scholarly journals Analysis of Liquid Zone Control Valve Oscillation Problem in CANDU Reactors

2013 ◽  
Vol 2013 ◽  
pp. 1-12
Author(s):  
Elnara Nasimi ◽  
Hossam A. Gabbar
Keyword(s):  
Steady State ◽  
Nuclear Power ◽  
Control Valve ◽  
Liquid Zone ◽  
Candu Reactors ◽  
Zone Control ◽  
Power Adjustment ◽  
Oscillation Problem ◽  
Made In

This paper looks at the existing challenges with steady-state Liquid Zone control at some CANDU (CANada Deuterium Uranium) stations, where—contrary to expectations for equilibrium flow—Liquid Zone Control Valve oscillations have proven to be a chronic, unanticipated challenge. Currently, the exact causes of this behaviour are not fully understood, although it is confirmed that the Control Valve oscillations are not due to automatic power adjustment requests or zone level changes due to process leaks. This phenomenon was analysed based on a case study of one domestic nuclear power station to determine whether it could be attributed to inherent controller properties. Next, a proposal is made in an attempt to improve current performance with minimal changes to the existing system hardware and logic using conventional technologies. Finally, a proposal was made to consider Model Predictive Control-based technology to minimize the undesirable Control Valve oscillations at steady state based on the obtained simulation results and discussion of other available alternatives.

scholarly journals Improvements in Incinerators by Means of Gas Turbine Based Cogen Systems

1990 ◽  
Author(s):  
Ir. Ted Wiekmeijer
Keyword(s):  
Gas Turbine ◽  
Nuclear Power ◽  
Waste Heat ◽  
Waste Incineration ◽  
Global Risk ◽  
Waste Heat Boiler ◽  
Power Stations ◽  
New Process ◽  
Made In

In this paper a new process is described to improve the efficiency of power generation in waste incineration plants. It is proposed to superheat the steam in a gas turbine/waste heat boiler combination rather than in the incinerator boiler. Although this is not discussed in this paper the same process may be applied in nuclear power stations where the superheating of steam is also a problem. A global risk-analysis of the addition of equipment is made in this paper. On basis of a case-study the financial advantages are demonstrated.

Validation of On-line Respiration Meter and its Applications by Computer Simulation

1992 ◽  
Vol 26 (5-6) ◽  
pp. 1355-1363 ◽  
Author(s):  
C-W. Kim ◽  
H. Spanjers ◽  
A. Klapwijk
Keyword(s):  
Steady State ◽  
Activated Sludge ◽  
Respiration Rate ◽  
Oxygen Demand ◽  
Operating Conditions ◽  
Mass Balances ◽  
Short Term ◽  
Respiration Rates ◽  
On Line ◽  
Made In

An on-line respiration meter is presented to monitor three types of respiration rates of activated sludge and to calculate effluent and influent short term biochemical oxygen demand (BODst) in the continuous activated sludge process. This work is to verify if the calculated BODst is reliable and the assumptions made in the course of developing the proposed procedure were acceptable. A mathematical model and a dynamic simulation program are written for an activated sludge model plant along with the respiration meter based on mass balances of BODst and DO. The simulation results show that the three types of respiration rate reach steady state within 15 minutes under reasonable operating conditions. As long as the respiration rate reaches steady state the proposed procedure calculates the respiration rate that is equal to the simulated. Under constant and dynamic BODst loading, the proposed procedure is capable of calculating the effluent and influent BODst with reasonable accuracy.

scholarly journals Non-destructive handheld XRF study of archaeological composite silver objects—the case study of the late Roman Seuso Treasure

2021 ◽  
Vol 13 (5) ◽  
Author(s):  
Viktória Mozgai ◽  
Bernadett Bajnóczi ◽  
Zoltán May ◽  
Zsolt Mráv
Keyword(s):  
Fluorescence Analysis ◽  
The Body ◽  
High Quality ◽  
X Ray ◽  
Composite Objects ◽  
Mechanical Attachment ◽  
Non Destructive ◽  
Made In ◽  
Late Roman

