scholarly journals Effects of Sulfurization Temperature on Properties of CZTS Films by Vacuum Evaporation and Sulfurization Method

2013 ◽  
Vol 2013 ◽  
pp. 1-6 ◽  
Author(s):  
Jie Zhang ◽  
Bo Long ◽  
Shuying Cheng ◽  
Weibo Zhang
Keyword(s):  
Thin Films ◽  
Solar Cells ◽  
Band Gap ◽  
Crystallite Size ◽  
Low Cost ◽  
Band Gap Energy ◽  
Vacuum Evaporation ◽  
Glass Substrates ◽  
Sulfurization Temperature ◽  
Czts Thin Films

Copper zinc tin sulfur (CZTS) thin films have been extensively studied in recent years for their advantages of low cost, high absorption coefficient (≥104 cm−1), appropriate band gap (~1.5 eV), and nontoxicity. CZTS thin films are promising materials of solar cells like copper indium gallium selenide (CIGS). In this work, CZTS thin films were prepared on glass substrates by vacuum evaporation and sulfurization method. Sn/Cu/ZnS (CZT) precursors were deposited by thermal evaporation and then sulfurized in N2+ H2S atmosphere at temperatures of 360–560°C to produce polycrystalline CZTS thin films. It is found that there are some impurity phases in the thin films with the sulfurization temperature less than 500°C, and the crystallite size of CZTS is quite small. With the further increase of the sulfurization temperature, the obtained thin films exhibit preferred (112) orientation with larger crystallite size and higher density. When the sulfurization temperature is 500°C, the band gap energy, resistivity, carrier concentration, and mobility of the CZTS thin films are 1.49 eV, 9.37 Ω · cm,1.714×1017 cm−3, and 3.89 cm2/(V · s), respectively. Therefore, the prepared CZTS thin films are suitable for absorbers of solar cells.

Fabrication and Photoelectrochemical Characterization of Fe, Co, Ni and Cu-Doped TiO2 Thin Films

2013 ◽  
Vol 764 ◽  
pp. 266-283 ◽  
Author(s):  
Ibram Ganesh ◽  
Rekha Dom ◽  
P.H. Borse ◽  
Ibram Annapoorna ◽  
G. Padmanabham ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Metal Ions ◽  
Band Gap ◽  
Metal Ion ◽  
Band Gap Energy ◽  
Chemical Compositions ◽  
Gap Energy ◽  
Glass Substrates ◽  
Photoelectrochemical Characterization

Different amounts of Fe, Co, Ni and Cu-doped TiO2 thin films were prepared on fluorine doped tin oxide (FTO) coated soda-lime glass substrates by following a conventional sol-gel dip-coating technique followed by heat treatment at 550 and 600°C for 30 min. These thin films were characterized for photo-current, chronoamperometry and band-gap energy values. The chemical compositions of metals-doped TiO2 thin films on FTO glass substrates were confirmed by XPS spectroscopic study. The metal-ions doped TiO2 thin films had a thickness of <200 nm="" optical="" transparency="" of="">80%, band-gap energy of >3.6 eV, and a direct band-to-band energy transition. The photoelectrochemical (PEC) studies revealed that all the metal-ions doped TiO2 thin films exhibit n-type semi-conducting behavior with a quite stable chronoamperometry and photo-currents that increase with the increase of applied voltage but decrease with the dopant metal-ion concentration in the thin film. Furthermore, these thin films exhibited flat-band potentials amenable to water oxidation reaction in a PEC cell. The 0.5 wt.% Cu-doped TiO2 thin film electrode exhibited an highest incident photon-to-current conversion efficiency (IPCE) of about 21%.

