scholarly journals Biomechanical Assessment of a Patient-Specific Knee Implant Design Using Finite Element Method

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
Qiguo Rong ◽  
Jianfeng Bai ◽  
Yongling Huang ◽  
Jianhao Lin
Keyword(s):  
Finite Element ◽  
Total Knee Arthroplasty ◽  
Knee Arthroplasty ◽  
Three Dimensional ◽  
Implant Design ◽  
Patient Specific ◽  
Biomechanical Behavior ◽  
Total Knee ◽  
Wear Damage ◽  
Three Dimensional Finite Element

Rheumatoid arthritis is the leading cause of disability in young adults. Total knee arthroplasty has been successfully used to restore the joint function. Due to small bone size, osteoporosis, and severe soft tissue disease, standard knee implant sometimes cannot be directly applied clinically and patient-specific designs may be a more rational choice. The purpose of this study was to evaluate the biomechanical behavior of a patient-specific knee implant. A three-dimensional finite element of total knee arthroplasty was developed. The mechanical strength and the wear damage of the articular surfaces were analyzed. The results show that there exist high risks of component fracture and wear damage; the proposed implant design should be abandoned. The presurgery analysis is helpful in avoiding the potential failure.

scholarly journals Finite-element analysis of the proximal tibial sclerotic bone and different alignment in total knee arthroplasty

2019 ◽  
Vol 20 (1) ◽  
Author(s):  
Ye-Ran Li ◽  
Yu-Hang Gao ◽  
Chen Yang ◽  
Lu Ding ◽  
Xuebo Zhang ◽  
...  
Keyword(s):  
Finite Element ◽  
Total Knee Arthroplasty ◽  
Knee Arthroplasty ◽  
Tibial Plateau ◽  
Three Dimensional ◽  
Genu Varum ◽  
Sclerotic Bone ◽  
Dimensional Measurements ◽  
Tibial Cut ◽  
Total Knee

Abstract Background Despite potential for improving patient outcomes, studies using three-dimensional measurements to quantify proximal tibial sclerotic bone and its effects on prosthesis stability after total knee arthroplasty (TKA) are lacking. Therefore, this study aimed to determine: (1) the distribution range of tibial sclerotic bone in patients with severe genu varum using three-dimensional measurements, (2) the effect of the proximal tibial sclerotic bone thickness on prosthesis stability according to finite-element modelling of TKA with kinematic alignment (KA), mechanical alignment (MA), and 3° valgus alignment, and (3) the effect of short extension stem augment utilization on prosthesis stability. Methods The sclerotic bone in the medial tibial plateau of 116 patients with severe genu varum was measured and classified according to its position and thickness. Based on these cases, finite-element models were established to simulate 3 different tibial cut alignments with 4 different thicknesses of the sclerotic bone to measure the stress distribution of the tibia and tibial prosthesis, the relative micromotion beneath the stem, and the influence of the short extension stem on stability. Results The distribution range of proximal tibial sclerotic bone was at the anteromedial tibial plateau. The models were divided into four types according to the thickness of the sclerotic bone: 15 mm, 10 mm, 5 mm, and 0 mm. The relative micromotion under maximum stress was smallest after MA with no sclerotic bone (3241 μm) and largest after KA with 15 mm sclerotic bone (4467 μm). Relative micromotion was largest with KA and smallest with MA in sclerotic models with the same thickness. Relative micromotion increased as thickness of the sclerotic bone increased with KA and MA (R = 0.937, P = 0.03 and R = 0.756, P = 0.07, respectively). Relative micromotion decreased with short extension stem augment in the KA model when there was proximal tibial sclerotic bone. Conclusions The influence of proximal tibial sclerotic bone on prosthesis’s stability is significant, especially with KA tibial cut. Tibial component’s short extension stem augment can improve stability.

Adoption of Robotic-Arm-Assisted Total Knee Arthroplasty Is Associated with Decreased Use of Articular Constraint and Manipulation under Anesthesia Compared to a Manual Approach

2021 ◽  
Author(s):  
Jenny Zhang ◽  
Chelsea N. Matzko ◽  
Andrew Sawires ◽  
Joseph O. Ehiorobo ◽  
Michael A. Mont ◽  
...  
Keyword(s):  
Total Knee Arthroplasty ◽  
Knee Arthroplasty ◽  
Three Dimensional ◽  
Robotic Arm ◽  
Patient Specific ◽  
Patient Centered ◽  
Lengths Of Stay ◽  
Ligament Balance ◽  
Total Knee ◽  
Early Cohort

