scholarly journals Modeling and Simulation of Turbulent Flows through a Solar Air Heater Having Square-Sectioned Transverse Rib Roughness on the Absorber Plate

2013 ◽  
Vol 2013 ◽  
pp. 1-12 ◽  
Author(s):  
Anil Singh Yadav ◽  
J. L. Bhagoria
Keyword(s):  
Heat Transfer ◽  
Turbulent Flows ◽  
Convective Heat Transfer Coefficient ◽  
Performance Parameter ◽  
Roughness Height ◽  
Solar Air Heater ◽  
Absorber Plate ◽  
Air Heater ◽  
Relative Roughness ◽  
Flow Through

Solar air heater is a type of heat exchanger which transforms solar radiation into heat energy. The thermal performance of conventional solar air heater has been found to be poor because of the low convective heat transfer coefficient from the absorber plate to the air. Use of artificial roughness on a surface is an effective technique to enhance the rate of heat transfer. A CFD-based investigation of turbulent flow through a solar air heater roughened with square-sectioned transverse rib roughness has been performed. Three different values of rib-pitch (P) and rib-height (e) have been taken such that the relative roughness pitch (P/e=14.29) remains constant. The relative roughness height,e/D, varies from 0.021 to 0.06, and the Reynolds number, Re, varies from 3800 to 18,000. The results predicted by CFD show that the average heat transfer, average flow friction, and thermohydraulic performance parameter are strongly dependent on the relative roughness height. A maximum value of thermohydraulic performance parameter has been found to be 1.8 for the range of parameters investigated. Comparisons with previously published work have been performed and found to be in excellent agreement.

scholarly journals Thermal Performance of Three Sided Artificially Roughened Double Duct Parallel Flow Solar Air Heater

2018 ◽  
Vol 7 (1) ◽  
pp. 5-15
Author(s):  
Chander Kant ◽  
Prashant Kumar ◽  
Ankur Gill ◽  
Dhiraj Parkash Dhiman
Keyword(s):  
Heat Transfer ◽  
Reynold Number ◽  
Parallel Flow ◽  
Working Fluid ◽  
Solar Air Heater ◽  
Absorber Plate ◽  
Navier Stokes Equation ◽  
Ansys Fluent ◽  
Air Heater ◽  
Relative Roughness

A solar air heater is basically a heat exchanger, which intercepts the incident solar radiation, converts it into heat and finally transfers this heat to a working fluid for an end use system. The mode of air flowing in the ducts of a solar air heater is one of the most significant aspects concerned with solar air heater which dominantly affect. A double duct parallel flow artificially roughened solar air heater with three sides of the absorber plate is investigated in the current study. Unlike the conventional model of solar air heater with only one sided roughened absorber plate, a novel solar air heater with three artificially roughened absorber plate is used so that the surface area of the absorber plate is increased which ultimately increases the rate of heat transfer. Additionally, a double duct parallel flow arrangement through inner and outer duct of solar air heater is considered order to enhance the heat transfer rate. A numerical investigation of the heat transfer and friction factor characteristics of a double duct parallel flow three sided artificially roughened solar air heater has been carried out. A commercial finite volume CFD code ANSYS FLUENT is used to simulate turbulent air flow through artificial roughened solar air heater. Governing equations of the fluid flow and heat transfer i.e. Navier-Stokes equation and energy equation are solved with RNG k-ε turbulence model. Nine different configuration of square rib are studied with relative roughness pitch (P/e = 5-10) and relative roughness height (e/D = 0.03-0.06). The Reynold number of the flow is varied from 2500 to 16000.

Experimental Investigation on Thermal Performance in Three-Sided Solar Air Heaters Having an Alignment of Multi-v and Transverse Wire Roughness on the Absorber Plate

2020 ◽  
Vol 142 (5) ◽  
Author(s):  
Dhananjay Kumar ◽  
Laljee Prasad
Keyword(s):  
Thermal Performance ◽  
Thermal Efficiency ◽  
Roughness Height ◽  
Space Heating ◽  
Solar Air Heater ◽  
Artificial Roughness ◽  
Absorber Plate ◽  
Air Heater ◽  
Relative Roughness ◽  
Operational Constraints

