatures ◽  
Composite Films ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Decomposition Temperature ◽  
Scanning Calorimetry ◽  
Solution Casting Method ◽  
Protein Particles

Abstract This paper aims to describe the thermal, mechanical, and surface properties of a PVA/HPP blend whereby the film was prepared using a solution casting method. The improvements in thermal and mechanical properties of HPP-based PVA composites were investigated. The characterization of pure PVA and PVA composite films included tensile tests, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The results of TGA and DSC indicated that the addition of HPP increased the thermal decomposition temperature of the composites. Mechanical properties are significantly improved in PVA/HPP composites. The thermal stability of the PVA composite increased with the increase of HPP filler content. The tensile strength increased from 15.74 ± 0.72 MPa to 27.54 ± 0.45 MPa and the Young’s modulus increased from 282.51 ± 20.56 MPa to 988.69 ± 42.64 MPa for the 12 wt% HPP doped sample. Dynamic mechanical analysis (DMA) revealed that at elevated temperatures, enhanced mechanical properties because of the presence of HPP was even more noticeable. Morphological observations displayed no signs of agglomeration of HPP fillers even in composites with high HPP loading.

The Structure and Mechanical Properties of Plastically Consolidated Al-Ni Alloy

2016 ◽  
Vol 682 ◽  
pp. 245-251 ◽  
Author(s):  
Grzegorz Włoch ◽  
Tomasz Skrzekut ◽  
Jakub Sobota ◽  
Antoni Woźnicki ◽  
Justyna Cisoń
Keyword(s):  
Mechanical Properties ◽  
Vickers Hardness ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Intermetallic Phases ◽  
Scanning Calorimetry ◽  
Porosity Formation ◽  
X Ray ◽  
Ni Alloy ◽  
Thermal Stability Of

Mixed and preliminarily consolidated powders of aluminium and nickel (90 mass % Al and 10 mass % Ni) were hot extruded. As results the rod, 8 mm in diameter, was obtained. As-extruded material was subjected to the microstructural investigations using scanning electron microscopy (SEM/EDS) and X-ray analysis (XRD). The differential scanning calorimetry (DSC) and thermo-mechanical analysis (TMA) were also performed. The mechanical properties of as extruded material were determined by the tensile test and Vickers hardness measurements. In order to evaluate the thermal stability of PM alloy, samples were annealed at the temperature of 475 and 550 °C. After annealing Vickers hardness measurements and tensile tests were carried out. The plastic consolidation of powders during extrusion was found to be very effective, because no pores or voids were observed in the examined material. The detailed microstructural investigations and XRD analyses did not reveal the presence of the intermetallic phases in the as-extruded material. During annealing, the Al3Ni intermetallic compound was formed as the result of chemical reaction between the alloy components. The hardness of the alloy after annealing at the temperature of 475°C was found to be comparable to the hardness in as-extruded state. Annealing of the material at the temperature of 550°C results in hardness decreasing by about 50%, as the consequence of porosity formation and Al3Ni cracking.

Effects of Cooling Rate and Sn Addition on the Microstructure of Ti-Nb-Sn Alloys

2011 ◽  
Vol 172-174 ◽  
pp. 190-195 ◽  
Author(s):  
Giorgia T. Aleixo ◽  
Eder S.N. Lopes ◽  
Rodrigo Contieri ◽  
Alessandra Cremasco ◽  
Conrado Ramos Moreira Afonso ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Cooling Rate ◽  
Melting Furnace ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Β Phase ◽  
Arc Melting ◽  
Ti Alloys ◽  
Ω Phase

Ti-based alloys present unique properties and hence, are employed in several industrial segments. Among Ti alloys, β type alloys form one of the most versatile classes of materials in relation to processing, microstructure and mechanical properties. It is well known that heat treatment of Ti alloys plays an important role in determining their microstructure and mechanical behavior. The aim of this work is to analyze microstructure and phases formed during cooling of β Ti-Nb-Sn alloy through different cooling rates. Initially, samples of Ti-Nb-Sn system were prepared through arc melting furnace. After, they were subjected to continuous cooling experiments to evaluate conditions for obtaining metastable phases. Microstructure analysis, differential scanning calorimetry and X-ray diffraction were performed in order to evaluate phase transformations. Depending on the cooling rate and composition, α” martensite, ω phase and β phase were obtained. Elastic modulus has been found to decrease as the amount of Sn was increased.

