scholarly journals Numerical Simulation of Airfoil Aerodynamic Penalties and Mechanisms in Heavy Rain

2013 ◽  
Vol 2013 ◽  
pp. 1-13 ◽  
Author(s):  
Zhenlong Wu ◽  
Yihua Cao ◽  
M. Ismail
Keyword(s):  
Boundary Layer ◽  
Water Film ◽  
Leading Edge ◽  
Heavy Rain ◽  
Mathematic Model ◽  
Boundary Layer Separation ◽  
Boundary Layer Transition ◽  
Percentage Increase ◽  
Layer Transition ◽  
Maximum Percentage

Numerical simulations that are conducted on a transport-type airfoil, NACA 64-210, at a Reynolds number of2.6×106and LWC of 25 g/m3explore the aerodynamic penalties and mechanisms that affect airfoil performance in heavy rain conditions. Our simulation results agree well with the experimental data and show significant aerodynamic penalties for the airfoil in heavy rain. The maximum percentage decrease inCLis reached by 13.2% and the maximum percentage increase inCDby 47.6%. Performance degradation in heavy rain at low angles of attack is emulated by an originally creative boundary-layer-tripped technique near the leading edge. Numerical flow visualization technique is used to show premature boundary-layer separation at high angles of attack and the particulate trajectories at various angles of attack. A mathematic model is established to qualitatively study the water film effect on the airfoil geometric changes. All above efforts indicate that two primary mechanisms are accountable for the airfoil aerodynamic penalties. One is to cause premature boundary-layer transition at low AOA and separation at high AOA. The other occurs at times scales consistent with the water film layer, which is thought to alter the airfoil geometry and increase the mass effectively.

CFD Prediction of Boundary Layer Transition and Separation on an Airfoil at Varying Angle of Attack

2007 ◽  
Author(s):  
Nicole M. Wolgemuth ◽  
D. Keith Walters
Keyword(s):  
Boundary Layer ◽  
Separation Bubble ◽  
Turbulence Models ◽  
Leading Edge ◽  
Boundary Layer Separation ◽  
Boundary Layer Transition ◽  
Suction Surface ◽  
Layer Transition ◽  
Turbulent Airflow ◽  
Naca 0012

This study analyzes the predicted flow over a NACA 0012 airfoil at varying angles of attack and three different Reynolds numbers. The ability of three different turbulence models to predict boundary layer separation and transition behavior is investigated. Particular interest is paid to prediction of the separation bubble that develops near the leading edge of the airfoil suction surface prior to stall. The FLUENT CFD solver was used to simulate turbulent airflow over the airfoil. The three turbulence models include the standard and realizable forms of the k-ε model, available in FLUENT, as well as a recently developed transition-sensitive k-ω model that was implemented into the solver using user-defined functions. By employing the new, transition-sensitive model, computed properties of the flow field were found to be closer to experimental data than results produced by utilizing built-in turbulence models. Most importantly, the new, transition-sensitive model predicts the occurrence of the separation bubble, which the other models are unable to predict. The new model also clearly reproduces the laminar, transitional, and turbulent flow that occurs over the airfoil.

Aerodynamic study of aerofoil and wing in simulated rain environment via a two-way coupled Eulerian-Lagrangian approach

2014 ◽  
Vol 118 (1204) ◽  
pp. 643-668 ◽  
Author(s):  
Z. Wu ◽  
Y. Cao
Keyword(s):  
Boundary Layer ◽  
Three Dimensional ◽  
Water Film ◽  
Heavy Rain ◽  
Aerodynamic Performance ◽  
Lagrangian Approach ◽  
Boundary Layer Transition ◽  
Wing Surface ◽  
Layer Transition ◽  
Stall Angle

Abstract Aerodynamic performance degradation has been considered a critical hazard to aircraft due to flying in heavy rain. In this work, a two-way momentum coupled Eulerian-Lagrangian approach is developed to study the aerodynamic performance of a two-dimensional (2D) transport-type NACA 64-210 cruise and landing configuration aerofoil as well as a three-dimensional (3D) NACA 64-210 cruise configuration rectangular wing in heavy rain environment. Raindrop impacts, splashback and formed water film are modeled. The steady-state incompressible air flow field and the raindrop trajectory are calculated alternately by incorporating an interphase momentum coupling term through a curvilinear body-fitted grid surrounding the aerofoil/wing. Our simulation results agree well with the experimental results and show significant aerodynamic penalties for all the test cases in heavy rain. Rain-induced premature boundary-layer transition and separation are observed and details of the raindrop splashback effect on the boundary layer are examined. A 1° rain-induced decrease in stall angle-of-attack is predicted. An uneven water film upon the wing surface is observed and its effect on the wing surface roughness is also examined.

scholarly journals Compressible Direct Numerical Simulation of Low-Pressure Turbines: Part I — Methodology

