scholarly journals Experimental Evaluation of the Density Ratio Effects on the Cooling Performance of a Combined Slot/Effusion Combustor Cooling System

2013 ◽  
Vol 2013 ◽  
pp. 1-14 ◽  
Author(s):  
Antonio Andreini ◽  
Gianluca Caciolli ◽  
Bruno Facchini ◽  
Lorenzo Tarchi
Keyword(s):  
Heat Transfer ◽  
Working Conditions ◽  
Film Cooling ◽  
Cooling System ◽  
Velocity Ratio ◽  
Density Ratio ◽  
Cooling Performance ◽  
Engine Cooling ◽  
Flow Parameters ◽  
Adiabatic Effectiveness

The purpose of this study is to investigate the effects of coolant-to-mainstream density ratio on a real engine cooling scheme of a combustor liner composed of a slot injection and an effusion array with a central dilution hole. Measurements of heat transfer coefficient and adiabatic effectiveness were performed by means of steady-state thermochromic liquid crystals technique; experimental results were used to estimate, through a 1D thermal procedure, the Net Heat Flux Reduction and the overall effectiveness in realistic engine working conditions. To reproduce a representative value of combustor coolant-to-mainstream density ratio, tests were carried out feeding the cooling system with carbon dioxide, while air was used in the main channel; to highlight the effects of density ratio, tests were replicated using air both as coolant and as mainstream and results were compared. Experiments were carried out imposing values of effusion blowing and velocity ratios within a range of typical modern engine working conditions. Results point out the influence of density ratio on film cooling performance, suggesting that velocity ratio is the driving parameter for the heat transfer phenomena; on the other hand, the adiabatic effectiveness is less sensitive to the cooling flow parameters, especially at the higher blowing/velocity ratios.

scholarly journals Density Ratio Effects on the Cooling Performances of a Combustor Liner Cooled by a Combined Slot/Effusion System

2012 ◽  
Author(s):  
A. Andreini ◽  
G. Caciolli ◽  
B. Facchini ◽  
L. Tarchi ◽  
D. Coutandin ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Working Conditions ◽  
Cooling System ◽  
Velocity Ratio ◽  
Density Ratio ◽  
Perforated Plate ◽  
Flow Parameters ◽  
Adiabatic Effectiveness ◽  
Combustor Liner ◽  
Effects Of Density

The aim of the present study is to investigate the effects of density ratio between coolant and mainflow on a real engine cooling scheme of a combustor liner. Measurements of heat transfer coefficient and adiabatic effectiveness were performed by means of a steady-state Thermochromic Liquid Crystals (TLC) technique; experimental results were used to estimate, through a 1D thermal procedure (Therm1d), the Net Heat Flux Reduction and the overall effectiveness in realistic engine working conditions. In order to reproduce a representative value of combustor coolant to mainstream density ratio, tests were carried out feeding the cooling system with carbon dioxide (CO2), while air was used in the main channel; to highlight the effects of density ratio and, as a consequence, to distinguish between the influence of blowing ratio and velocity ratio, tests were replicated using air both as coolant and mainstream and results were compared. The experimental analysis was performed on a test article replicating a slot injection and an effusion array with a central large dilution hole. Test section consists of a rectangular cross-section duct and a flat perforated plate provided with 272 holes arranged in 29 staggered rows (d = 1.65 mm, α = 30°, L/d = 5.5). Furthermore a dilution hole (D = 18.75 mm) is located at the 14th row; both effusion and dilution holes are fed by a channel replicating a combustor annulus. The rig allows to control mainstream and coolant flow parameters, especially in terms of Reynolds number of mainstream and effusion holes. Located upstream the first effusion row, a 6.0 mm high slot ensures the protection of the very first region of the liner. Experiments were carried out imposing several values of effusion blowing and velocity ratios within a range of typical modern engine working conditions (BReff/VReff = 1.5; 3.0; 5.0; 7.0) and keeping constant slot flow parameters (BRsl ≈ 1.5). Results point out the influence of density ratio on film cooling performance, suggesting that velocity ratio is the driving parameter for the heat transfer phenomena; concerning the effectiveness, results show that the adiabatic effectiveness is less sensitive to the cooling flow parameters, especially at the higher blowing/velocity ratios.

