scholarly journals Sago Starch-Mixed Low-Density Polyethylene Biodegradable Polymer: Synthesis and Characterization

2013 ◽  
Vol 2013 ◽  
pp. 1-7 ◽  
Author(s):  
Md Enamul Hoque ◽  
Tan Jie Ye ◽  
Leng Chuan Yong ◽  
KhairulZaman Mohd Dahlan
Keyword(s):  
Mechanical Property ◽  
Young’S Modulus ◽  
Biodegradable Polymer ◽  
Young's Modulus ◽  
Starch Content ◽  
Synthesis And Characterization ◽  
Cross Linking ◽  
Content Increase ◽  
Sago Starch ◽  
Elongation At Break

This research focuses on synthesis and characterization of sago starch-mixed LDPE biodegradable polymer. Firstly, the effect of variation of starch content on mechanical property (elongation at break and Young’s modulus) and biodegradability of the polymer was studied. The LDPE was combined with 10%, 30%, 50%, and 70% of sago for this study. Then how the cross-linking with trimethylolpropane triacrylate (TMPTA) and electron beam (EB) irradiation influence the mechanical and thermal properties of the polymer was investigated. In the 2nd study, to avoid overwhelming of data LDPE polymer was incorporated with only 50% of starch. The starch content had direct influence on mechanical property and biodegradability of the polymer. The elongation at break decreased with increase of starch content, while Young’s modulus and mass loss (i.e., degradation) were found to increase with increase of starch content. Increase of cross-linker (TMPTA) and EB doses also resulted in increased Young’s modulus of the polymer. However, both cross-linking and EB irradiation processes rendered lowering of polymer’s melting temperature. In conclusion, starch content and modification processes play significant roles in controlling mechanical, thermal, and degradation properties of the starch-mixed LDPE synthetic polymer, thus providing the opportunity to modulate the polymer properties for tailored applications.

Effect of Castor Oil Impregnation on the Physical and Mechanical Properties of Bacterial Cellulose

2012 ◽  
Vol 3 (1) ◽  
pp. 13-26
Author(s):  
Myrtha Karina ◽  
Lucia Indrarti ◽  
Rike Yudianti ◽  
Indriyati
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Bacterial Cellulose ◽  
Young’S Modulus ◽  
Castor Oil ◽  
Young's Modulus ◽  
Physical And Mechanical Properties ◽  
Scanning Electron Micrographs ◽  
Elongation At Break ◽  
Acetone Water

The effect of castor oil on the physical and mechanical properties of bacterial cellulose is described. Bacterial cellulose (BC) was impregnated with 0.5–2% (w/v) castor oil (CO) in acetone–water, providing BCCO films. Scanning electron micrographs revealed that the castor oil penetrated the pores of the bacterial cellulose, resulting in a smoother morphology and enhanced hydrophilicity. Castor oil caused a slight change in crystallinity indices and resulted in reduced tensile strength and Young's modulus but increased elongation at break. A significant reduction in tensile strength and Young's modulus was achieved in BCCO films with 2% castor oil, and there was an improvement in elongation at break and hydrophilicity. Impregnation with castor oil, a biodegradable and safe plasticiser, resulted in less rigid and more ductile composites.

Synthesis and characterization of a Ti‐Zr‐based alloy with ultra‐low Young’s modulus and excellent biocompatibility

2021 ◽  
Author(s):  
Kyong Min Kim ◽  
Yazan Al-Zain ◽  
Akiko Yamamoto ◽  
Amirah H. Daher ◽  
Ahmad T. Mansour ◽  
...  
Keyword(s):  
Young’S Modulus ◽  
Young's Modulus ◽  
Synthesis And Characterization

Tensile and water absorption properties of solvent cast biofilms of sugarcane leaves fibre-filled poly(lactic) acid

2018 ◽  
Vol 33 (3) ◽  
pp. 289-304 ◽  
Author(s):  
Kuhananthan Nanthakumar ◽  
Chan Ming Yeng ◽  
Koay Seong Chun
Keyword(s):  
Tensile Strength ◽  
Lactic Acid ◽  
Water Absorption ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Poly Lactic Acid ◽  
Infrared Analysis ◽  
Absorption Properties ◽  
Elongation At Break ◽  
Bleaching Treatment

