scholarly journals Liquid Mass Sensing Using Resonating Microplates under Harsh Drop and Spray Conditions

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Said Mahajne ◽  
Dafne Guetta ◽  
Stella Lulinsky ◽  
Slava Krylov ◽  
Yoav Linzon
Keyword(s):  
Resonant Frequency ◽  
Resonant Mode ◽  
Ambient Conditions ◽  
Mass Sensing ◽  
Operation Conditions ◽  
Multiple Cycles ◽  
Volatile Liquids ◽  
Deposited Film ◽  
Harsh Conditions

We have performed in situ real time mass sensing of deposited liquid volatile droplets and sprays using plate-like microstructures, with robust and reusable performance attained over harsh conditions and multiple cycles of operation. A home-built electrooptical sensing system in ambient conditions has been used. The bimorph effect on the resonant frequency of altered mass loading, elasticity, and strain had been carefully compared, and the latter were found to be negligible in the presence of nonviscous liquids deposited on top of our microplate devices. In resonant mode, the loaded mass has been estimated from measured resonant frequency shifts and interpreted from a simple, uniformly deposited film model. A minimum submicrogram detectable mass was estimated, suggesting the system’s potential for robust, fast, and reusable sensing capabilities, in the presence of volatile liquids under harsh operation conditions.

Decay Method for Measuring Complex Dielectric Constants During Microwave Processing

1994 ◽  
Vol 347 ◽  
Author(s):  
O. Iny ◽  
M. Barmatz
Keyword(s):  
Resonant Frequency ◽  
Quality Factor ◽  
Modulation Frequency ◽  
Resonant Mode ◽  
Dielectric Constants ◽  
Sample Temperature ◽  
Cavity Modes ◽  
Sample Support ◽  
Quality Factor Q

ABSTRACTWe have developed a fast in-situ method for measuring the quality factor, Q, and resonant frequency, fr, for an isolated microwave resonant mode. The mode resonant frequency was continuously monitored using a phase modulation frequency tracking technique. The quality factor was determined by periodically switching off the microwave power and fitting the decay curve to an exponential. The cavity perturbation method was used with small spherical samples (ka « 1). Combining the Q and fr data with a non-contact measurement of the sample temperature permits the calculation of the temperature dependence of the real (ε′) and imaginary (ε″) dielectric constants. Because of the speed of this technique (≈1 μSce), it can be used during processing to continuously measure the dielectric constants of the material without perturbing the sample temperature. Measurements were performed using isolated TM010 and TEI11 cylindrical cavity modes. Care was taken to minimize the perturbing effects of the sample support. The accuracy of the frequency tracker was verified at room temperature from measurements on several alumina spherical samples. The decay technique was also verified from measurements on several small spherical nylon samples.

A Mild and Simple Method for Making MIDA Boronates

2020 ◽  
Author(s):  
Aidan Kelly ◽  
Peng-Jui (Ruby) Chen ◽  
Jenna Klubnick ◽  
Daniel J. Blair ◽  
Martin D. Burke
Keyword(s):  
Organic Synthesis ◽  
Boronic Acids ◽  
Simple Method ◽  
Direct Preparation ◽  
Synthesis Procedure ◽  
Harsh Conditions

<div> <div> <div> <p>Existing methods for making MIDA boronates require harsh conditions and complex procedures to achieve dehydration. Here we disclose that a pre-dried form of MIDA, MIDA anhydride, acts as both a source of the MIDA ligand and an in situ desiccant to enable a mild and simple MIDA boronate synthesis procedure. This method expands the range of sensitive boronic acids that can be converted into their MIDA boronate counterparts. Further utilizing unique properties of MIDA boronates, we have developed a MIDA Boronate Maker Kit which enables the direct preparation and purification of MIDA boronates from boronic acids using only heating and centrifuge equipment that is widely available in labs that do not specialize in organic synthesis. </p> </div> </div> </div>

scholarly journals Diffusion-induced in situ growth of covalent organic frameworks for composite membranes