Preparation and characterization of V2O5 doped SiO2-TiO2 thin films

2012 ◽  
Vol 2 (1) ◽  
Author(s):  
Marek Nocuń ◽  
Sławomir Kwaśny
Keyword(s):  
Thin Films ◽  
Band Gap ◽  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Dip Coating ◽  
Band Gap Energy ◽  
Tio2 Thin Films ◽  
Glass Substrates ◽  
Gel Technique

AbstractIn our investigation, V doped SiO2/TiO2 thin films were prepared on glass substrates by dip coating sol-gel technique. Chemical composition of the samples was studied by X-ray photoelectron spectroscopy (XPS). Transmittance of the samples was characterized using UV-VIS spectrophotometry. Subsequently band-gap energy (Eg) was estimated for these films. Powders obtained from sols were characterized by FTIR spectroscopy. It was found that vanadium decreases optical band gap of SSiO2/TiO2 films.

Fabrication of low cost kesterite Cu2ZnSnS4(CZTS) thin films as counter-electrode for dye sensitised solar cells (DSSCs)

2015 ◽  
Vol 30 (5) ◽  
pp. 306-312 ◽  
Author(s):  
S. Chen ◽  
J. Tao ◽  
H. Tao ◽  
Y. Shen ◽  
L. Zhu ◽  
...  
Keyword(s):  
Thin Films ◽  
Solar Cells ◽  
Counter Electrode ◽  
Low Cost ◽  
Czts Thin Films

Cd-Free Zn(O,S) as Alternative Buffer Layer for Chalcogenide and Kesterite Based Thin Films Solar Cells: A Review

2020 ◽  
Vol 20 (6) ◽  
pp. 3622-3635 ◽  
Author(s):  
Kuldeep S. Gour ◽  
Rahul Parmar ◽  
Rahul Kumar ◽  
Vidya N. Singh
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Solar Cells ◽  
Band Gap ◽  
Buffer Layer ◽  
Low Cost ◽  
Incident Light ◽  
High Resistivity ◽  
Short Wavelength Range ◽  
Absorber Material

Cd is categorized as a toxic material with restricted use in electronics as there are inherent problems of treating waste and convincing consumers that it is properly sealed inside without any threat of precarious leaks. Apart from toxicity, band-gap of CdS is about 2.40–2.50 eV, which results significant photon loss in short-wavelength range which restricts the overall performance of solar cells. Thin film of Zn(O,S) is a favorable contender to substitute CdS thin film as buffer layer for CuInGaSe2 (CIGS), CuInGa(S,Se)2 (CIGSSe), Cu2ZnSn(S,Se)4 (CZTSSe) Cu2ZnSnSe4 (CZTSe), Cu2ZnSnS4 (CZTS) thin film absorber material based photovoltaic due to it made from earth abundant, low cost, non-toxic materials and its ability to improve the efficiency of chalcogenide and kesterite based photovoltaic due to wider band-gap which results in reduction of absorption loss compared to CdS. In this review, apart from mentioning various deposition technique for Zn(O,S) thin films, changes in various properties i.e., optical, morphological, and opto-electrical properties of Zn(O,S) thin film deposited using various methods utilized for fabricating solar cell based on CIGS, CIGSSe, CZTS, CZTSe and CZTSSe thin films, the material has been evaluated for all the properties of buffer layer (high transparency for incident light, good conduction band lineup with absorber material, low interface recombination, high resistivity and good device stability).

Properties of CdS Thin Films Grown by Chemical Bath Deposition as a Function of Bath Temperature

2009 ◽  
Vol 609 ◽  
pp. 243-247 ◽  
Author(s):  
H. Moualkia ◽  
S. Hariech ◽  
M.S. Aida
Keyword(s):  
Thin Films ◽  
Optical Properties ◽  
Band Gap ◽  
Chemical Bath Deposition ◽  
Bath Temperature ◽  
Band Gap Energy ◽  
X Ray Diffraction ◽  
Glass Substrates ◽  
Cds Thin Films ◽  
Direct Band