Effects of walnut shell powders on the morphology and the thermal and mechanical properties of poly(lactic acid)

2019 ◽  
Vol 33 (10) ◽  
pp. 1383-1395
Author(s):  
Hongjuan Zheng ◽  
Zhengqian Sun ◽  
Hongjuan Zhang
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Property Testing ◽  
Walnut Shell ◽  
Poly Lactic Acid ◽  
Thermal And Mechanical Properties ◽  
Scanning Calorimetry ◽  
Elongation At Break ◽  
Heat Distortion Temperature ◽  
Testing Techniques

Poly(lactic acid) (PLA) has good environmental compatibility, however, its high brittleness, slow rate of crystallization, and low heat distortion temperature restrict its widespread use. To overcome these limitations, in this study, PLA was mixed with walnut shell (WS) powders. The effects of WS powders on the morphology and the thermal and mechanical properties of PLA were investigated. The products were characterized by differential scanning calorimetry (DSC), infrared (IR) spectroscopy, polarizing optical microscopy (POM), and various mechanical property testing techniques. The results showed that WS powders had a significant effect on the morphology and the thermal and mechanical properties of PLA. The tensile strength, impact strength, and elongation at break of the PLA/WS composites first increased and then decreased with the increasing addition of WS powders. When the addition of WS powders was about 0.5 wt%, they reached maximum values of 51.2 MPa, 23.3 MPa, and 19.0%, respectively. Compared with neat PLA, the spherulite grain size of the composites could be reduced and many irregular polygons were formed during crystallization. The melting, cold crystallization, and glass-transition temperatures of the composites were lower than those of neat PLA.

Structure and properties of poly(3-hydroxybutyrate-co-3-hydroxyhexanoate)/poly(L-lactic acid) quasi core/sheath melt-electrospun microfibers

2018 ◽  
Vol 89 (9) ◽  
pp. 1770-1781 ◽  
Author(s):  
Huaizhong Xu ◽  
Benedict Bauer ◽  
Masaki Yamamoto ◽  
Hideki Yamane
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Lactic Acid ◽  
Tensile Tests ◽  
Processing Parameters ◽  
Structure And Properties ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Diffraction Patterns

A facile route was proposed to fabricate core–sheath microfibers, and the relationships among processing parameters, crystalline structures and the mechanical properties were investigated. The compression molded poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBH)/poly(L-lactic acid) (PLLA) strip enhanced the spinnability of PHBH and the mechanical properties of PLLA as well. The core–sheath ratio of the fibers was determined by the prefab strip, while the PLLA sheath component did not completely cover the PHBH core component due to the weak interfacial tension between the melts of PHBH and PLLA. A rotational target was applied to collect aligned fibers, which were further drawn in a water bath. The tensile strength and the modulus of as-spun and drawn fibers increased with increasing the take-up velocities. When the take-up velocity was above 500 m/min, the jet became unstable and started to break up at the tip of the Taylor cone, decreasing the mechanical properties of the fibers. The drawing process facilitated the crystallization of PLLA and PHBH, and the tensile strength and the modulus increased linearly with the increasing the draw ratio. The crystal information displayed from wide-angle X-ray diffraction patterns and differential scanning calorimetry heating curves supported the results of the tensile tests.

Weldability of pipe grade polyethylenes as realized from thermal and mechanical properties assessments

2016 ◽  
Vol 36 (8) ◽  
pp. 853-860 ◽  
Author(s):  
Vahabodin Goodarzi ◽  
Zahed Ahmadi ◽  
Mohammad Reza Saeb ◽  
Farkhondeh Hemmati ◽  
Mehdi Ghaffari ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Analysis ◽  
Molecular Weight ◽  
Aging Process ◽  
Pipe Production ◽  
Lamellar Thickness ◽  
Thermal And Mechanical Properties ◽  
Scanning Calorimetry ◽  
Injection Molded ◽  
The One

Abstract Since polyethylene (PE) has been widely accepted for the production of high-pressure fluid conveying pipelines, studies devoted to weldability of PE connections were always of major importance. In this study, two industrial PE grades designed for pipe production, namely PE80 and PE100, were injection molded, cut, and then welded as PE100-PE100, PE100-PE80, and PE80-PE80. The heat-welded joints were assessed by differential scanning calorimetry and tensile measurements. The results obtained from thermal and mechanical analyses were compared with equivalents for aged samples. Thermal analysis revealed that the melting point of the PE100-PE100 sample is obviously larger than the one for the PE80-PE80 joint, for the PE80 chains deteriorate the crystallization of PE100. Further, the PE80-PE80 sample showed the lowest lamellar thickness and crystalline molecular weight among the studied joints. The aging process was found to increase lamellar thickness and molecular weight, though in the PE100-PE100 sample such quantities very limitedly increased. The yield stress of aged joints was higher than that for just-prepared samples, while an inverse trend was seen for strain at break. From a practical viewpoint, the PE100-PE100 welds offer better properties.

Sign in / Sign up

Export Citation Format

Share Document