Effusion-Cooling Performance at Gas Turbine Combustor Representative Flow Conditions

2012 ◽  
Author(s):  
Vinod U. Kakade ◽  
Steven J. Thorpe ◽  
Miklós Gerendás
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Free Stream ◽  
Flow Conditions ◽  
Cooling Performance ◽  
Free Stream Turbulence ◽  
High Turbulence ◽  
Adiabatic Effectiveness

The thermal management of aero gas turbine engine combustion systems commonly employs effusion-cooling in combination with various cold-side convective cooling schemes. The combustor liner incorporates many small holes which are usually set in staggered arrays and at a shallow angle to the cooled surface; relatively cold compressor delivery air is then allowed to flow through these holes to provide the full-coverage film-cooling effect. The efficient design of such systems requires robust correlations of film-cooling effectiveness and heat transfer coefficient at a range of aero-thermal conditions, and the use of appropriately validated computational models. However, the flow conditions within a combustor are characterised by particularly high turbulence levels and relatively large length scales. The experimental evidence for performance of effusion-cooling under such flow conditions is currently sparse. The work reported here is aimed at quantifying typical effusion-cooling performance at a range of combustor relevant free-stream conditions (high turbulence), and also to assess the importance of modeling the coolant to free-stream density ratio. Details of a new laboratory wind-tunnel facility for the investigation of film-cooling at high turbulence levels are reported. For a typical combustor effusion geometry that uses cylindrical holes, spatially resolved measurements of adiabatic effectiveness, heat transfer coefficient and net heat flux reduction are presented for a range of blowing ratios (0.48 to 2), free-stream turbulence conditions (4 and 22%) and density ratios (0.97 and 1.47). The measurements reveal that elevated free-stream turbulence impacts on both the adiabatic effectiveness and heat transfer coefficient, although this is dependent upon the blowing ratio being employed and particularly the extent to which the coolant jets detach from the surface. At low blowing ratios the presence of high turbulence levels causes increased lateral spreading of the coolant adjacent to the injection points, but more rapid degradation in the downstream direction. At high blowing ratios, high turbulence levels cause a modest increase in effectiveness due to turbulent transport of the detached coolant fluid. Additionally, the augmentation of heat transfer coefficient caused by the coolant injection is seen to be increased at high free-stream turbulence levels.

Endwall Heat Transfer and Cooling Performance of a Transonic Turbine Vane with Upstream Injection Flow

2021 ◽  
pp. 1-24
Author(s):  
Zhigang LI ◽  
Bo Bai ◽  
Jun Li ◽  
Shuo Mao ◽  
Wing Ng ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Density Ratio ◽  
Gas Temperature ◽  
Blow Down ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Injection Flow ◽  
Coolant Injection ◽  
Exit Mach Number

Abstract Detailed experimental and numerical studies on endwall heat transfer and cooling performance with coolant injection flow through upstream discrete holes is presented in this paper. High resolution heat transfer coefficient (HTC) and adiabatic film cooling effectiveness values were measured using a transient infrared thermography technique on an axisymmetric contoured endwall. The tests were performed in a transonic linear cascade blow-down wind tunnel facility. Conditions were representative of a land-based power generation turbine with exit Mach number of 0.85 corresponding to exit Reynolds number of 1.5 × 106, based on exit condition and axial chord length. A high turbulence level of 16% with an integral length scale of 3.6%P was generated using inlet turbulence grid to reproduce the typical turbulence conditions in real turbine. Low temperature air was used to simulate the typical coolant-to-mainstream condition by controlling two parameters of the upstream coolant injection flow: mass flow rate to determine the coolant-to-mainstream blowing ratio (BR = 2.5, 3.5), and gas temperature to determine the density ratio (DR = 1.2). To highlight the interactions between the upstream coolant flow and the passage secondary flow combined with the influence on the endwall heat transfer and cooling performance, a comparison of CFD predictions to experimental results was performed by solving steady-state Reynolds-Averaged Navier-Stokes (RANS) using the commercial CFD solver ANSYS Fluent V.15.