AbstractThis study details the non-destructive chemical analysis of composite silver objects (ewers, situlas, amphora and casket) from one of the most significant late Roman finds, the Seuso Treasure. The Seuso Treasure consists of fourteen large silver vessels that were made in the fourth–early fifth centuries AD and used for dining during festive banquets and for washing and beautification. The measurements were systematically performed along a pre-designed grid at several points using handheld X-ray fluorescence analysis. The results demonstrate that all the objects were made from high-quality silver (above 90 wt% Ag), with the exception of the base of the Geometric Ewer B. Copper was added intentionally to improve the mechanical properties of soft silver. The gold and lead content of the objects shows constant values (less than 1 wt% Au and Pb). The chemical composition as well as the Bi/Pb ratio suggests that the parts of the composite objects were manufactured from different silver ingots. The ewers were constructed in two ways: (i) the base and the body were made separately, or (ii) the ewer was raised from a single silver sheet. The composite objects were assembled using three methods: (i) mechanical attachment; (ii) low-temperature, lead-tin soft solders; or (iii) high-temperature, copper-silver hard solders. Additionally, two types of gilding were revealed by the XRF analysis, one with remnants of mercury, i.e. fire-gilding, and another type without remnants of mercury, presumably diffusion bonding.

scholarly journals Influence of the variability of the odour emission rate on its impact range: a case study of the selected industrial source

2019 ◽  
Vol 100 ◽  
pp. 00070 ◽  
Author(s):  
Elżbieta Romanik ◽  
Yaroslav Bezyk ◽  
Marcin Pawnuk ◽  
Urszula Miller ◽  
Agnieszka Grzelka
Keyword(s):  
Emission Rate ◽  
Dispersion Model ◽  
Grid Size ◽  
Model Calculations ◽  
Gas Treatment ◽  
Industrial Source ◽  
Odour Concentration ◽  
Made In ◽  
Dynamic Olfactometry

Odour concentration measurements in a chosen industrial source were made in this study using the method of dynamic olfactometry. The two different scenarios considered the variation of the odour emission rate as input for the dispersion model were compared for the period 2017 (before installation of the equipment for gas treatment) and 2018 (after implementation of purifying technologies). In this paper the odour impact range was determined by applying model calculations conducted in the Polish reference dispersion model – OPERAT FB software for the grid size 2 x 2 km. The conducted research shows a significant improvement in the odour impact range of chosen industrial source in year 2018 compared to 2017.

Introducing Problem-based Learning to Special Needs Dentistry—A Case Study

2002 ◽  
Vol os9 (1) ◽  
pp. 9-13 ◽  
Author(s):  
Raman Bedi ◽  
Jackie A Champion ◽  
Roger Davies
Keyword(s):  
Special Needs ◽  
Problem Based Learning ◽  
Chi Square ◽  
Training And Education ◽  
Mixed Response ◽  
Conventional Teaching ◽  
The Subject ◽  
Better Than ◽  
Made In

Introduction In order to promote training and education in special-needs dentistry an attempt was made to introduce problem-based learning (PBL) as a method of postgraduate dental education. The aim of this paper was to review the principles of PBL and report on a case study using this methodology. Method The case study was of a PBL session, on the subject of ‘problems of obtaining appropriate dental care for people with epilepsy’, undertaken at a national conference. Delegates were asked to complete a pre- and post-session questionnaire on PBL and their attitudes to the session. Results The session received a mixed response. Only 33 (35%) thought the session was valuable and only 20 (31%) thought it was better than conventional teaching methods and yet over half (55%) said they would like to attend more PBL in special-needs dentistry. Professionals complementary to dentistry were more likely to find the PBL session of value and to prefer the method to a more conventional format than dentists were (chi-square=5.5, df=1, p<0.05 and chi-square=5.9, df=1, p<0.05 respectively). Conclusion Valuable feedback was received from delegates. This will enable improvements to be made in future courses so that the effectiveness of PBL can be optimised.

The "Right to Die": A Case Study in American Lawmaking*

1996 ◽  
Vol 3 (1) ◽  
pp. 49-74
Author(s):  
Alan Meisel
Keyword(s):  
Legal System ◽  
Right To Die ◽  
Judicial Process ◽  
Clinical Issue ◽  
The Press ◽  
American Law ◽  
American Legal System ◽  
The Right ◽  
Made In

AbstractIn the 20 years that have passed since the Karen Quinlan case exposed a simmering clinical issue to the light of day — more precisely, to the press and to judicial process — a consensus has developed in American law about how end-of-life decisionmaking should occur. To be sure, there are dissenting voices from this consensus, but they are often (though not always) about minor issues. By illustrating how this consensus has evolved, this paper explores how law is made in the American legal system and the roles that different legal and extra-legal institutions play in lawmaking.

Sign in / Sign up

Export Citation Format

Share Document