Abstract The use of artificial roughness is an efficient and commercial way to appreciate the thermal performance from the collector to the air in solar air heater ducts, for numerous applications such as space-heating, crop-drying, and seasoning of timber industrial purpose. In this paper, the tentative inquiry on thermal enactment using new-fangled of three-sided roughened quadrilateral duct solar air heater having an alignment of multiple-v and transverse wire is performed and compared the outcomes with smooth duct air heater under similar operational circumstances. The modification of an arrangement and operational constraints is inspected within the restrictions, the moral of four-sided duct aspect ratio (W/H) = 8, the Reynolds number occupied from 3000 to 12,000, fraction of pitch to roughness height, P/e in the range of 10–25; ratio of roughness height to hydraulic diameter, e/D in the range of 0.018–0.042; at flow attack angle, α = 60 deg for constant moral of relative roughness width, (W/w) = 6. The augmentation on thermal efficiency in three-sided rugged duct is found to be 23–86% when compared to smooth duct, and the maximum thermal efficiency can occur at P/e = 10 and e/D = 0.042. The enhancement in air temperature flowing under three-sided roughened duct is found to be 49.27% more than that of a smooth duct. The instant innovative form of three-sided roughened solar air warmer would be preferable to those of a smooth solar air heater with respect to heat assignment.

Thermal–hydraulic analysis of a solar air heater fitted with a wire-roughened absorber plate

2021 ◽  
pp. 095440892110590
Author(s):  
Nanjundappa Madhukeshwara ◽  
A Alhadhrami ◽  
Hassan A H Alzahrani ◽  
B H Prasanna
Keyword(s):  
Heat Transfer ◽  
Friction Factor ◽  
Efficiency Index ◽  
Hydraulic Performance ◽  
Index Formula ◽  
Solar Air Heater ◽  
Absorber Plate ◽  
Air Heater ◽  
Relative Roughness ◽  
Nusselt Numbers

This study is to evaluate heat transmission and friction in a rectangular solar air heater with a V-shaped wire rib roughness on the absorber plate that operates in fully formed turbulent flow. Additionally, studies are performed to generate prediction equations for the average friction factor, Stanton number, and efficiency index. The Reynolds number [Formula: see text]–[Formula: see text], angle of attack [Formula: see text]20[Formula: see text]–90[Formula: see text]), relative roughness pitch [Formula: see text]–[Formula: see text], relative roughness height [Formula: see text]–[Formula: see text], and the aspect ratio [Formula: see text]–[Formula: see text] was varied. The efficiency index [Formula: see text] is commonly employed as a thermo-hydraulic performance metric. It is computed as [Formula: see text]. The wire roughness and airflow parameters [Formula: see text] are optimized to maximize heat transfer while retaining minimal friction losses. On the basis of resemblance criteria, average Stanton numbers, average Nusselt numbers, and even average friction factors are derived. The results are compared to those obtained with a smooth absorber duct under similar airflow circumstances in order to assess the increase in heat transfer coefficient and friction factor. The [Formula: see text], and [Formula: see text] have a significant influence on thermo–hydraulic performance, according to these studies. With [Formula: see text], [Formula: see text], [Formula: see text], and [Formula: see text], the optimal configuration geometry for wire roughness and solar air heater duct is identified.

scholarly journals CFD Analysis to Study Effect of Circular Vortex Generator Placed in Inlet Section to Investigate Heat Transfer Aspects of Solar Air Heater

2014 ◽  
Vol 2014 ◽  
pp. 1-11 ◽  
Author(s):  
Vipin B. Gawande ◽  
A. S. Dhoble ◽  
D. B. Zodpe
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Friction Factor ◽  
Vortex Generator ◽  
Inlet Section ◽  
Solar Air Heater ◽  
Cfd Analysis ◽  
Absorber Plate ◽  
Air Heater ◽  
Relative Roughness

