scholarly journals Loading and Contact Stress Analysis on the Thread Teeth in Tubing and Casing Premium Threaded Connection

2014 ◽  
Vol 2014 ◽  
pp. 1-11 ◽  
Author(s):  
Honglin Xu ◽  
Taihe Shi ◽  
Zhi Zhang ◽  
Bin Shi
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Analytical Model ◽  
Contact Stress ◽  
Analytical Method ◽  
Service Level ◽  
Element Analysis ◽  
Threaded Connection ◽  
Threaded Connections ◽  
Set Up

Loading and contact stress distribution on the thread teeth in tubing and casing premium threaded connections are of great importance for design optimization, pretightening force control, and thread failure prevention. This paper proposes an analytical method based on the elastic mechanics. This is quite different from other papers, which mainly rely on finite element analysis. The differential equation of load distribution on the thread teeth was established according to equal pitch of the engaged thread after deformation and solved by finite difference method. Furthermore, the relation between load acting on each engaged thread and mean contact stress on its load flank is set up based on the geometric description of thread surface. By comparison, this new analytical method with the finite element analysis for a modified API 177.8 mm premium threaded connection is approved. Comparison of the contact stress on the last engaged thread between analytical model and FEM shows that the accuracy of analytical model will decline with the increase of pretightening force after the material enters into plastic deformation. However, the analytical method can meet the needs of engineering to some extent because its relative error is about 6.2%~18.1% for the in-service level of pretightening force.

Based on ANSYS Planetary Gear Ransmission Design Analysis

2011 ◽  
Vol 314-316 ◽  
pp. 1218-1221
Author(s):  
Hao Min Huang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Contact Stress ◽  
Planetary Gear ◽  
Design Analysis ◽  
Ansys Software ◽  
Element Analysis ◽  
Planet Gear ◽  
Gear Contact ◽  
Transmission Gear

Conventional methods of design to be completed ordinary hydraulic transmission gear gearbox design, but for such a non-planet-rule entity, and the deformation of the planet-gear contact stress will have a great impact on the planet gear, it will be very difficult According to conventional design. In this paper, ANSYS software to the situation finite element analysis, the planetary gear to simulate modeling study.

Design a Kind of Oblique-Cone-Sliding-Ring Assembly Seal Device

2014 ◽  
Vol 496-500 ◽  
pp. 1007-1011
Author(s):  
Jian Hua Fang ◽  
Wei Yan
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Work Stress ◽  
Contact Stress ◽  
Element Analysis ◽  
Ring Assembly ◽  
User Demand ◽  
Oblique Cone

The design of seal device that can be used in carbide actor is a real problems.This paper presents a kind of oblique-cone-slid-ring (OCSR) assembly seal device that can self-compensate the seal wear in application. The max contact stress on the seal surface and other contact face is far bigger than the work stress of sealed medium in carbide actor. That means the design satisfies the user demand . Keywords: oblique-cone-sliding-ring (OCSR) assembly seal; self-compensation to seal wear; finite element analysis; contact stress;

scholarly journals Stiffness prediction for bolted moment-connections in cold-formed steel trusses

2020 ◽  
Vol 41 (1) ◽  
Author(s):  
Apai Benchaphong ◽  
Rattanasak Hongthong ◽  
Sutera Benchanukrom ◽  
Nirut Konkong
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Analytical Method ◽  
Truss Structures ◽  
Rotational Stiffness ◽  
Element Analysis ◽  
Moment Connection ◽  
Rigid Connection ◽  
Cold Formed Steel ◽  
Steel Trusses

The purpose of this research was to study the behavior of cold-formed steel cantilever truss structures. A cantilever truss structure and bolt-moment connection were tested and verified by the 3D-finite element model. The verification results showed a good correlation between an experimental test and finite element analysis. An analytical method for elastic rotational stiffness of bolt-moment connection was proposed. The equation proposed in the analytical method was used to approximate the elastic rotational stiffness of the bolt group connection, and was also applied to the Richard-Abbott model for generating the nonlinear moment-rotation curve which modeled the semi-rigid connection stiffness. The 2D-finite element analysis was applied to study the behavior of the truss connection, caused by semi-rigid connection stiffness which caused a change of force to the truss elements. The results showed that the force in the structural members increased by between 13.62%-74.32% of the axial forces, and the bending moment decreased by between 33.05%-100%. These results strongly suggest that the semi-rigid connection between cold-formed steel cantilever truss structures should be considered in structural analysis to achieve optimum design, acknowledging this as the real behavior of the structure.

Finite Element Analysis for Gear Contact Based on UG and ABAQUS

2013 ◽  
Vol 442 ◽  
pp. 229-232 ◽  
Author(s):  
Li Mei Wu ◽  
Fei Yang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Contact Stress ◽  
Three Dimensional ◽  
Element Model ◽  
Tooth Surface ◽  
Element Analysis ◽  
Tooth Width ◽  
Gear Contact ◽  
Maximum Contact

According to the cutting theory of involute tooth profile, established an exact three-dimensional parametric model by UG. Used ABAQUS to crate finite element model for gear meshing. After simulated the meshing process, discussed the periodicity of the tooth surface contact stress. Based on the result of finite element analysis, made a comparison of the maximum contact stress between finite element solution and Hertz theoretical solution, analyzed the contact stress distribution on tooth width, and researched the effect of friction factor on contact stress. All that provided some theoretical basis for gear contact strength design.

Finite Element Analysis and Topology Optimization of the Clamping Unit in a Two-Platen Injection Machine

2011 ◽  
Vol 117-119 ◽  
pp. 1535-1542 ◽  
Author(s):  
Hua Wei Zhang ◽  
Wei Xia ◽  
Zhi Heng Wu
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Topology Optimization ◽  
Element Model ◽  
Molding Machine ◽  
Element Analysis ◽  
And Topology ◽  
The Finite Element Analysis ◽  
Set Up ◽  
The Finite Element Model

In this paper, the clamping unit of a two-platen injection molding machine was modeled by Pro/ENGINEER, and was imported to Altair HyperWorks. In HyperMesh module, the finite element model was set up, ANSYS has been used in the finite element analysis of the clamping unit and the deformation and stress results were obtained. Based on the topology optimization of HyperWorks/OptiStruct, recommendations to improve the structure of the clamping mechanism are presented; the results showed that less material was used while its performance was maintained.

Research on Pulley Strain of Metal Belt CVT

2014 ◽  
Vol 952 ◽  
pp. 249-252
Author(s):  
Wu Zhang ◽  
Wei Guo ◽  
Fa Rong Kou ◽  
Yi Zhi Yang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Analytical Method ◽  
Compressive Strain ◽  
Continuously Variable Transmission ◽  
Transmission Ratio ◽  
Element Analysis ◽  
Variable Transmission

Pulley strain aggravated whole-Part abrasion, affected friction and lubricates state of metal belt continuously variable transmission. Pulley strain was analyzed by analytical method and finite element analysis. The results indicate that with the increase of transmission ratio, the driver pulley compressive strain is increases after reduces for a while, and the driven pulley increase. Compressive strain dense when radius is lesser and vice versa. Two methods results are basically the same, whereby demonstrating that the model is rational and that the analysis results are reliable.

Sign in / Sign up

Export Citation Format

Share Document