AbstractHaptic robotic-arm-assisted total knee arthroplasty (RATKA) seeks to leverage three-dimensional planning, intraoperative assessment of ligament laxity, and guided bone preparation to establish and achieve patient-specific targets for implant position. We sought to compare (1) operative details, (2) knee alignment, (3) recovery of knee function, and (4) complications during adoption of this technique to our experience with manual TKA. We compared 120 RATKAs performed between December 2016 and July 2018 to 120 consecutive manual TKAs performed between May 2015 and January 2017. Operative details, lengths of stay (LOS), and discharge dispositions were collected. Tibiofemoral angles, Knee Society Scores (KSS), and ranges of motion were assessed until 3 months postoperatively. Manipulations under anesthesia, complications, and reoperations were tabulated. Mean operative times were 22 minutes longer in RATKA (p < 0.001) for this early cohort, but decreased by 27 minutes (p < 0.001) from the first 25 RATKA cases to the last 25 RATKA cases. Less articular constraint was used to achieve stability in RATKA (93 vs. 55% cruciate-retaining, p < 0.001; 3 vs. 35% posterior stabilized (PS), p < 0.001; and 4 vs. 10% varus-valgus constrained, p_ = _0.127). RATKA had lower LOS (2.7 vs. 3.4 days, p < 0.001). Discharge dispositions, tibiofemoral angles, KSS, and knee flexion angles did not differ, but manipulations were less common in RATKAs (4 vs. 17%, p = 0.013). We observed less use of constraint, shorter LOS, and fewer manipulations under anesthesia in RATKA, with no increase in complications. Operative times were longer, particularly early in the learning curve, but improved with experience. All measured patient-centered outcomes were equivalent or favored the newer technique, suggesting that RATKA with patient-specific alignment targets does not compromise initial quality. Observed differences may relate to improved ligament balance or diminished need for ligament release.

The Accuracy of Computed Tomography-Based, Three-Dimensional Implant Planning in Robotic-Assisted Total Knee Arthroplasty

2021 ◽  
Author(s):  
Kevin B. Marchand ◽  
Hytham S. Salem ◽  
Kevin K. Mathew ◽  
Steven F. Harwin ◽  
Michael A. Mont ◽  
...  
Keyword(s):  
Computed Tomography ◽  
Total Knee Arthroplasty ◽  
Knee Arthroplasty ◽  
Predictive Accuracy ◽  
Outpatient Surgery ◽  
Three Dimensional ◽  
Patient Specific ◽  
Robotic Assisted ◽  
Preoperative Ct ◽  
Total Knee

AbstractAdvanced imaging used in robotic-assisted total knee arthroplasty (TKA), such as computed tomography (CT)-based three-dimensional (3D) planning, may provide an accurate means of implant sizing preoperatively. The purpose of this study was to examine preoperative CT-based implant planning accuracy for robotic-assisted TKA in patients who have (1) varus deformities, (2) valgus deformities, (3) neutral alignment, and (4) retained hardware. A total of 393 patients underwent a robotic-assisted TKA by a single surgeon received preoperative CT scans. The surgeon reviewed the CT-based model preoperatively and recorded the expected size of the components. The final implants used in each case were recorded and compared with the surgeon's preoperative plan. In all groups of patients, the surgeon's CT-based implant plan was within one size of the implant utilized 100% of the time for both the tibiae and femora. Overall, the surgeon was exactly matched in 319 (81%) and 315 (80%) cases for the femoral and tibial components, respectively. For the femoral component, the mean age for patients in whom the original plan was exactly matched was younger than those whose implants were upsized and older than patients those implants were downsized (p = 0.024). Other patient demographics and preoperative knee alignment were not associated with predictive accuracy for femoral or tibial components. Our results demonstrate how preoperative CT-based, 3D planning for robotic-assisted TKA is accurate to within one size of the components in every case (100%), and exactly matched in 80%. The results of this study are important because they demonstrate how CT-based preoperative implant planning for TKA is reliable and accurate across all native knee alignments and other patient-specific factors. In addition, they build on a previous study by the same single surgeon, demonstrating that predictive ability can improve over time. This may be important as we move toward more outpatient surgery with less ability for prostheses inventory at ambulatory sites.

scholarly journals Patient-specific instrumentation improved three-dimensional accuracy in total knee arthroplasty: a comparative radiographic analysis of 1257 total knee arthroplasties