2019 ◽  
Vol 7 (45) ◽  
pp. 25802-25807 ◽  
Author(s):  
Priyanka Manchanda ◽  
Stefan Chisca ◽  
Lakshmeesha Upadhyaya ◽  
Valentina-Elena Musteata ◽  
Mark Carrington ◽  
...  
Keyword(s):  
Reaction Times ◽  
Composite Membranes ◽  
Thin Layers ◽  
In Situ Growth ◽  
Covalent Organic Frameworks ◽  
Polymeric Support ◽  
Ambient Conditions ◽  
Induction Method ◽  
Covalent Organic Framework

Thin layers of a covalent organic framework (COF) have been synthesized on a flexible polymeric support using a new diffusion-induction method under ambient conditions in reaction times as short as 3 hours.

Measurement of Cement in Situ Stresses and Mechanical Properties Without Cooling or Depressurization

2021 ◽  
Author(s):  
Meng Meng ◽  
Luke Frash ◽  
James Carey ◽  
Wenfeng Li ◽  
Nathan Welch ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Property ◽  
Elastic Modulus ◽  
Poisson’S Ratio ◽  
Axial Stress ◽  
Triaxial Compression ◽  
In Situ Measurement ◽  
Poisson's Ratio ◽  
Ambient Conditions

Abstract Accurate characterization of oilwell cement mechanical properties is a prerequisite for maintaining long-term wellbore integrity. The drawback of the most widely used technique is unable to measure the mechanical property under in situ curing environment. We developed a high pressure and high temperature vessel that can hydrate cement under downhole conditions and directly measure its elastic modulus and Poisson's ratio at any interested time point without cooling or depressurization. The equipment has been validated by using water and a reasonable bulk modulus of 2.37 GPa was captured. Neat Class G cement was hydrated in this equipment for seven days under axial stress of 40 MPa, and an in situ measurement in the elastic range shows elastic modulus of 37.3 GPa and Poisson's ratio of 0.15. After that, the specimen was taken out from the vessel, and setted up in the triaxial compression platform. Under a similar confining pressure condition, elastic modulus was 23.6 GPa and Possion's ratio was 0.26. We also measured the properties of cement with the same batch of the slurry but cured under ambient conditions. The elastic modulus was 1.63 GPa, and Poisson's ratio was 0.085. Therefore, we found that the curing condition is significant to cement mechanical property, and the traditional cooling or depressurization method could provide mechanical properties that were quite different (50% difference) from the in situ measurement.

scholarly journals Characterization of interferences to in situ observations of <i>δ</i><sup>13</sup>CH<sub>4</sub> and C<sub>2</sub>H<sub>6</sub> when using a cavity ring-down spectrometer at industrial sites

2017 ◽  
Vol 10 (6) ◽  
pp. 2077-2091 ◽  
Author(s):  
Sabina Assan ◽  
Alexia Baudic ◽  
Ali Guemri ◽  
Philippe Ciais ◽  
Valerie Gros ◽  
...  
Keyword(s):  
Near Infrared ◽  
Field Tests ◽  
Isotopic Signature ◽  
Ambient Conditions ◽  
Industrial Sites ◽  
Source Determination ◽  
Infrared Spectral ◽  
The Subject

Abstract. Due to increased demand for an understanding of CH4 emissions from industrial sites, the subject of cross sensitivities caused by absorption from multiple gases on δ13CH4 and C2H6 measured in the near-infrared spectral domain using CRDS has become increasingly important. Extensive laboratory tests are presented here, which characterize these cross sensitivities and propose corrections for the biases they induce. We found methane isotopic measurements to be subject to interference from elevated C2H6 concentrations resulting in heavier δ13CH4 by +23.5 ‰ per ppm C2H6 ∕ ppm CH4. Measured C2H6 is subject to absorption interference from a number of other trace gases, predominantly H2O (with an average linear sensitivity of 0.9 ppm C2H6 per  % H2O in ambient conditions). Yet, this sensitivity was found to be discontinuous with a strong hysteresis effect and we suggest removing H2O from gas samples prior to analysis. The C2H6 calibration factor was calculated using a GC and measured as 0.5 (confirmed up to 5 ppm C2H6). Field tests at a natural gas compressor station demonstrated that the presence of C2H6 in gas emissions at an average level of 0.3 ppm shifted the isotopic signature by 2.5 ‰, whilst after calibration we find that the average C2H6 : CH4 ratio shifts by +0.06. These results indicate that, when using such a CRDS instrument in conditions of elevated C2H6 for CH4 source determination, it is imperative to account for the biases discussed within this study.

