scholarly journals Biomechanical Considerations in the Design of High-Flexion Total Knee Replacements

2014 ◽  
Vol 2014 ◽  
pp. 1-6 ◽  
Author(s):  
Cheng-Kung Cheng ◽  
Colin J. McClean ◽  
Yu-Shu Lai ◽  
Wen-Chuan Chen ◽  
Chang-Hung Huang ◽  
...  
Keyword(s):  
Full Range ◽  
Computational Techniques ◽  
Knee Prostheses ◽  
Joint Function ◽  
High Flexion ◽  
Total Knee Replacements ◽  
Relieve Pain ◽  
Knee Replacements ◽  
Total Knee ◽  
Evaluation Techniques

Typically, joint arthroplasty is performed to relieve pain and improve functionality in a diseased or damaged joint. Total knee arthroplasty (TKA) involves replacing the entire knee joint, both femoral and tibial surfaces, with anatomically shaped artificial components in the hope of regaining normal joint function and permitting a full range of knee flexion. In spite of the design of the prosthesis itself, the degree of flexion attainable following TKA depends on a variety of factors, such as the joint’s preoperative condition/flexion, muscle strength, and surgical technique. High-flexion knee prostheses have been developed to accommodate movements that require greater flexion than typically achievable with conventional TKA; such high flexion is especially prevalent in Asian cultures. Recently, computational techniques have been widely used for evaluating the functionality of knee prostheses and for improving biomechanical performance. To offer a better understanding of the development and evaluation techniques currently available, this paper aims to review some of the latest trends in the simulation of high-flexion knee prostheses.

scholarly journals Roughness Digital Characterization and Influence on Wear of Retrieved Knee Components

2021 ◽  
Vol 11 (23) ◽  
pp. 11224
Author(s):  
Saverio Affatato ◽  
Alessandro Ruggiero ◽  
Silvia Logozzo ◽  
Maria Cristina Valigi
Keyword(s):  
Wear Behavior ◽  
Surface Characteristics ◽  
Lateral Part ◽  
Knee Prostheses ◽  
Total Knee Replacements ◽  
Knee Replacements ◽  
Total Knee ◽  
Digital Methods

Tribological performance of knee components are strongly related to the surface characteristics. Primarily, the roughness and its 3D distribution on the surfaces affect the joint performance. One of the main limitations related to the tribological study of knee prostheses is that most of the research studies report in vitro or in silico results, as knee retrievals are difficult to find or are too damaged to be analyzed. This paper is focused on the roughness characterization of retrieved metal femoral components of total knee replacements (TKR) by means of a rugosimeter and involving digital methods to reconstruct the 3D topography of the studied surfaces. The aim of this study is to investigate how changes and distribution of roughness are correlated between the medial vs. the lateral part and how the resulting digital topography can give insights about the wear behavior.

scholarly journals Towards the understanding of lubrication mechanisms in total knee replacements – Part I: Experimental investigations

2021 ◽  
Vol 156 ◽  
pp. 106874 ◽  
Author(s):  
David Nečas ◽  
Martin Vrbka ◽  
Max Marian ◽  
Benedict Rothammer ◽  
Stephan Tremmel ◽  
...  
Keyword(s):  
Experimental Investigations ◽  
Total Knee Replacements ◽  
Knee Replacements ◽  
Total Knee ◽  
Lubrication Mechanisms

scholarly journals Amorphous Carbon Coatings for Total Knee Replacements—Part I: Deposition, Cytocompatibility, Chemical and Mechanical Properties

Polymers ◽  
2021 ◽  
Vol 13 (12) ◽  
pp. 1952
Author(s):  
Benedict Rothammer ◽  
Kevin Neusser ◽  
Max Marian ◽  
Marcel Bartz ◽  
Sebastian Krauß ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Amorphous Carbon ◽  
Detailed Characterization ◽  
Carbon Coatings ◽  
Dlc Coatings ◽  
Total Knee Replacements ◽  
Knee Replacements ◽  
Total Knee ◽  
Amorphous Carbon Coatings

Diamond-like carbon (DLC) coatings have the potential to reduce implant wear and thus to contribute to avoiding premature failure and increase service life of total knee replacements (TKAs). This two-part study addresses the development of such coatings for ultrahigh molecular weight polyethylene (UHMWPE) tibial inlays as well as cobalt–chromium–molybdenum (CoCr) and titanium (Ti64) alloy femoral components. While a detailed characterization of the tribological behavior is the subject of part II, part I focusses on the deposition of pure (a‑C:H) and tungsten-doped hydrogen-containing amorphous carbon coatings (a‑C:H:W) and the detailed characterization of their chemical, cytological, mechanical and adhesion behavior. The coatings are fabricated by physical vapor deposition (PVD) and display typical DLC morphology and composition, as verified by focused ion beam scanning electron microscopy and Raman spectroscopy. Their roughness is higher than that of the plain substrates. Initial screening with contact angle and surface tension as well as in vitro testing by indirect and direct application indicate favorable cytocompatibility. The DLC coatings feature excellent mechanical properties with a substantial enhancement of indentation hardness and elastic modulus ratios. The adhesion of the coatings as determined in modified scratch tests can be considered as sufficient for the use in TKAs.

Sign in / Sign up

Export Citation Format

Share Document