scholarly journals An Experimental Study on Strength and Durability for Utilization of Fly Ash in Concrete Mix

2014 ◽  
Vol 2014 ◽  
pp. 1-6 ◽  
Author(s):  
Abdulhalim Karaşin ◽  
Murat Doğruyol
Keyword(s):  
Experimental Study ◽  
Compressive Strength ◽  
Fly Ash ◽  
Underground Water ◽  
Hardened Concrete ◽  
Concrete Deterioration ◽  
High Sulfate ◽  
Strength And Durability ◽  
Mineral Additives

The intention of this study is to discuss the variation of concrete exposed to high sulfate environment of a specific region with respect to strength and durability. Secondly, it is aimed to discuss the possibility of reducing the cement amount in construction of concrete structures. For this purpose, laboratory tests were conducted to investigate compressive strength and sulfate resisting capacity of concrete by using 20% fly ash as mineral additives, waste materials, instead of cement. As a case study the soil samples, received from Siirt Province areas which contain high sulfate rate, have been compared with respect to sulfate standard parameters of TS 12457-4. In such regions contact of underground water seep into hardened concrete substructures poses a risk of concrete deterioration. In order to determine the variation of strength and durability for concrete exposed to such aggressive environment, the samples were rested in a solution of Na2SO4(150 g/lt) in accordance with ASTM C 1012 for the tests. As a result of this experimental study, it is noted that the use of 20% fly ash, replacement material instead of cement, has no significant effect on compressive strength of concrete over time.

Microstructure and Mechanical Properties of Ambiently-Cured Blended Coal Ash-Based Geopolymer Concrete

2016 ◽  
Vol 857 ◽  
pp. 400-404
Author(s):  
Tian Yu Xie ◽  
Togay Ozbakkaloglu
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Compressive Strength ◽  
Fly Ash ◽  
Bottom Ash ◽  
Coal Ash ◽  
Geopolymer Concrete ◽  
Mass Ratio ◽  
Blended Coal ◽  
Microstructure And Mechanical Properties

This paper presents the results of an experimental study on the behavior of fly ash-, bottom ash-, and blended fly and bottom ash-based geopolymer concrete (GPC) cured at ambient temperature. Four bathes of GPC were manufactured to investigate the influence of the fly ash-to-bottom ash mass ratio on the microstructure, compressive strength and elastic modulus of GPC. All the results indicate that the mass ratio of fly ash-to-bottom ash significantly affects the microstructure and mechanical properties of GPCs

Experimental Study on Alkali-Activated Slag-Lithium Slag-Fly Ash Environmental Concrete

2011 ◽  
Vol 287-290 ◽  
pp. 1237-1240
Author(s):  
Lan Fang Zhang ◽  
Rui Yan Wang
Keyword(s):  
Experimental Study ◽  
Compressive Strength ◽  
Fly Ash ◽  
Setting Time ◽  
Alkali Activated Slag ◽  
Percent Increase ◽  
Compressive Strength Of Concrete ◽  
Activated Slag ◽  
Lithium Slag ◽  
Alkali Activated

The aim of this paper is to study the influence of lithium-slag and fly ash on the workability , setting time and compressive strength of alkali-activated slag concrete. The results indicate that lithium-slag and fly-ash can ameliorate the workability, setting time and improve the compressive strength of alkali-activated slag concrete，and when 40% or 60% slag was replaced by lithium-slag or fly-ash, above 10 percent increase in 28-day compressive strength of concrete were obtained.

scholarly journals The Effect of Fly Ash Microspheres on the Pore Structure of Concrete

Minerals ◽  
2020 ◽  
Vol 10 (1) ◽  
pp. 58 ◽  
Author(s):  
Elzbieta Haustein ◽  
Aleksandra Kuryłowicz-Cudowska
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Total Content ◽  
Spherical Particles ◽  
Hardened Concrete ◽  
Image Analysis System ◽  
Micro Computed Tomography ◽  
Concrete Technology ◽  
Air Voids ◽  
X Ray