2014 ◽  
Author(s):  
Richard D. Sandberg ◽  
Richard Pichler ◽  
Liwei Chen ◽  
Roderick Johnstone ◽  
Vittorio Michelassi
Keyword(s):  
Numerical Simulation ◽  
Boundary Layer ◽  
Direct Numerical Simulation ◽  
Environmental Parameters ◽  
Boundary Layer Separation ◽  
Low Pressure ◽  
Boundary Layer Transition ◽  
Layer Transition ◽  
Laminar Separation ◽  
Background Turbulence

Modern low pressure turbines (LPT) feature high pressure ratios and moderate Mach and Reynolds numbers, increasing the possibility of laminar boundary-layer separation on the blades. Upstream disturbances including background turbulence and incoming wakes have a profound effect on the behavior of separation bubbles and the type/location of laminar-turbulent transition and therefore need to be considered in LPT design. URANS are often found inadequate to resolve the complex wake dynamics and impact of these environmental parameters on the boundary layers and may not drive the design to the best aerodynamic efficiency. LES can partly improve the accuracy, but has difficulties in predicting boundary layer transition and capturing the delay of laminar separation with varying inlet turbulence levels. Direct Numerical Simulation (DNS) is able to overcome these limitations but has to date been considered too computationally expensive. Here a novel compressible DNS code is presented and validated, promising to make DNS practical for LPT studies. Also, the sensitivity of wake loss coefficient with respect to freestream turbulence levels below 1% is discussed.

Keel Design for Low Viscous Drag

1987 ◽  
Author(s):  
Clifford J. Obara ◽  
C. P. van Dam
Keyword(s):  
Boundary Layer ◽  
Laminar Flow ◽  
Laminar Boundary Layer ◽  
Leading Edge ◽  
Boundary Layer Transition ◽  
Viscous Drag ◽  
Hydrodynamic Characteristics ◽  
Sweep Angle ◽  
Layer Transition ◽  
Layer Flow

In this paper, foil and planform parameters which govern the level of viscous drag produced by the keel of a sailing yacht are discussed. It is shown that the application of laminar boundary-Layer flow offers great potential for increased boat speed resulting from the reduction in viscous drag. Three foil shapes have been designed and it is shown that their hydro­dynamic characteristics are very much dependent on location and mode of boundary-Layer transition. The planform parameter which strongly affects the capabilities of the keel to achieve laminar flow is lea ding-edge sweep angle. The two significant phenomena related to keel sweep angle which can cause premature transition of the laminar boundary layer are crossflow instability and turbulent contamination of the leading-edge attachment line. These flow phenomena and methods to control them are discussed in detail. The remaining factors that affect the maintainability of laminar flow include surface roughness, surface waviness, and freestream turbulence. Recommended limits for these factors are given to insure achievability of laminar flow on the keel. In addition, the application of a simple trailing-edge flap to improve the hydrodynamic characteristics of a foil at moderate-to-high leeway angles is studied.

Numerical Study of Wall Influence on Boundary-Layer Transition for Two-Dimensional NACA 16-012 and 4412 Hydrofoil Sections

1990 ◽  
Vol 34 (01) ◽  
pp. 38-47
Author(s):  
R. Latorre ◽  
R. Baubeau
Keyword(s):  
Boundary Layer ◽  
Test Section ◽  
Numerical Study ◽  
Suction Side ◽  
Boundary Layer Separation ◽  
Boundary Layer Transition ◽  
Layer Transition ◽  
Turbulent Separation ◽  
Side Pressure ◽  
Effective Angle

One of the difficulties in hydrofoil model tests is the relatively low Reynolds number of the test piece and the presence of the test section walls. This paper presents the results of systematic calculations of the potential flow field of NA 4412 and NACA 16-012 hydrofoil in a test section with wall-to-chord ratios h/c -1.0. The corresponding boundary-layer calculations using the CERT calculation scheme are presented to show the influence of the nearby walls on shifting the location of the boundary-layer laminar-turbulent separation as well as turbulent separation. By introducing an effective angle of attack, it is possible to obtain close agreement in the calculated and measured suction side pressure distortion as well as the locations of the boundary-layer separation and transition.

Effects of Weak Free Stream Nonuniformity on Boundary Layer Transition (Keynote Paper)

2003 ◽  
Author(s):  
Jonathan H. Watmuff
Keyword(s):  
Boundary Layer ◽  
Free Stream ◽  
Leading Edge ◽  
Boundary Layer Transition ◽  
Mean Flow ◽  
Layer Transition ◽  
Free Stream Turbulence ◽  
Tollmien Schlichting ◽  
Distorted Waves ◽  
Thickness Variations

Experiments are described in which well-defined FSN (Free Stream Nonuniformity) distributions are introduced by placing fine wires upstream of the leading edge of a flat plate. Large amplitude spanwise thickness variations are present in the downstream boundary layer resulting from the interaction of the laminar wakes with the leading edge. Regions of elevated background unsteadiness appear on either side of the peak layer thickness, which share many of the characteristics of Klebanoff modes, observed at elevated Free Stream Turbulence (FST) levels. However, for the low background disturbance level of the free stream, the layer remains laminar to the end of the test section (Rx ≈ l.4×106) and there is no evidence of bursting or other phenomena associated with breakdown to turbulence. A vibrating ribbon apparatus is used to demonstrate that the deformation of the mean flow is responsible for substantial phase and amplitude distortion of Tollmien-Schlichting (TS) waves. Pseudo-flow visualization of hot-wire data shows that the breakdown of the distorted waves is more complex and occurs at a lower Reynolds number than the breakdown of the K-type secondary instability observed when the FSN is not present.