2019 ◽  
Vol 14 (1) ◽  
Author(s):  
Leo Pauzenberger ◽  
Martin Munz ◽  
Georg Brandl ◽  
Julia K. Frank ◽  
Philipp R. Heuberer ◽  
...  
Keyword(s):  
Total Knee Arthroplasty ◽  
Knee Arthroplasty ◽  
Mechanical Axis ◽  
Three Dimensional ◽  
Mobile Bearing ◽  
Patient Specific ◽  
Limb Alignment ◽  
Patient Specific Instrumentation ◽  
Conventional Instrumentation ◽  
Total Knee

Abstract Background The purpose of this study was to compare restoration of mechanical limb alignment and three-dimensional component-positioning between conventional and patient-specific instrumentation in total knee arthroplasty. Methods Radiographic data of patients undergoing mobile-bearing total knee arthroplasty (n = 1257), using either conventional (n = 442) or patient-specific instrumentation (n = 812), were analyzed. To evaluate accuracy of axis restoration and 3D-component-positioning between conventional and patient-specific instrumentation, absolute deviations from the targeted neutral mechanical limb alignment and planned implant positions were determined. Measurements were performed on standardized coronal long-leg and sagittal knee radiographs. CT-scans were evaluated for accuracy of axial femoral implant rotation. Outliers were defined as deviations from the targeted neutral mechanical axis of > ± 3° or from the intraoperative component-positioning goals of > ± 2°. Deviations greater than ± 5° from set targets were considered to be severe outliers. Results Deviations from a neutral mechanical axis (conventional instrumentation: 2.3°± 1.7° vs. patient-specific instrumentation: 1.7°± 1.2°; p < 0.001) and numbers of outliers (conventional instrumentation: 25.8% vs. patient-specific instrumentation: 10.1%; p < 0.001) were significantly lower in the patient-specific instrumentation group. Significantly lower mean deviations and less outliers were detected regarding 3D-component-positioning in the patient-specific instrumentation compared to the conventional instrumentation group (all p < 0.05). Conclusions Patient-specific instrumentation prevented from severe limb malalignment and component-positioning outliers (> ± 5° deviation). Use of patient-specific instrumentation proved to be superior to conventional instrumentation in achieving more accurate limb alignment and 3D-component positioning, particularly regarding femoral component rotation. Furthermore, the use of patient-specific instrumentation successfully prevented severe (> 5° deviation) outliers.

THE DEVELOPMENT OF A PATIENT-SPECIFIC FINITE ELEMENT MODEL OF A PAINFUL TOTAL KNEE ARTHROPLASTY

2012 ◽  
Vol 45 ◽  
pp. S384
Author(s):  
Richard T Keller ◽  
Michael T Hirschmann ◽  
Niklaus F Friederich ◽  
Ulrich N Hansen ◽  
Andrew A Amis
Keyword(s):  
Finite Element ◽  
Total Knee Arthroplasty ◽  
Finite Element Model ◽  
Knee Arthroplasty ◽  
Element Model ◽  
Patient Specific ◽  
Total Knee

A Finite-Element Study of Metal Backing and Tibial Resection Depth in a Composite Tibia Following Total Knee Arthroplasty

2016 ◽  
Vol 138 (4) ◽  
Author(s):  
Susumu Tokunaga ◽  
Renee D. Rogge ◽  
Scott R. Small ◽  
Michael E. Berend ◽  
Merrill A. Ritter
Keyword(s):  
Finite Element ◽  
Total Knee Arthroplasty ◽  
Knee Arthroplasty ◽  
Implant Design ◽  
Bone Resection ◽  
Element Analysis ◽  
Term Survival ◽  
Tibial Resection ◽  
Total Knee ◽  
Resection Depth

Prosthetic alignment, patient characteristics, and implant design are all factors in long-term survival of total knee arthroplasty (TKA), yet the level at which each of these factors contribute to implant loosening has not been fully described. Prior clinical and biomechanical studies have indicated tibial overload as a cause of early TKA revision. The purpose of this study was to determine the relationship between tibial component design and bone resection on tibial loading. Finite-element analysis (FEA) was performed after simulated implantation of metal backed (MB) and all-polyethylene (AP) TKA components in 5 and 15 mm of tibial resection into a validated intact tibia model. Proximal tibial strains significantly increased between 13% and 199% when implanted with AP components (p < 0.05). Strain significantly increased between 12% and 209% in the posterior tibial compartment with increased bone resection (p < 0.05). This study indicates elevated strains in AP implanted tibias across the entirety of the proximal tibial cortex, as well as a posterior shift in tibial loading in instances of increased resection depth. These results are consistent with trends observed in prior biomechanical studies and may associate the documented device history of tibial collapse in AP components with increased bone strain and overload beneath the prosthesis.