Numerical Investigation of Coolant-to-Mainstream Scaling Parameters With Film Cooling on Pressure and Suction Side of a Gas Turbine Blade

2017 ◽  
Author(s):  
Lingyu Zeng ◽  
Xueying Li ◽  
Jing Ren ◽  
Hongde Jiang
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Momentum Flux ◽  
Velocity Ratio ◽  
Density Ratio ◽  
Flux Ratio ◽  
Suction Side ◽  
Pressure Side ◽  
Blowing Ratio ◽  
Adiabatic Effectiveness

Most experiments of blade film cooling are conducted with density ratio lower than that of turbine conditions. In order to accurately model the performance of film cooling under a high density ratio, choosing an appropriate coolant to mainstream scaling parameter is necessary. The effect of density ratio on film cooling effectiveness on the surface of a gas turbine twisted blade is investigated from a numerical point of view. One row of film holes are arranged in the pressure side and two rows in the suction side. All the film holes are cylindrical holes with a pitch to diameter ratio P/d = 8.4. The inclined angle is 30°on the pressure side and 34° on the suction side. The steady solutions are obtained by solving Reynolds-Averaged-Navier-Stokes equations with a finite volume method. The SST turbulence model coupled with γ-θ transition model is applied for the present simulations. A film cooling experiment of a turbine vane was done to validate the turbulence model. Four different density ratios (DR) from 0.97 to 2.5 are studied. To independently vary the blowing ratio (M), momentum flux ratio (I) and velocity ratio (VR) of the coolant to the mainstream, seven conditions (M varying from 0.25 to 1.6 on the pressure side and from 0.25 to 1.4 on the suction side) are simulated for each density ratio. The results indicate that the adiabatic effectiveness increases with the increase of density ratio for a certain blowing ratio or a certain momentum flux ratio. Both on the pressure side and suction side, none of the three parameters listed above can serve as a scaling parameter independent of density ratio in the full range. The velocity ratio provides a relative better collapse of the adiabatic effectiveness than M and I for larger VRs. A new parameter describing the performance of film cooling is introduced. The new parameter is found to be scaled with VR for nearly the whole range.

Effects of Free-Stream Turbulence and Surface Roughness on Film Cooling

1996 ◽  
Author(s):  
Donald L. Schmidt ◽  
David G. Bogard
Keyword(s):  
Heat Transfer ◽  
Surface Roughness ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Momentum Flux ◽  
Free Stream ◽  
Cooling Performance ◽  
Free Stream Turbulence ◽  
Adiabatic Effectiveness

A flat plate test section was used to study how high free-stream turbulence with large turbulence length scales, representative of the turbine environment, affect the film cooling adiabatic effectiveness and heat transfer coefficient for a round hole film cooling geometry. This study also examined cooling performance with combined high free-stream turbulence and a rough surface which simulated the roughness representative of an in-service turbine. The injection was from a single row of film cooling holes with injection angle of 30°. The density ratio of the injectant to the mainstream was 2.0 for the adiabatic effectiveness tests, and 1.0 for the heat transfer coefficient tests. Streamwise and lateral distributions of adiabatic effectiveness and heat transfer coefficients were obtained at locations from 2 to 90 hole diameters downstream. At small to moderate momentum flux ratios, which would normally be considered optimum blowing conditions, high free-stream turbulence dramatically decreased adiabatic effectiveness. However, at large momentum flux ratios, conditions for which the film cooling jet would normally be detached, high free-stream turbulence caused an increase in adiabatic effectiveness. The combination of high free-stream turbulence with surface roughness resulted in an increase in adiabatic effectiveness relative to the smooth wall with high free-stream turbulence. Heat transfer rates were relatively unaffected by a film cooling injection. The key result from this study was a substantial increase in the momentum flux ratios for maximum film cooling performance which occurred for high free-stream turbulence and surface roughness conditions which are more representative of actual turbine conditions.