Criteria for Boundary Layer Transition

2011 ◽  
Author(s):  
Stefan Becker ◽  
Donald M. McEligot ◽  
Edmond Walsh ◽  
Eckart Laurien
Keyword(s):  
Boundary Layer ◽  
Boundary Layers ◽  
Boundary Layer Flow ◽  
Leading Edge ◽  
Boundary Layer Transition ◽  
Turbulence Level ◽  
Two Dimensional ◽  
Freestream Turbulence ◽  
Layer Transition ◽  
Layer Flow

New results are deduced to assess the validity of proposed transition indicators when applied to situations other than boundary layers on smooth surfaces. The geometry employed utilizes a two-dimensional square rib to disrupt the boundary layer flow. The objective is to determine whether some available criteria are consistent with the present measurements of laminar recovery and transition for the flow downstream of this rib. For the present data — the proposed values of thresholds for transition in existing literature that are based on the freestream turbulence level at the leading edge are not reached in the recovering laminar run but they are not exceeded in the transitioning run either. Of the pointwise proposals examined, values of the suggested quantity were consistent for three of the criteria; that is, they were less than the threshold in laminar recovery and greater than it in the transitioning case.

Effect of Leading Edge Geometry on Boundary Layer Transition-An Experimental Approach

2014 ◽  
Vol 590 ◽  
pp. 53-57 ◽  
Author(s):  
Dinesh Bhatia ◽  
Guang Jun Yang ◽  
Jing Sun ◽  
Jian Wang
Keyword(s):  
Boundary Layer ◽  
Flat Plate ◽  
Boundary Layer Thickness ◽  
Experimental Approach ◽  
Flow Characteristics ◽  
Leading Edge ◽  
Boundary Layer Transition ◽  
Layer Transition ◽  
Edge Geometry ◽  
Displacement Thickness

Boundary layers are affected by a number of different factors. Transition of the boundary layer is very sensitive to changes in geometry, velocity and turbulence levels. An understanding of the flow characteristics over a flat plate subjected to changes in geometry, velocity and turbulence is essential to try and understand boundary layer transition. Experiments were conducted in Low Turbulence wind tunnel (LTWT) at Northwestern Polytechnical University (NWPU), China to understand the effects due to changes in geometric profiles on boundary layer transition. The leading edge of the flat plate was changed and several different configurations ranging from Aspect Ratio (AR) 1 to 12 were used. Turbulence level was kept constant at 0.02% and the velocity was kept at default value of 30 m/s. The results indicated that as the AR increases, boundary layer thickness reduces at the same location along the plate. The displacement thickness shows that the fluctuations increase with an increase with AR which denotes the effect of leading edge on turbulence spot’s production. For AR≥4, an increase in AR led to an elongation of the transition zone and a delay in transition onset. Nomenclature

Keel Design for Low Viscous Drag

1989 ◽  
Vol 33 (02) ◽  
pp. 145-155
Author(s):  
Clifford J. Obara ◽  
C. P. van Dam
Keyword(s):  
Boundary Layer ◽  
Laminar Flow ◽  
Laminar Boundary Layer ◽  
Leading Edge ◽  
Boundary Layer Transition ◽  
Viscous Drag ◽  
Hydrodynamic Characteristics ◽  
Sweep Angle ◽  
Layer Transition ◽  
Layer Flow

Foil and planform parameters which govern the level of viscous drag produced by the keel of a sailing yacht are discussed. It is shown that the application of laminar boundary-layer flow offers great potential for increased boat speed resulting from the reduction in viscous drag. Three foil shapes have been designed and it is shown that their hydrodynamic characteristics are very much dependent on location and mode of boundary-layer transition. The planform parameter which strongly affects the capabilities of the keel to achieve laminar flow is leading-edge sweep angle. The two significant phenomena related to keel sweep angle which can cause premature transition of the laminar boundary layer are crossflow instability and turbulent contamination of the leading-edge attachment line. These flow phenomena and methods to control them are discussed in detail. The remaining factors that affect the maintainability of laminar flow include surface roughness, surface waviness, and freestream turbulence. Recommended limits for these factors are given to insure achievability of laminar flow on the keel. In addition, the application of a simple trailing-edge flap to improve the hydrodynamic characteristics of a foil at moderate-to-high leeway angles is studied.

Sign in / Sign up

Export Citation Format

Share Document