CFD analysis of 2-dimensional artificially roughened solar air heater duct with additional circular vortex generator, inserted in inlet section is carried out. Circular transverse ribs on the absorber plate are placed as usual. The analysis is done to investigate the effect of inserting additional vortex generator on the heat transfer and flow friction characteristics inside the solar air heater duct. This investigation covers relative roughness pitch in the range of 10 ≤P/e≤ 25 and relevant Reynolds numbers in the range of 3800 ≤ Re ≤ 18000. Relative roughness height (e/D) is kept constant as 0.03 for analysis. The turbulence created due to additional circular vortex generator increases the heat transfer rate and at the same time there is also increase in friction factor values. For combined arrangement of ribs and vortex generator, maximum Nusselt number is found to be 2.05 times that of the smooth duct. The enhancement in Nusselt number with ribs and additional vortex generator is found to be 1.06 times that of duct using ribs alone. The maximum increase in friction factor with ribs and circular vortex generator is found to be 2.91 times that of the smooth duct. Friction factor in a combined arrangement is 1.114 times that in a duct with ribs alone on the absorber plate. The augmentation in Thermal Enhancement Factor (TEF) with vortex generator in inlet section is found to be 1.06 times more than with circular ribs alone on the absorber plate.

scholarly journals THERMOHYDRAULIC PERFORMANCE OF AN EQUILATERAL TRIANGULAR DUCT WITH ARTIFICIAL ROUGHNESS USED IN SOLAR AIR HEATER

2013 ◽  
pp. 46-51
Author(s):  
GAURAV BHARADWAJ ◽  
VARUN VARUN ◽  
AVDHESH SHARMA
Keyword(s):  
Reynolds Number ◽  
Aspect Ratio ◽  
Angle Of Attack ◽  
Roughness Height ◽  
Solar Air Heater ◽  
Artificial Roughness ◽  
Absorber Plate ◽  
Air Heater ◽  
Relative Roughness

The thermohydraulic performance of artificially roughened equilateral triangular solar air heater duct has been investigated and the comparision of the same has been presented with that of a conventional smooth solar air heater duct. The range of relative roughness height (e/Dh) is from 0.021 to 0.043, value of angle of attack (α) and relative roughness pitch (p/e) has been 30° and 8 respectively. The range of Reynolds number is from 5600 to 28000 and aspect ratio of the duct is 1.15. It has been found that the thermohydraulic performance of artificially roughened triangular solar air heater duct is always more than that of the smooth absorber plate in the range of Reynolds number investigated.

scholarly journals NUMERICAL ANALYSIS FOR NUSSELT NUMBER AND HEAT TRANSFER AUGMENTATION ON SOLAR AIR HEATER ROUGHENED WITH SQUARE RIB ROUGHNESS ON THE ABSORBER PLATE

2019 ◽  
Vol 13 (1) ◽  
Author(s):  
Amit Kumar ◽  
Apurba Layek
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Numerical Study ◽  
Energy Gain ◽  
Solar Air Heater ◽  
Absorber Plate ◽  
Gain Ratio ◽  
Air Heater ◽  
Heat Transfer Augmentation ◽  
Relative Roughness

Heat transfer rate on solar air heater system is generally achieved by suitable modification of absorber plate surface with acceptable geometry of rib roughness. In this paper a numerical study is performed using CFD based computational analysis of heat transfer augmentation equipped with the square rib roughness created artificially on the absorber plate. The 2D analysis is performed using ANSYS 16.2 Code with RNG k-ε turbulence model to investigate the heat transfer and fluid flow characteristics. The augmentation of heat transfer on increase of Reynolds number enhance the Nusselt number which is referred as energy gain ratio with the use of rib roughness was examined and their relative evaluation has been plotted. The parameter which is considered for the range of analysis is taken as relative roughness pitch (P/e), relative roughness height (e/D) and the Reynolds numbers (Re) ranging from 3800-18000. The enhancement of heat transfers due to rib roughness on the absorber plate have been compared with those for smooth ducts for the same flow and thermal boundary condition to determine the energy gain ratio of solar air heater. The result obtained by the present investigation shows that the maximum value of energy gain ratio is found to be about 1.93 times the smooth duct for the studied range of parameters.

Impact of relative roughness height on the materialistic thermohydraulic performance of the multiple V-ribbed solar air heater

2020 ◽  
Vol 26 ◽  
pp. 1845-1849
Author(s):  
Gagan Bansal ◽  
Chandra Kishore ◽  
Vaishally Dogra ◽  
Amit Bansal ◽  
Rahul Keshari
Keyword(s):  
Roughness Height ◽  
Solar Air Heater ◽  
Air Heater ◽  
Relative Roughness
Sign in / Sign up

Export Citation Format

Share Document