This research covers the preparation of poly(lactic acid) (PLA)/sugarcane leaves fibre (SLF) biofilms via a solvent-casting method. The results showed that the tensile strength and Young’s modulus of PLA/SLF biofilms increased with the increasing of SLF content. Nevertheless, the elongation at break showed an opposite trend as compared to tensile strength and Young’s modulus of biofilms. Moreover, water absorption properties of PLA/SLF biofilms increased with the increasing of SLF content. In contrast, the tensile strength and Young’s modulus of biofilms were enhanced after bleaching treatment with hydrogen peroxide on SLF, but the elongation at break and water absorption properties of bleached biofilms were reduced due to the improvement of filler–matrix adhesion in biofilms. The tensile and water properties were further discussed using B-factor and Fick’s law, respectively. Furthermore, the functional groups of unbleached and bleached SLF were characterized by Fourier transform infrared analysis.

Mechanical Properties of Herbal Patches from Chitosan-Based Polymer Blends for Medical Applications

2018 ◽  
Vol 917 ◽  
pp. 52-56
Author(s):  
Jirapornchai Suksaeree
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Polymer Blends ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Hydroxypropyl Methylcellulose ◽  
Peel Strength ◽  
Elongation At Break ◽  
Zingiber Cassumunar

Recently, Thai herbs are widely used as medicine to treat some illnesses. Zingiber cassumunar Roxb., known by the Thai name “Plai”, is a popular anti-inflammatory, antispasmodic herbal body and muscle treatment. This research aimed to prepare herbal patches that incorporated the 3 g of crude Z. cassumunar oil. The herbal patches made from different polymer blends were 2 g of 3.5%w/v chitosan and 5 g of 20%w/v hydroxypropyl methylcellulose (HPMC), or 2 g of 3.5%w/v chitosan and 5 g of 20%w/v polyvinyl alcohol (PVA) using 2 g of glycerin as a plasticizer. They were prepared by mixing all ingredients in a beaker and produced by solvent casting method in hot air oven at 70±2oC. The completed herbal patches were evaluated for their mechanical properties including Young’s modulus, ultimate tensile strength, elongation at break, T-peel strength, and tack adhesion. The thickness of blank and herbal patches was 0.263-0.282 mm and 0.269-0.275 mm, respectively. Young’s modulus, ultimate tensile strength, elongation at break, T-peel strength, and tack adhesion were 104.73-142.71 MPa, 87.92-93.28 MPa, 154.39-174.98 %, 3.43-4.88 MPa, and 5.29-7.02 MPa, respectively, for blank patches, and 116.83-147.28 MPa, 89.49-100.47 MPa, 133.78-159.27 %, 2.01-3.98 MPa, and 4.03-5.19 MPa, respectively, for herbal patches. We prepared herbal blended patches made from chitosan/PVA or chitosan/HPMC polymer matrix blends incorporating the crude Z. cassumunar oil. They had good mechanical properties that might be developed for herbal medicinal application.

scholarly journals The investigation of producing bacterial cellulose fibres through hand-spun

2019 ◽  
Vol 131 ◽  
pp. 01052
Author(s):  
Yu Wang
Keyword(s):  
Tensile Strength ◽  
Bacterial Cellulose ◽  
Young’S Modulus ◽  
Filter Cake ◽  
Young's Modulus ◽  
Raw Material ◽  
Cellulose Fibres ◽  
Elongation At Break ◽  
Intermediate States

Nanocellulose fibres can be hand-spun from different intermediate states, such as nanocellulose paper and filter cake, which are made from the BC suspension as well as wet pellicle (WP) and dry pellicle (DP) from BC pellicles. In this study, it can be concluded that increasing the hanging weight can increase the Young’s modulus and the tensile strength of fibres. Nanofibres produced from BC pellicles as raw material have better performance than those made from BC suspension. The best properties obtained from the fibres produced from wet pellicles and suspended to a 100g hanging weight upon drying are Young’s modulus (33.8 GPa), tensile strength (610 MPa) and elongation at break (3.6%).

scholarly journals Enhancement of the Thermomechanical Properties of a Fly Ash- and Carbon Black-Filled Polyvinyl Chloride Composite by Using Epoxidized Soybean Oil as a Secondary Bioplasticizer

