scholarly journals Optimization Study in Biodiesel Production via Response Surface Methodology Using Dolomite as a Heterogeneous Catalyst

2014 ◽  
Vol 2014 ◽  
pp. 1-11 ◽  
Author(s):  
Regina C. R. Santos ◽  
Rômulo B. Vieira ◽  
Antoninho Valentini
Keyword(s):  
Response Surface Methodology ◽  
Soybean Oil ◽  
Response Surface ◽  
Heterogeneous Catalyst ◽  
Methyl Esters ◽  
Operating Conditions ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
High Catalytic Activity ◽  
Calcium Leaching

A carbonate mineral, dolomite, was used as a heterogeneous catalyst to produce methyl-esters from soybean oil. The samples were analyzed by XRF, TGA, XRD, TPD-CO2, and SEM. The calcination of dolomite at 800°C/1 h resulted in a highly active mixed metal oxides. In addition, the influence of the reaction variables such as the temperature, catalyst amount, and methanol/soybean oil molar ratio in methyl-ester production was optimized by the application of a central composite design in conjunction with the response surface methodology (RSM). The XRF analysis is carried out after the reuses procedure which shows that the deactivation process is mainly due to the selective calcium leaching. Overall, the calcined dolomite exhibited high catalytic activity at moderate operating conditions for biodiesel production.

scholarly journals Optimization of an Ultrasonic-Assisted Biodiesel Production Process from One Genotype of Rapeseed (TERI (OE) R-983) as a Novel Feedstock Using Response Surface Methodology

Energies ◽  
2019 ◽  
Vol 12 (14) ◽  
pp. 2656 ◽  
Author(s):  
Sara Almasi ◽  
Barat Ghobadian ◽  
Gholam Hassan Najafi ◽  
Talal Yusaf ◽  
Masoud Dehghani Soufi ◽  
...  
Keyword(s):  
Response Surface Methodology ◽  
Reaction Time ◽  
Response Surface ◽  
Methyl Esters ◽  
Operating Conditions ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Climate Conditions ◽  
Ultrasonic Assisted ◽  
Optimized Conditions

In recent years, due to the favorable climate conditions of Iran, the cultivation of rapeseed has increased significantly. The aim of this study was to investigate the possibility of biodiesel production from one genotype of rapeseed (TERI (OE) R-983). An ultrasonic approach was used in order to intensify the reaction. Response surface methodology (RSM) was applied to identify the optimum conditions of the process. The results of this research showed that the conversion of biodiesel was found to be 87.175% under the optimized conditions of a 4.63:1 molar ratio (methanol to oil), 56.50% amplitude, and 0.4 s pulses for a reaction time of 5.22 min. Increasing the operating conditions, such as the molar ratio from 4:1 to 5.5:1, amplitude from 50% to 72.5%, reaction time from 3 min to 7 min, and pulse from 0.4 s to 1 s, increased the FAME (fatty acid methyl esters) yield by approximately 4.5%, 2.3%, 1.2%, and 0.5%, respectively. The properties of the TERI (OE) R-983 methyl ester met the requirements of the biodiesel standard (ASTM D6751), indicating the potential of the produced biodiesel as an alternative fuel.

Application of Response Surface Methodology for Optimization of Biodiesel Production from Microalgae Through Nanocatalytic Transesterification Process.

2021 ◽  
Author(s):  
Vaishali Mittal ◽  
Uttam Kumar Ghosh
Keyword(s):  
Response Surface Methodology ◽  
Reaction Time ◽  
Response Surface ◽  
Process Parameters ◽  
Reaction Temperature ◽  
Methyl Esters ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Impregnation Method ◽  
The Impact

Abstract Production of biodiesel from microalgae is gaining popularity since it does not compromise food security or the global economy. This article reports biodiesel production with Spirulina microalgae through nanocatalytic transesterification process. The nanocatalyst calcium methoxide Ca(OCH3)2 was synthesized using wet impregnation method and utilized to carry out the transesterification process. The nanocatalyst was characterized to evaluate its structural and spectral characteristics using different characterization techniques such as Thermogravimetric analysis (TGA), X-ray diffraction (XRD), Scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), and Brunaeur-Emmett-Teller(BET) measurement for surface area. The result demonstrates that calcium methoxide Ca(OCH3)2 possesses a high catalytic activity compared to a heterogeneous catalyst such as calcium oxide (CaO). The impact of several process parameters such as reaction temperature, the molar ratio of methanol to oil, catalyst concentration, and reaction time used in the transesterification process was optimized by employing central composite design(CCD) based response surface methodology(RSM). The polynomial regression equation of second order was obtained for methyl esters. The model projected a 99% fatty acid methyl esters (FAME) yield for optimal process parameters of reaction time 3hrs,3 wt.% of Ca(OCH3)2 catalyst loading, 80°C reaction temperature, and 30:1 methanol to oil molar ratio.