The present work deals with the preparation and characterization of cadmium sulfur (CdS) thin films. These films are prepared by chemical bath deposition on the well cleaned glass substrates. The thickness of the samples was measured by using profilometer DEKTAK, structural and optical properties were studied by X-ray diffraction analysis, and UV-visible spectrophotometry. The optical properties of the films have been investigated as a function of temperature. The band gap energy and Urbach energy were also investigated as a function of temperature. From the transmittance data analysis the direct band gap ranges from 2.21 eV to 2.34 eV. A dependence of band gap on temperature has been observed and the possible raisons are discussed. Transmission spectra indicates a high transmission coefficient (75 %). Structural analysis revealed that the films showed cubic structure, and the crystallite size decreased at a higher deposition temperature.

scholarly journals Optical Properties of Undoped and Indium-doped Tin Oxide Thin Films

2011 ◽  
Vol 35 (1) ◽  
pp. 99-111 ◽  
Author(s):  
Fatema Rezwana Chowdhury ◽  
Shamima Choudhury ◽  
Firoz Hasan ◽  
Tahmina Begum
Keyword(s):  
Thin Films ◽  
Band Gap ◽  
Tin Oxide ◽  
Optical Transmittance ◽  
Band Gap Energy ◽  
Visible Range ◽  
Absorption Region ◽  
Gap Energy ◽  
Glass Substrates ◽  
In Doping

Thin films of Tin Oxide (SnO2), having thickness of 200 nm, were formed on to glass substrates by thermal evaporation of high-purity SnO2 powder in vacuum at various substrate temperatures (TS), ranging between 25 and 200°C. SnO2 films with varying thickness were also prepared for a fixed TS = 100°C. Further, doping of SnO2 films with Indium (In) was accomplished through solid state diffusion process by successive deposition of SnO2 and In films and subsequent annealing at 200°C for 10 minutes. Both undoped and doped films were characterized optically by UV-VIS-NIR spectrophotometry in the photon wavelength ranging from 300 to 2500 nm. In the visible photon wavelength range, the average optical transmittance (T%) of the films with varying TS was found to be 85%. The maximum value of T % was found to be 89 % around the wavelength of 700nm. The variation of absorption coefficient with photon energy in the fundamental absorption region is the steepest for TS = 100°C. The sub-band gap (SBG) absorption is also minimum for this Ts. A fluctuating behavior of the band gap energy (Eg) with Ts is observed attaining the highest value of 3.59 eV for Ts = 100°C. The band gap energy increases with thickness but T% in the visible range decreases. The T% in the visible range varies inversely with indium doping, being highest for undoped films. The Eg increases upto 2 wt% In doping and gradually decreases for enhanced doping. It seems reasonable to conclude that In doping does not bring favorable optical characteristics. Undoped SnO2 films having thickness of 200 nm and formed at substrate temperature of 100°C yield essential acceptable properties for photovoltaic applications.DOI: http://dx.doi.org/10.3329/jbas.v35i1.7975Journal of Bangladesh Academy of Sciences, Vol.35, No.1, 99-111, 2011

Preparation of CuIn(SxSe1–x)2 thin films with tunable band gap by controlling sulfurization temperature of CuInSe2

2010 ◽  
Vol 25 (12) ◽  
pp. 2426-2429 ◽  
Author(s):  
Guangjun Wang ◽  
Gang Cheng ◽  
Binbin Hu ◽  
Xiaoli Wang ◽  
Shaoming Wan ◽  
...  
Keyword(s):  
Thin Films ◽  
Solar Cell ◽  
Band Gap ◽  
Low Cost ◽  
Chalcopyrite Structure ◽  
X Ray Diffraction ◽  
Large Area ◽  
X Ray ◽  
Sulfurization Temperature ◽  
Tunable Band Gap

In this paper, polycrystalline CuIn(SxSe1–x)2 thin films with tunable x and Eg (band gap) values were prepared by controlling the sulfurization temperature (T) of CuInSe2 thin films. X-ray diffraction indicated the CuIn(SxSe1–x)2 films exhibited a homogeneous chalcopyrite structure. When T increases from 150 to 500 °C, x increases from 0 to 1, and Eg increases from 0.96 to 1.43 eV. The relations between x and Eg and the sulfurization process of CuIn(SxSe1–x)2 thin films have been discussed. This work provides an easy and low-cost technique for preparing large area absorber layers of solar cell with tunable Eg.