Effect of post-cam design on the kinematics and contact stress of posterior-stabilized total knee arthroplasty

2021 ◽  
pp. 1-10
Author(s):  
Jin-Ah Lee ◽  
Yong-Gon Koh ◽  
Kyoung-Tak Kang
Keyword(s):  
Finite Element ◽  
Total Knee Arthroplasty ◽  
Contact Stress ◽  
Knee Arthroplasty ◽  
Gait Cycle ◽  
Three Dimensional ◽  
Posterior Stabilized ◽  
Cam Mechanism ◽  
Total Knee ◽  
Tibial Translation

BACKGROUND: The post-cam mechanism in the posterior-stabilized (PS) implant plays an important role, such as durability and kinematic performances, in total knee arthroplasty (TKA). OBJECTIVE: The purpose of this study was to evaluate the difference in the kinematics and contact stress of five post-cam designs, which are flat-and-flat, curve-and-curve (concave), curve-and-curve (concave and convex), helical, and asymmetrical post-cam designs, using three-dimensional finite element models. METHODS: We designed the post-cam model with five different geometries. The kinematics, contact stress, and contact area were evaluated in the five post-cam designs under gait cycle loading conditions using the finite element method. RESULTS: There were no differences in the contact stress and area on the tibial insert in all designs. The largest internal rotation was shown in the swing phase for the helical design, and the largest tibial posterior translation was observed for the curve-and-curve (concave) design. The curve-and-curve (concave) design showed the lowest contact stress and the largest posterior tibial translation during the gait cycle. CONCLUSIONS: Considering the kinematics and contact stress, we found that the curve-and-curve (concave) design was more stable than other designs. From the results, we found the important factors of TKA implant considering stability and kinematics.

Changes in knee shape and geometry resulting from total knee arthroplasty

2017 ◽  
Vol 232 (1) ◽  
pp. 67-79 ◽  
Author(s):  
Mohsen Akbari Shandiz ◽  
Paul Boulos ◽  
Stefan Karl Saevarsson ◽  
Heiko Ramm ◽  
Chun Kit (Jack) Fu ◽  
...  
Keyword(s):  
Total Knee Arthroplasty ◽  
Knee Arthroplasty ◽  
Three Dimensional ◽  
Implant Design ◽  
Limiting Factor ◽  
Sample Population ◽  
Stability Range ◽  
Study Objective ◽  
Implant Selection ◽  
Total Knee

Changes in knee shape and geometry resulting from total knee arthroplasty can affect patients in numerous important ways: pain, function, stability, range of motion, and kinematics. Quantitative data concerning these changes have not been previously available, to our knowledge, yet are essential to understand individual experiences of total knee arthroplasty and thereby improve outcomes for all patients. The limiting factor has been the challenge of accurately measuring these changes. Our study objective was to develop a conceptual framework and analysis method to investigate changes in knee shape and geometry, and prospectively apply it to a sample total knee arthroplasty population. Using clinically available computed tomography and radiography imaging systems, the three-dimensional knee shape and geometry of nine patients (eight varus and one valgus) were compared before and after total knee arthroplasty. All patients had largely good outcomes after their total knee arthroplasty. Knee shape changed both visually and numerically. On average, the distal condyles were slightly higher medially and lower laterally (range: +4.5 mm to −4.4 mm), the posterior condyles extended farther out medially but not laterally (range: +1.8 to −6.4 mm), patellofemoral distance increased throughout flexion by 1.8–3.5 mm, and patellar thickness alone increased by 2.9 mm (range: 0.7–5.2 mm). External femoral rotation differed preop and postop. Joint line distance, taking cartilage into account, changed by +0.7 to −1.5 mm on average throughout flexion. Important differences in shape and geometry were seen between pre-total knee arthroplasty and post-total knee arthroplasty knees. While this is qualitatively known, this is the first study to report it quantitatively, an important precursor to identifying the reasons for the poor outcome of some patients. Using the developed protocol and visualization techniques to compare patients with good versus poor clinical outcomes could lead to changes in implant design, implant selection, component positioning, and surgical technique. Recommendations based on this sample population are provided. Intraoperative and postoperative feedback could ultimately improve patient satisfaction.

Sign in / Sign up

Export Citation Format

Share Document