The fly ash microspheres (FAMs) formed during the mineral transformation stage in coal combustion are hollow spherical particles with a density less than water. This paper presents the results of X-ray micro-computed tomography and an automatic image analysis system of the porosity in the structure of hardened concrete with microspheres. Concrete mixtures with ordinary Portland cement and two substitution rates of cement by microspheres—5% and 10%—are investigated. For all considered mixes, a constant water/binder ratio (w/b) equal to 0.50 was used. The distribution of the air voids and the compressive strength of the concrete were tested after 28 days. With the increasing mass of cement replacement by FAMs, the compressive strength decreases after 28 days. The total volume of the air voids in hardened concrete with fly ash microspheres tested by X-ray varies from 5.1% to 7.4%. The closed pores constitute more than 80% of the total content of air pores. The study proves that the use of microspheres grains with specific dimensions has a significant impact on concrete porosity. Their application in concrete technology can be an alternative aeration solution for fresh concrete mixes and an effective method for utilization.

scholarly journals Experimental study on the properties of highperformance concrete made with class C fly ash

2019 ◽  
Vol 276 ◽  
pp. 01014
Author(s):  
I Made Alit Karyawan Salain ◽  
I Nyoman Sutarja ◽  
Teguh Arifmawan Sudhiarta
Keyword(s):  
Experimental Study ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Permeability Coefficient ◽  
Splitting Tensile Strength ◽  
Type I ◽  
Fine Aggregate ◽  
Hydration Time ◽  
Class C

This experimental study presents the properties of highperformance concrete (HPC) made by partially replacing type I Portland cement (OPC) with class C fly ash (CFA). The purpose of this study is to examine, with hydration time, the development of the compressive strength, the splitting tensile strength and the permeability of HPC utilizing different quantity of CFA. Four HPC mixtures, C1, C2, C3, and C4, were made by utilizing respectively 10%, 20%, 30% and 40% of CFA as replacement of OPC, by weight. One control mixture, C0, was made with 0% CFA. The mix proportion of HPC was 1.00 binder: 1.67 fine aggregate: 2.15 coarse aggregate with water to binder ratio 0.32. In each mixture, it was added 5% silica fume and 0.6% superplasticizer of the weight of the binder. Tests of HPC properties were realized at the age of 1, 3, 7, 28, and 90 days. The results indicate that CFA used to partially replace OPC in HPC shows adequate cementitious and pozzolanic properties. The compressive strength and the splitting tensile strength of HPC increase while the permeability coefficient decreases with increasing hydration time. It is found that the optimum replacement of OPC with CFA is 10%, however the replacement up to 20% is still acceptable to produce HPC having practically similar harden properties with control mixture. At this optimum replacement and after 90 days of hydration, the compressive strength, the splitting tensile strength and the permeability coefficient can reach 68.9 MPa, 8.3 MPa and 4.6 E-11 cm/sec respectively. These results are 109%, 101%, and 48% respectively of those of control mixture.

Investigation on Thermal Stability of Geopolymer Based Zeolite in Fire Case Study

2020 ◽  
Vol 1009 ◽  
pp. 31-36
Author(s):  
Kanokwan Kanyalert ◽  
Prinya Chindaprasirt ◽  
Duangkanok Tanangteerapong
Keyword(s):  
Weight Loss ◽  
Compressive Strength ◽  
High Temperature ◽  
Fly Ash ◽  
Alkali Activation ◽  
Different Types ◽  
Temperature Exposure ◽  
In Fire ◽  
Thermal Stability Of

This work aims to reveal the effects of zeolite on properties of fly ash based geopolymer under high temperature at 300 °C, 600 °C and 900 °C. The specimens were prepared by alkali activation of fly ash, which was partially replaced by two different types of zeolite at 10%, 20% and 30% by weight. The specimens were analyzed for the maximum compressive strength, weight loss percentage, XRD and SEM. The results highlighted that the percentage of weight loss increased with the ratio of zeolite replacement. The compressive strength of geopolymer with synthetic zeolite and natural zeolite at 7, 28, 60 days were similar. The high-temperature exposure resulted in the reduction in compressive strength in all proportions. At the same temperature, compressive strength of all specimens were not significantly different.