Effect of Tin Composition on Cu2ZnSnS4 Photovoltaic Absorbers

2012 ◽  
Vol 534 ◽  
pp. 156-159 ◽  
Author(s):  
Dong Hua Fan ◽  
Rong Zhang ◽  
Hui Ren Peng
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Band Gap ◽  
Crystallite Size ◽  
Optical Band Gap ◽  
Diffraction Peak ◽  
X Ray Diffraction ◽  
X Ray ◽  
Poor Condition ◽  
Czts Thin Films

Cu2ZnSnS4 (CZTS) thin films are prepared by sulfurizing the precursors deposited by vacuum evaporation methods. The samples sulfurized at 500°C for 3h shows the strong (112) diffraction peak at 28.45˚, suggesting the successful synthesis of CZTS thin films. The X-ray diffraction shows that CZTS thin film prepared in Sn-poor condition have the best crystallinity. The Sn-dependent crystallite size was calculated to be 19.53-21.03 nm. In addition, we found that the optical band gap with various Sn contents can be modulated at 1.48-1.85 eV

Effect of Crystallite Size on the Optical and Structural Properties of Gadolinium-Doped Zinc Oxide

2016 ◽  
Vol 1133 ◽  
pp. 414-418 ◽  
Author(s):  
Nurul Fadzilah Ab Rasid ◽  
Siti Nooraya Mohd Tawil ◽  
Norhidayah Che Ani ◽  
Mohd Zainizan Sahdan
Keyword(s):  
Thin Films ◽  
Crystallite Size ◽  
Diluted Magnetic Semiconductor ◽  
Sol Gel ◽  
Magnetic Semiconductor ◽  
Band Gap Energy ◽  
Optical Investigation ◽  
Glass Substrates ◽  
Coating Method ◽  
Diluted Magnetic

Rare earth Gd-doped ZnO thin films were prepared by a simple sol-gel spin coating method in order to search for a new functional diluted magnetic semiconductor for potential application in spintronics. The thin films were deposited onto glass substrates with zinc acetate dehydrate, monoethanolamine and 2-methoxyethanol as a starting material, stabilizer and solvent, respectively. The dopant percentage was increased up to 8%. Optical investigation showed that the crystallinity of the thin films was changing due to the increase of the Gd concentrations and optical band gap energy (Eg) value was estimated to be around 3.12 ~ 3.28 eV using Tauc's model. The crystallite size determined from XRD spectra and the results was found that the value is in the range of 14.42 ~ 21.98 nm.

Characterization of MnS Thin Films Deposited by Chemical Bath Deposition

2019 ◽  
Vol 969 ◽  
pp. 433-438 ◽  
Author(s):  
Dattatraya K. Sonavane ◽  
S.K. Jare ◽  
M.A. Shaikh ◽  
R.V. Kathare ◽  
R.N. Bulakhe
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Band Gap ◽  
Chemical Bath Deposition ◽  
Band Gap Energy ◽  
Sulfur Source ◽  
X Ray Diffraction ◽  
Glass Substrates ◽  
Double Beam

Glass substrates are used to deposit thin films utilizing basic and value effective chemical bath deposition (CBD) technique. The films were prepared from the mixture as solutions of manganous acetate tetrahydrate [C4H6MnO44H2O] as a manganese source, thiourea [(H2 N) 2 CS] as a sulfur source and triethanolamine (TEA) [(HOC2H4)3N] as a complexing agent.In the present paper the deposition was successfully done at 60 °C temperature. The absorption properties and band gap energy were determined employing double beam spectrophotometer. The optical band gap value calculated from absorption spectra of MnS thin film is found to be about 3.1eV.The MnS thin film was structurally characterized by X-ray Diffraction (XRD). The MnS thin film was morphologically characterized by Scanning Electron Microscopy (SEM) and elemental analysis was performed using EDS to confirm the formation of MnS.

Sign in / Sign up

Export Citation Format

Share Document