Chromic Polydiacetylene Single Crystals: Atomic Force Microscopy Studies

1995 ◽  
Vol 413 ◽  
Author(s):  
V. Shivshankar ◽  
C. Sung ◽  
J. Kumar ◽  
S. K. Tripathy ◽  
D. J. Sandman
Keyword(s):  
Atomic Force Microscopy ◽  
Surface Morphology ◽  
Single Crystals ◽  
Ambient Conditions ◽  
Free Standing ◽  
Force Microscopy ◽  
Sensor Performance ◽  
Atomic Force ◽  
Variable Surface

ABSTRACTWe have studied the surface morphology of free standing single crystals of thermochromic polydiacetylenes (PDAs), namely, ETCD and IPUDO (respectively, the ethyl and isopropyl urethanes of 5,7-dodecadiyn-1,12-diol), by Atomic Force Microscopy (AFM) under ambient conditions. Micron scale as well as molecularly resolved images were obtained. The micron scale images indicate a variable surface, and the molecularly resolved images show a well defined 2-D lattice that is interpreted in terms of molecular models and known crystallographic data. Thereby information about surface morphology, which is crucial to potential optical device or chromic sensor performance is available. We also report the observation of a “macroscopic shattering” of the IPUDO monomer crystal during in-situ UV polymerization studies.

scholarly journals Dynamic Characterization of Biosensing MEMS Cantilevers with Different Position of the Driving Electrode—Vacuum Response Versus Ambient Conditions

2021 ◽  
Vol 4 (1) ◽  
pp. 30
Author(s):  
Marius Pustan ◽  
Corina Birleanu ◽  
Florina Serdean
Keyword(s):  
Dynamic Response ◽  
Resonant Frequency ◽  
Operating Conditions ◽  
Laser Vibrometer ◽  
Electrode Position ◽  
Ambient Conditions ◽  
Biological Detection ◽  
Lower Electrode ◽  
Mems Resonators ◽  
Mems Cantilevers

The influence of the driving electrode positions on the dynamic response of polysilicon MEMS resonators used in biosensing applications is studied as a function of the operating conditions (vacuum versus free-air operating mode). The scope of this research work is orientated towards identifying the effect of driving electrode position on the dynamic response of sensing MEMS used in biomass detection. The mass-deposition detection is based on the change in the resonant frequency of vibrating elements considering a biological detection film deposited on the oscillating structure. The operating conditions, such as medium pressure, change the behavior of the dynamic response including the resonant frequency, the amplitude, and the velocity of oscillations as well as the quality factor and the loss of energy. The change in the dynamic response of the investigated MEMS cantilevers as a function of the lower electrode position and operating conditions is evaluated using a Polytec Laser Vibrometer. The decrease in the amplitude and velocity of the oscillations if the lower electrode is moved from the beam free-end toward the beam anchor is experimentally monitored. The changes in the response of samples in vacuum are slightly influenced by the electrode position compared with the response of the same sample in ambient conditions. Moreover, the effect of oscillating modes (first, second and third modes) is taken into consideration to improve the dynamical detection of the investigated samples. The obtained results indicate that different responses of MEMS resonators can be achieved if the position of the driving electrode is moved from the cantilever free-end toward the anchor. Indeed, the resonator stiffness, velocity and amplitude of oscillations are significantly modified for samples oscillating in ambient conditions for biological detection compared with their response in vacuum.

Sign in / Sign up

Export Citation Format

Share Document