Optimization of biodiesel synthesis under simultaneous ultrasound-microwave irradiation using response surface methodology (RSM)

2015 ◽  
Vol 4 (4) ◽  
Author(s):  
Seyed Mohammad Safieddin Ardebili ◽  
Teymor Tavakoli Hashjin ◽  
Barat Ghobadian ◽  
Gholamhasan Najafi ◽  
Stefano Mantegna ◽  
...  
Keyword(s):  
Response Surface Methodology ◽  
Microwave Irradiation ◽  
Response Surface ◽  
Palm Oil ◽  
Catalyst Concentration ◽  
Irradiation Time ◽  
Operating Conditions ◽  
Molar Ratio ◽  
Reaction Conditions ◽  
Biodiesel Synthesis

AbstractThis work investigates the effect of simultaneous ultrasound-microwave irradiation on palm oil transesterification and uncovers optimal operating conditions. Response surface methodology (RSM) has been used to analyze the influence of reaction conditions, including methanol/palm oil molar ratio, catalyst concentration, reaction temperature and irradiation time on biodiesel yield. RSM analyses indicate 136 s and 129 s as the optimal sonication and microwave irradiation times, respectively. Optimized parameters for full conversion (97.53%) are 1.09% catalyst concentration and a 7:3.1 methanol/oil molar ratio at 58.4°C. Simultaneous ultrasound-microwave irradiation dramatically accelerates the palm oil transesterification reaction. Pure biodiesel was obtained after only 2.2 min while the conventional method requires about 1 h.

Evaluation of heterogeneous photo-Fenton oxidation of Orange II using response surface methodology

2010 ◽  
Vol 62 (6) ◽  
pp. 1320-1326 ◽  
Author(s):  
Y. H. Gong ◽  
H. Zhang ◽  
Y. L. Li ◽  
L. J. Xiang ◽  
S. Royer ◽  
...  
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Heterogeneous Catalyst ◽  
Uv Irradiation ◽  
Heterogeneous Catalysts ◽  
Ph Value ◽  
Dye Degradation ◽  
High Catalytic Activity ◽  
Orange Ii ◽  
Initial Ph

A mesoporous SBA-15 doped iron oxide (Fe2O3/SBA-15) was synthesized by co-codensation, characterized and used as heterogeneous catalysts for the photo-Fenton decolorization of azo dye Orange II under UV irradiation. Response surface methodology (RSM) was used to investigate operating condition effects, such as hydrogen peroxide concentration, initial pH and catalyst loadings, on the decolorization rate. UV irradiation is found to enhance the activity of the catalyst in the process. RSM analysis evidenced the influence of the initial pH value and H2O2 concentration on the dye degradation rate. The coupled UV/Fe2O3/SBA-15/H2O2 process at room temperature is revealed as a promising friendly process for wastewater treatment. Indeed, the use of a heterogeneous catalyst allows an easy active phase recycling without multi-step recovering while the heterogeneous catalyst used here exhibits high catalytic activity for the reaction considered.

Optimization of melon oil methyl ester production using response surface methodology

2017 ◽  
Vol 2 (1) ◽  
pp. 1-10 ◽  
Author(s):  
O. S. Aliozo ◽  
L. N. Emembolu ◽  
O. D. Onukwuli
Keyword(s):  
Response Surface Methodology ◽  
Reaction Time ◽  
Methyl Ester ◽  
Response Surface ◽  
Research Work ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Reaction Conditions ◽  
Central Composite Designs ◽  
American Society

