scholarly journals Inviscid Uniform Shear Flow past a Smooth Concave Body

2014 ◽  
Vol 2014 ◽  
pp. 1-7
Author(s):  
Abdullah Murad
Keyword(s):  
Shear Flow ◽  
Stream Function ◽  
Inviscid Fluid ◽  
Oncoming Flow ◽  
Circular Arc ◽  
River Islands ◽  
Uniform Shear ◽  
Uniform Shear Flow ◽  
Flow Past ◽  
Special Cases

Uniform shear flow of an incompressible inviscid fluid past a two-dimensional smooth concave body is studied; a stream function for resulting flow is obtained. Results for the same flow past a circular cylinder or a circular arc or a kidney-shaped body are presented as special cases of the main result. Also, a stream function for resulting flow around the same body is presented for an oncoming flow which is the combination of a uniform stream and a uniform shear flow. Possible fields of applications of this study include water flows past river islands, the shapes of which deviate from circular or elliptical shape and have a concave region, or past circular arc-shaped river islands and air flows past concave or circular arc-shaped obstacles near the ground.

A perturbation analysis of the laminar far wake behind a symmetrical two-dimensional body in a uniform shear flow

1973 ◽  
Vol 61 (2) ◽  
pp. 305-321 ◽  
Author(s):  
Masaru Kiya ◽  
Mikio Arie
Keyword(s):  
Shear Flow ◽  
Stream Function ◽  
Perturbation Analysis ◽  
Maximum Velocity ◽  
Two Dimensional ◽  
Low Velocity ◽  
Velocity Defect ◽  
Uniform Shear ◽  
Uniform Shear Flow ◽  
Far Wake

An aspect of the laminar far wake behind a symmetrical two-dimensional body placed in a uniform shear flow is described theoretically by means of the Oseen type of successive approximation, in which the shear is regarded as a small perturbation on a uniform stream. The expression for the stream function is determined up to the third approximation both in and outside the wake region, and the region in which the results of the perturbation analysis are valid is also determined. The stream function is found to contain four constants which cannot be determined from the boundary conditions for the far wake. The analysis also shows that the spreading of the wake is greater towards the side of smaller velocity than the side of larger velocity, the asymmetrical feature of the velocity defect becoming more evident as the distance from the obstacle is increased: the point which shows the maximum velocity defect shifts to the low-velocity side.

Uniform shear flow past a circular cylinder

2005 ◽  
Vol 178 (3-4) ◽  
pp. 199-222 ◽  
Author(s):  
K. Rohlf ◽  
S. J. D. D’Alessio
Keyword(s):  
Circular Cylinder ◽  
Shear Flow ◽  
Uniform Shear ◽  
Uniform Shear Flow ◽  
Flow Past

Formation of Vortex Street in Laminar Boundary Layer

1980 ◽  
Vol 47 (2) ◽  
pp. 227-233 ◽  
Author(s):  
M. Kiya ◽  
M. Arie
Keyword(s):  
Boundary Layer ◽  
Shear Flow ◽  
Laminar Boundary Layer ◽  
Solid Wall ◽  
Vortex Sheet ◽  
Vortex Street ◽  
Bluff Bodies ◽  
Uniform Shear ◽  
Uniform Shear Flow ◽  
Vortex Patterns

Main features of the formation of vortex street from free shear layers emanating from two-dimensional bluff bodies placed in uniform shear flow which is a model of a laminar boundary layer along a solid wall. This problem is concerned with the mechanism governing transition induced by small bluff bodies suspended in a laminar boundary layer. Calculations show that the background vorticity of shear flow promotes the rolling up of the vortex sheet of the same sign whereas it decelerates that of the vortex sheet of the opposite sign. The steady configuration of the conventional Karman vortex street is not possible in shear flow. Theoretical vortex patterns are experimentally examined by a flow-visualization technique.

The formation mechanism and shedding frequency of vortices from a sphere in uniform shear flow

1995 ◽  
Vol 287 ◽  
pp. 151-171 ◽  
Author(s):  
Hiroshi Sakamoto ◽  
Hiroyuki Haniu
Keyword(s):  
Reynolds Number ◽  
Shear Flow ◽  
Formation Mechanism ◽  
Vortex Shedding ◽  
Uniform Flow ◽  
Sphere Diameter ◽  
Uniform Shear ◽  
Uniform Shear Flow ◽  
Vortex Loops ◽  
Shear Parameter

Experiments to investigate the formation mechanism and frequency of vortex shedding from a sphere in uniform shear flow were conducted in a water channel using flow visualization and velocity measurement. The Reynolds number, defined in terms of the sphere diameter and approach velocity at its centre, ranged from 200 to 3000. The shear parameter K, defined as the transverse velocity gradient of the shear flow non-dimensionalized by the above two parameters, was varied from 0 to 0.25. The critical Reynolds number beyond which vortex shedding from the sphere occurred was found to be lower than that for uniform flow and decreased approximately linearly with increasing shear parameter. Also, the Strouhal number of the hairpin-shaped vortex loops became larger than that for uniform flow and increased as the shear parameter increased.The formation mechanism and the structure of vortex shedding were examined on the basis of series of photographs and subsequent image processing using computer graphics. The range of Reynolds number in the present investigation, extending up to 3000, could be classified into three regions on the basis of this study, and it was observed that the wake configuration did not differ substantially from that for uniform flow. Also, unlike the detachment point of vortex loops in uniform flow, which was irregularly located along the circumference of the sphere, the detachment point in shear flow was always on the high-velocity side.

The heat/mass transfer to a finite strip at small Péclet numbers

1978 ◽  
Vol 86 (1) ◽  
pp. 49-65 ◽  
Author(s):  
R. C. Ackerberg ◽  
R. D. Patel ◽  
S. K. Gupta
Keyword(s):  
Heat Transfer ◽  
Mass Transfer ◽  
Shear Flow ◽  
Sodium Hydroxide Solution ◽  
Flow Direction ◽  
Mathematical Problem ◽  
Limiting Current ◽  
Transfer Rates ◽  
Uniform Shear ◽  
Uniform Shear Flow

The problem of heat transfer (or mass transfer at low transfer rates) to a strip of finite length in a uniform shear flow is considered. For small values of the Péclet number (based on wall shear rate and strip length), diffusion in the flow direction cannot be neglected as in the classical Leveque solution. The mathematical problem is solved by the method of matched asymptotic expansions and expressions for the local and overall dimensionless heat-transfer rate from the strip are found. Experimental data on wall mass-transfer rates in a tube at small Péclet numbers have been obtained by the well-known limiting-current method using potassium ferrocyanide and potassium ferricyanide in sodium hydroxide solution. The Schmidt number is large, so that a uniform shear flow can be assumed near the wall. Experimental results are compared with our theoretical predictions and the work of others, and the agreement is found to be excellent.

Sign in / Sign up

Export Citation Format

Share Document