2018 ◽  
Vol 2018 ◽  
pp. 1-8
Author(s):  
Toan Duy Nguyen ◽  
Chinh Thuy Nguyen ◽  
Van Thanh Thi Tran ◽  
Giang Vu Nguyen ◽  
Hai Viet Le ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Fly Ash ◽  
Carbon Black ◽  
Soybean Oil ◽  
Young’S Modulus ◽  
Polyvinyl Chloride ◽  
Young's Modulus ◽  
Epoxidized Soybean Oil ◽  
Melt Mixing ◽  
Elongation At Break

Plasticized polyvinyl chloride (PVC) was fabricated using epoxidized soybean oil (ESBO) as a secondary bioplasticizer with dioctyl phthalate (DOP). The PVC/MFA/CB composites were prepared by melt mixing of the plasticized PVC with modified fly ash (MFA), carbon black N330 (CB), and polychloroprene (CR) in a Haake Rheomix mixer using a rotation speed of 50 rpm at 175°C for 6 min and then compressed by Toyoseiki pressure machine under 15 MPa. The effect of ESBO content on morphology, melt viscosity, tensile properties, and flame retardancy of PVC/MFA/CB composites was investigated. The obtained results showed that the incorporation of ESBO has significantly enhanced the processing ability, Young’s modulus, tensile strength, and elongation at break of the PVC/MFA/CB composites. The torque of PVC/MFA/CB composites was increased to approximately 12% when 50 wt% of DOP was replaced by ESBO. When ESBO was 20 wt% in comparison with DOP weight, the elongation at break, tensile strength, and Young’s modulus of the composites were increased to 48%, 24%, and 4.5%, respectively. Correspondingly, thermogravimetric analysis results confirmed that ESBO had improved the thermostability of the PVC composites. The ESBO have potential as a secondary bioplasticizer replacement material for DOP owing to their better thermomechanical stability.

Hybrid Nanocomposites of Poly(Lactic Acid)/Thermoplastic Polyurethane with Nanosilica/Montmorillonite

2019 ◽  
Vol 947 ◽  
pp. 77-81
Author(s):  
Natsuda Palawat ◽  
Phasawat Chaiwutthinan ◽  
Sarintorn Limpanart ◽  
Amnouy Larpkasemsuk ◽  
Anyaporn Boonmahitthisud
Keyword(s):  
Thermal Stability ◽  
Tensile Strength ◽  
Impact Strength ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Thermoplastic Polyurethane ◽  
Hybrid Nanocomposites ◽  
Poly Lactic Acid ◽  
Elongation At Break ◽  
Thermal Stability Of

The aim of this study is to improve the physical properties of poly(lactic acid) (PLA) by incorporating thermoplastic polyurethane (TPU), organo-montmorillonite (OMMT) and/or nanosilica (nSiO2). PLA was first melt mixed with five loadings of TPU (10–50 wt%) on a twin-screw extruder, followed by injection molding. The addition of TPU was found to increase the impact strength, elongation at break and thermal stability of the blends, but decrease the tensile strength and Young’s modulus. Based on a better combination of the mechanical properties, the 70/30 (w/w) PLA/TPU blend was selected for preparing both single and hybrid nanocomposites with a fix total nanofiller content of 5 parts per hundred of resin (phr), and the OMMT/nSiO2 weight ratios were 5/0, 2/3, 3/2 and 0/5 (phr/phr). The Young’s modulus and thermal stability of the nanocomposites were all higher than those of the neat 70/30 PLA/TPU blend, but at the expense of reducing the tensile strength, elongation at break and impact strength. However, all the nanocomposites exhibited higher impact strength and Young’s modulus than the neat PLA. Among the four nanocomposites, a single-filler nanocomposite containing 5 phr nSiO2 exhibited the highest impact strength and thermal stability, indicating that there was no synergistic effect of the two nanofillers on the investigated physical properties. However, the hybrid nanocomposite containing 2/3 (phr/phr) OMMT/nSiO2 possessed a compromise in the tensile properties.