Abstract In this research work, melon oil was used as feedstock for methyl ester production. The research was aimed at optimizing the reaction conditions for methyl ester yield from the oil. Response surface methodology (RSM), based on a five level, four variable central composite designs (CCD)was used to optimize and statistically analyze the interaction effect of the process parameter during the biodiesel production processes. A total of 30 experiments were conducted to study the effect of methanol to oil molar ratio, catalyst weight, temperature and reaction time. The optimal yield of biodiesel from melon oil was found to be 94.9% under the following reaction conditions: catalyst weight - 0.8%, methanol to oil molar ratio - 6:1, temperature - 55°C and reaction time of 60mins. The quality of methyl ester produced at these conditions was within the American Society for Testing and Materials (ASTM D6751) specification.

scholarly journals Response Surface Methodology for Biodiesel Production Using Calcium Methoxide Catalyst Assisted with Tetrahydrofuran as Cosolvent

2017 ◽  
Vol 2017 ◽  
pp. 1-9 ◽  
Author(s):  
Nichaonn Chumuang ◽  
Vittaya Punsuvon
Keyword(s):  
Response Surface Methodology ◽  
Reaction Time ◽  
Response Surface ◽  
Catalyst Concentration ◽  
Acid Methyl Ester ◽  
Waste Cooking Oil ◽  
Biodiesel Production ◽  
Quadratic Model ◽  
Molar Ratio ◽  
Standard Requirement

The present study was performed to optimize a heterogeneous calcium methoxide (Ca(OCH3)2) catalyzed transesterification process assisted with tetrahydrofuran (THF) as a cosolvent for biodiesel production from waste cooking oil. Response surface methodology (RSM) with a 5-level-4-factor central composite design was applied to investigate the effect of experimental factors on the percentage of fatty acid methyl ester (FAME) conversion. A quadratic model with an analysis of variance obtained from the RSM is suggested for the prediction of FAME conversion and reveals that 99.43% of the observed variation is explained by the model. The optimum conditions obtained from the RSM were 2.83 wt% of catalyst concentration, 11.6 : 1 methanol-to-oil molar ratio, 100.14 min of reaction time, and 8.65% v/v of THF in methanol concentration. Under these conditions, the properties of the produced biodiesel satisfied the standard requirement. THF as cosolvent successfully decreased the catalyst concentration, methanol-to-oil molar ratio, and reaction time when compared with biodiesel production without cosolvent. The results are encouraging for the application of Ca(OCH3)2 assisted with THF as a cosolvent for environmentally friendly and sustainable biodiesel production.

scholarly journals Study of Soybean Oil Hydrolysis Catalyzed by Thermomyces lanuginosus Lipase and Its Application to Biodiesel Production via Hydroesterification

2011 ◽  
Vol 2011 ◽  
pp. 1-8 ◽  
Author(s):  
Elisa d'Avila Cavalcanti-Oliveira ◽  
Priscila Rufino da Silva ◽  
Alessandra Peçanha Ramos ◽  
Donato Alexandre Gomes Aranda ◽  
Denise Maria Guimarães Freire
Keyword(s):  
Soybean Oil ◽  
Methyl Esters ◽  
Reaction Medium ◽  
Acid Catalyst ◽  
Biodiesel Production ◽  
Thermomyces Lanuginosus ◽  
Molar Ratio ◽  
Esterification Reaction ◽  
Thermomyces Lanuginosus Lipase ◽  
Niobic Acid

The process of biodiesel production by the hydroesterification route that is proposed here involves a first step consisting of triacylglyceride hydrolysis catalyzed by lipase from Thermomyces lanuginosus (TL 100L) to generate free fatty acids (FFAs). This step is followed by esterification of the FFAs with alcohol, catalyzed by niobic acid in pellets or without a catalyst. The best result for the enzyme-catalyzed hydrolysis was obtained under reaction conditions of 50% (v/v) soybean oil and 2.3% (v/v) lipase (25 U/mL of reaction medium) in distilled water and at 60∘C; an 89% conversion rate to FFAs was obtained after 48 hours of reaction. For the esterification reaction, the best result was with an FFA/methanol molar ratio of 1:3, niobic acid catalyst at a concentration of 20% (w/w FFA), and 200∘C, which yielded 92% conversion of FFAs to soy methyl esters after 1 hour of reaction. This study is exceptional because both the hydrolysis and the esterification use a simple reaction medium with high substrate concentrations.

Sign in / Sign up

Export Citation Format

Share Document