Influence of Particle Size Distribution of Fly Ash on Compressive Strength and Durability of Portland Cement Concrete

2011 ◽  
Vol 685 ◽  
pp. 211-215
Author(s):  
Jian Ping Zhu ◽  
Qi Lei Guo ◽  
Dong Xu Li ◽  
Cun Jun Li
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Power Plants ◽  
Reference Sample ◽  
Chloride Penetration ◽  
Portland Cement Concrete ◽  
Cement Concrete ◽  
Strength And Durability ◽  
Different Content ◽  
Better Than

The Present Research Investigates the Compressive and Durable Properties of Concretes with Fly Ash (FA), a by-Product of Coal-Fired Power Plants. for this Purpose, a Reference Sample and Twenty-one Concretes Containing FA Were Tested. the FA Was Sieved to 200, 300, and 400 Mesh. then FA Was Mixed into Concrete with Different Content. Compressive Strength at 7 and 28 Days, and Chloride Penetration Properties Were Measured. it Is Concluded that FA Can Be Used in the Production of Concrete. in Addition, the FA Concretes Present Satisfactory Physical Properties. when Proper Amount of FA Were Added the Concrete Properties Can Be Better than the Blank one.

scholarly journals Comparison of strength and durability characteristics of a geopolymer produced from fly ash, ground glass fiber and glass powder

2017 ◽  
Vol 67 (328) ◽  
pp. 136 ◽  
Author(s):  
H. Rashidian-Dezfouli ◽  
P. R. Rangaraju
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Portland Cement ◽  
Glass Fiber ◽  
Glass Powder ◽  
Silica Content ◽  
Ground Glass ◽  
Alkali Silica Reaction ◽  
Strength And Durability ◽  
Cement Mixtures

Strength and durability characteristics of geopolymers produced using three precursors, consisting of fly ash, Ground Glass Fiber (GGF), and glass-powder were studied. Combinations of sodium hydroxide and sodium silicate were used as the activator solutions, and the effect of different sodium and silica content of the activators on the workability and compressive strength of geopolymers was investigated. The parameters used in this study were the mass ratio of Na2O-to-binder (for sodium content), and SiO2-to-Na2O of the activator (for silica content). Geopolymer mixtures that achieved the highest compressive strength from each precursor were assessed for their resistance to alkali-silica reaction and compared against the performance of portland cement mixtures. Test results revealed that GGF and fly ash-based geopolymers performed better than glass-powder-based geopolymer mixtures. The resistance of GGF-based and fly ash-based geopolymers to alkali-silica reaction was superior to that of portland cement mixtures, while glass-powder-based geopolymer showed inferior performance.

scholarly journals STRENGTH DEVELOPMENT OF CONCRETE WITH FLY ASH ADDITION

2007 ◽  
Vol 13 (2) ◽  
pp. 115-122 ◽  
Author(s):  
Marta Kosior-Kazberuk ◽  
Małgorzata Lelusz
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Mathematical Models ◽  
Statistical Methods ◽  
Experimental Results ◽  
Strength Development ◽  
Hardened Concrete ◽  
Test Results ◽  
Different Types ◽  
Compressive Strength Of Concrete

Based on experimental results, mathematical models were elaborated to predict the development of compressive strength of concrete with fly ash replacement percentages up to 30 %. Strength of concrete with different types of cement (CEM I 42.5, CEM I 32.5, CEM III 32.5), after 2, 28, 90, 180 days of curing, have been analysed to evaluate the effect of addition content, the time of curing and the type of cement on the compressive strength changes. The adequacy of equations obtained was verified using statistical methods. The test results of selected properties of binders and hardened concrete with fly ash are also included. The analysis showed that concrete with fly ash is characterised by advantageous applicable qualities.

Sign in / Sign up

Export Citation Format

Share Document