Influence of a Leaking Gap Downstream of the Injection Holes on Film Cooling Performance

1996 ◽  
Author(s):  
Y. Yu ◽  
M. K. Chyu
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Cooling System ◽  
Convective Transport ◽  
Hole Injection ◽  
Thermochromic Liquid Crystal ◽  
Cooling Performance ◽  
Temperature Problem

This study investigated a practical but never exploited issue concerning the influence of flow leakage through a gap downstream on the film cooling performance with a row of discrete-hole injection. A heat transfer system as such can be categorized as either a three-temperature or a four-temperature problem, depending on the direction of leakage through the gap. To fully characterize a three-temperature based film-cooling system requires knowledge of both local film effectiveness and heat transfer coefficient. A second film effectiveness is necessary for characterizing a four-temperature problem. All these variables can be experimentally determined, based on the transient method of thermochromic liquid crystal imaging. Although the overall convective transport in the region is expected to be dependent on the blowing ratios of the coolants, the mass flow ratio of the two injectants, and the geometry, the current results indicated that the extent of flow injection or extraction through the gap has significant effects on the film effectiveness and less on the heat transfer coefficient which is primarily dominated by the geometric disturbance of gap presence.

A Parametric Investigation of Vane Showerhead Film Cooling by PSP Technique

2019 ◽  
Author(s):  
H. Abdeh ◽  
G. Barigozzi ◽  
S. Ravelli ◽  
S. Rouina
Keyword(s):  
Turbulence Intensity ◽  
Film Cooling ◽  
Cooling System ◽  
Density Ratio ◽  
Leading Edge ◽  
Intensity Level ◽  
Cooling Performance ◽  
Blowing Ratio ◽  
Cylindrical Holes ◽  
Exit Mach Number

Abstract In this study a parametric analysis of the thermal performance of a nozzle vane cascade with a showerhead cooling system made of four rows of cylindrical holes was carried out by using the Pressure Sensitive Paint (PSP) technique. Coolant-to-mainstream blowing ratio (BR), density ratio (DR), main flow isentropic exit Mach number (Ma2is) and turbulence intensity level (Tu1) were the considered parameters. The cascade was tested in an atmospheric wind tunnel at Ma2is values ranging from 0.2 to 0.6, with an inlet turbulence intensity level of 1.6% and 9%, at variable injection conditions of BR = 2.0, 3.0, 4.0. Moreover, the influence of DR on the leading edge film cooling performance was investigated: testing was carried out at DR = 1.0, using nitrogen as foreign gas, and DR = 1.5, with carbon dioxide serving as coolant. In the near-hole region, higher BR and Ma2is resulted in higher effectiveness, while higher mainstream turbulence intensity reduced the thermal coverage in between the rows of holes, whatever the BR. Further downstream along the vane pressure side, the effectiveness was negatively affected by rising BR, but positively influenced by lowering the mainstream turbulence intensity. Moreover, a decrease in DR caused a reduction in the film cooling performance, whose extent depends on the injection condition.