Low Density Polyethylene (LDPE)/Thermoplastic Sago Starch (TPSS) Blend Filled with Kenaf Core Fiber (KCF)

2012 ◽  
Vol 626 ◽  
pp. 1048-1053
Author(s):  
Norshahida Sarifuddin ◽  
Hanafi Ismail ◽  
Ahmad Zuraida
Keyword(s):  
Starch Content ◽  
Experimental Result ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Sago Starch ◽  
Elongation At Break ◽  
Kenaf Core ◽  
Blending Method ◽  
Core Fiber ◽  
Hydrocarbon Polymer

Recently, blending of common hydrocarbon polymer with natural based materials has gain much interest towards the development of degradable composite. In this study, a series of low density polyethylene (LDPE)/thermoplastic sago starch (TPSS) blend reinforced with kenaf core fiber (KCF) with starch content ranging from 10 to 40 % were prepared via melt-blending method. For this study, kenaf loading was fixed at 20 % (by weight). The blended samples were characterized by means of tensile test and morphological study. The experimental result shows that there is a gradual decrease in tensile strength, modulus and elongation at break with increase in starch loading. The scanning electron micrograph (SEM) supports the findings of tensile properties.

scholarly journals Role of Corneal Epithelium in Riboflavin/Ultraviolet-A Mediated Corneal Cross-Linking Treatment in Rabbit Eyes

2013 ◽  
Vol 2013 ◽  
pp. 1-6 ◽  
Author(s):  
Xiangchen Tao ◽  
Haiqun Yu ◽  
Yong Zhang ◽  
Zhiwei Li ◽  
Vishal Jhanji ◽  
...  
Keyword(s):  
Young’S Modulus ◽  
Corneal Epithelium ◽  
Young's Modulus ◽  
Biomechanical Properties ◽  
Cross Linking ◽  
Control Group ◽  
Ultraviolet A ◽  
Uva Irradiation ◽  
Maximal Stress

Purpose. To evaluate the role of corneal epithelium in riboflavin/ultraviolet-A (UVA) mediated corneal collagen cross-linking treatment.Methods. Fifty New Zealand rabbits were divided into 5 groups: UVA treatment with or without corneal epithelium, UVA+riboflavin treatment with or without corneal epithelium, and control without any treatment. All rabbits were sacrificed after irradiation and subsequently 4 mm × 10 mm corneal strips were harvested for biomechanical evaluation.Results. UVA irradiation alone did not enhance the maximal stress and Young’s modulus of corneal specimens with (3.15 ± 0.56 mpa, 1.00 ± 0.09 mpa) or without (3.53 ± 0.85 mpa, 0.94 ± 0.21 mpa) the corneal epithelium, compared to specimens in the control group (4.30 ± 0.68 mpa, 1.03 ± 0.24 mpa). However, UVA irradiation combined with riboflavin significantly increased the maximal stress and Young’s modulus of corneal specimens with (5.27 ± 1.09 mpa, 1.23 ± 0.23 mpa,P<0.05) or without (7.16 ± 1.88 mpa, 1.42 ± 0.16 mpa,P<0.05) corneal epithelium when compared to the control group. The maximal stress and Young’s modulus of cornea in UVA+riboflavin and “epithelium-off” group were 35.9% and 15.4% higher compared to the UVA+riboflavin and “epithelium-on” group, respectively (P<0.05).Conclusions. Our study shows that UVA+riboflavin treatment significantly affects the biomechanical properties of the cornea with and without epithelial removal. However, corneas without epithelium seem to benefit more compared to corneas with the epithelium.

scholarly journals Properties of Raphia Palm Interspersed Fibre Filled High Density Polyethylene

2013 ◽  
Vol 2013 ◽  
pp. 1-5 ◽  
Author(s):  
Henry C. Obasi
Keyword(s):  
Particle Size ◽  
Young’S Modulus ◽  
High Density Polyethylene ◽  
Young's Modulus ◽  
High Density ◽  
Screw Extruder ◽  
Elongation At Break ◽  
Twin Screw ◽  
Partial Degradation ◽  
Different Levels

Blends of nonbiodegradable and biodegradable polymers can promote a reduction in the volume of plastic waste when they undergo partial degradation. In this study, properties of raphia palm interspersed fibre (RPIF) filled high density polyethylene (HDPE) have been investigated at different levels of filler loadings, 0 to 60 wt.%. Maleic anhydride-graft polyethylene was used as a compatibilizer. Raphia palm interspersed fibre was prepared by grinding and sieved to a particle size of 150 µm. HDPE blends were prepared in a corotating twin screw extruder. Results showed that the tensile strength and elongation at break of the blends decreased with increase in RPI loadings and addition of MA-g-PE was found to improve these properties. However, the Young’s modulus increased with increase in the amount of RPI into HDPE and compatibilization further increased the Young’s modulus. The water absorption indices and weight loss for RPI/HDPE composites were found to increase with RPI loadings but were decreased on addition of MA-g-PE.

Sign in / Sign up

Export Citation Format

Share Document