High-Resolution Film Cooling Effectiveness Measurements of Axial Holes Embedded in a Transverse Trench With Various Trench Configurations

2006 ◽  
Vol 129 (2) ◽  
pp. 294-302 ◽  
Author(s):  
Scot K. Waye ◽  
David G. Bogard
Keyword(s):  
High Resolution ◽  
Film Cooling ◽  
Density Ratio ◽  
Field Measurements ◽  
Suction Side ◽  
Lateral Spreading ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Flow Parameters ◽  
Adiabatic Effectiveness

Adiabatic film cooling effectiveness of axial holes embedded within a transverse trench on the suction side of a turbine vane was investigated. High-resolution two-dimensional data obtained from infrared thermography and corrected for local conduction provided spatial adiabatic effectiveness data. Flow parameters of blowing ratio, density ratio, and turbulence intensity were independently varied. In addition to a baseline geometry, nine trench configurations were tested, all with a depth of 1∕2 hole diameter, with varying widths, and with perpendicular and inclined trench walls. A perpendicular trench wall at the very downstream edge of the coolant hole was found to be the key trench characteristic that yielded much improved adiabatic effectiveness performance. This configuration increased adiabatic effectiveness up to 100% near the hole and 40% downstream. All other trench configurations had little effect on the adiabatic effectiveness. Thermal field measurements confirmed that the improved adiabatic effectiveness that occurred for a narrow trench with perpendicular walls was due to a lateral spreading of the coolant and reduced coolant jet separation. The cooling levels exhibited by these particular geometries are comparable to shaped holes, but much easier and cheaper to manufacture.

Effects of Coolant Density Ratio on Film Cooling Performance on a Vane

2003 ◽  
Author(s):  
J. Michael Cutbirth ◽  
David G. Bogard
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Operating Conditions ◽  
Cooling Performance ◽  
Large Density ◽  
Performance Trends ◽  
Large Density Ratio ◽  
Small Density ◽  
Adiabatic Effectiveness ◽  
Density Ratios

Film cooling performance was studied on a simulated turbine vane model with an objective of determining how much the coolant density ratio affects this performance. Experiments were conducted using coolant density ratios of 1.8 and 1.2. The purpose of the study was to determine if tests done at small density ratios (which is often more viable in a laboratory) can give reasonable predictions of performance at more realistic large density ratios. Furthermore, appropriate scaling parameters were determined. The mainstream flow was operated with low and high turbulence levels. Adiabatic effectiveness was measured in the showerhead region of the vane, and following the first row of coolant holes on the pressure side. Adiabatic effectiveness performance using small density ratio coolant gave performance trends similar to the large density ratio coolant, but quantitative values differed by varying amount depending on operating conditions.

Scaling of Performance for Varying Density Ratio Coolants on an Airfoil With Strong Curvature and Pressure Gradient Effects

2000 ◽  
Author(s):  
Marcia I. Ethridge ◽  
J. Michael Cutbirth ◽  
David G. Bogard
Keyword(s):  
Pressure Gradient ◽  
Film Cooling ◽  
Density Ratio ◽  
Flux Ratio ◽  
Leading Edge ◽  
Suction Side ◽  
Cooling Performance ◽  
Injection Angle ◽  
Adiabatic Effectiveness ◽  
Strong Curvature

An experimental study was conducted to investigate the film cooling performance on the suction side of a first stage turbine vane. Tests were conducted on a nine times scale vane model at density ratios of DR = 1.1 and 1.6 over a range of blowing conditions, 0.2 ≤ M ≤ 1.5 and 0.05 ≤ I ≤ 1.2. Two different mainstream turbulence intensity levels, Tu∞ = 0.5% and 20%, were also investigated. The row of coolant holes studied was located in a position of both strong curvature and strong favorable pressure gradient. In addition, its performance was isolated by blocking the leading edge showerhead coolant holes. Adiabatic effectiveness measurements were made using an infrared camera to map the surface temperature distribution. The results indicate that film cooling performance was greatly enhanced over holes with a similar 50° injection angle on a flat plate. Overall, adiabatic effectiveness scaled with mass flux ratio for low blowing conditions and with momentum flux ratio for high blowing conditions. However, for M < 0.5 there was a higher rate of decay for the low density ratio data. High mainstream turbulence had little effect at low blowing ratios, but degraded performance at higher blowing ratios.

Sign in / Sign up

Export Citation Format

Share Document